L13 电阻器 标准查询与下载

DLA DSCC-DWG-88018 REV E-2007 固定的薄膜片状.200瓦1005型电阻器

This drawing describes the requirements for a fixed, film, .200 watt, .075 X .050 chip resistor.

RESISTOR, CHIP, FIXED, FILM, .200 WATT, STYLE 0705

ASTM B84-07(2013) 精密电阻器用合金丝温度电阻常数的标准试验方法

2.1 Procedure A covers the determination of the equation of the curve relating resistance and temperature where the curve approximates a parabola. This test method may be used for wire of any metal or alloy over the temperature interval appropriate to the material. 2.2 Procedure B covers the determination of the mean temperature coefficient of resistance for wire of any metal or alloy over the temperature interval appropriate to the material. 1.1 This test method covers determination of the change of resistance with temperature of alloy wires used for resistance standards and precision resistors for electrical apparatus. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Temperature-Resistance Constants of Alloy Wires for Precision Resistors

ASTM B267-07(2013) 线绕电阻器用电阻丝的标准规格

1.1 This specification covers round wire and ribbon with controlled electrical properties for use in wire-wound resistance units and similar applications, but not for use as electrical heating elements. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Wire for Use In Wire-Wound Resistors

ASTM B114-07(2013) 分流器与精密电阻器用薄板材料温度-电阻常数的标准试验方法

3.1 This test method covers the determination of the change of resistance with temperature for precision resistors and shunts made from sheet materials. 3.2 Materials normally used in the temperature range from 0 to 80°C may be tested using this test method. 1.1 This test method covers the determination of the change of resistance with temperature of sheet materials used for shunts and precision resistors for electrical apparatus. It is applicable to materials normally used in the temperature range of from 0 to 80°C. 1.2 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units may be approximate. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Temperature-Resistance Constants of Sheet Materials for Shunts and Precision Resistors

ASTM B753-07(2013) 恒温器组件合金的标准规格

1.1 This specification describes requirements for alloys to be used as components in the manufacture of bonded multi-component thermostat metal strip. More specifically it describes alloys having composition, and thermal expansion suitable for application in thermostat metal sheet and strip. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Thermostat Component Alloys

ASTM B603-07(2013) 电热元件用拉制或轧制铁-铬-铝合金的标准规格

1.1 This specification covers annealed, drawn, or rolled shapes for electrical heating and resistance purposes of alloys consisting mainly of iron, chromium, and aluminum as detailed in Table 1. TABLE 1 Chemical Requirements Class Resistivity Range Composition Range, %   Ω·cmil/ft μΩ·cm Al Cr I 825 to 920 135 to 150 5.00 to 6.00 20 to 24 IIA 795 to 880 130 to 144 4.75 to 5.75 20 to 24

Standard Specification for Drawn or Rolled Iron-Chromium-Aluminum Alloys for Electrical Heating Elements

KS C IEC 60115-1:2006 电子设备用固定电阻器.第1部分:总规范

이 규격은 전자기기용 고정저항기에 대하여 규정하며, 품질평가 또는 다른 목적을 위하여 사용

Fixed resistors for use in electronic equipment-Part 1:Generic specification

KS C IEC 60115-9:2006 电子设备用固定电阻器.第9部分:分规范:各电阻器可单独测量的表面安装固定电阻网络

이 규격은 개별적인 측정이 가능한 저항기로 이루어진 전자기기용 표면실장 고정 네트워크저

Fixed resistors for use in electronic equipment－Part 9：Sectional specification－Fixed surface mount resistor networks with individually measurable resistors

KS C IEC 60115-9-1:2006 电子设备用固定电阻器.第9-1部分:空白详细规范:各电阻器可单独测量的表面安装固定电阻网络.评定水平EZ

개별규격지침은 품종규격을 보충하는 문서이며, 개별규격의 유형, 양식, 최소한의 포함 내용

Fixed resistors for use in electronic equipment-Part 9-1:Blank detail specification-Fixed surface mount resistor networks with individually measurable resistors-Assessment level EZ

JIS C 5381-331:2006 低压电涌保护装置用元件.第331部分:金属氧化物变阻器(MOV)用规范

この規格は，交流1000V以下又は直流1500V以下の電源線，通信回線又は信号回線に使用する金属酸化物バリスタ(以下,MOVという。)の試験方法について規定する。MOVは，高い過渡電圧から装置若しくは装置各部又は両者を保護するように設計されている。

Components for low-voltage surge protective devices -- Part 331: Specification for metal oxide varistors (MOV)

DLA QPL-29-53-2006 固定电阻器 外部(高电压,套圈终端型)仪表量程倍增器

This list has been prepared for use by or for the Government in the procurement of products covered by Specification MIL-PRF-29. Listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense.

RESISTORS, FIXED, METER MULTIPLIER, EXTERNAL (HIGH VOLTAGE, FERRULE TERMINAL TYPE)

DLA QPL-22097-103-2006 (调整型)非线绕式可变电阻器.一般规格

THE ACTIVITY RESPONSIBLE FOR THIS QPL IS THE DEFENSE SUPPLY CENTER COLUMBUS (DSCC-VQ), COLUMBUS, OH 43218-3990.

RESISTORS, VARIABLE, NONWIRE WOUND (ADJUSTMENT TYPE), GENERAL SPECIFICATION FOR

DLA MIL-PRF-26 H-2006 (功率型绕线)固定电阻器的一般规格

This specification covers the general requirements for power type, wire-wound, fixed resistors for use in electrical, communications, and associated equipment. Included are general purpose styles of 5 percent initial resistance tolerance, with power ratings ranging from 3 watts to 240 watts at 25OC, derated to 0 power at 350OC (characteristics N and V) and precision axial lead types of .1(B) percent, .5 (D) percent, and 1 (F) percent initial resistance tolerances with power ratings ranging from 1 watt to 10 watts at 25OC, derated to 0 power at 250OC (characteristic U).

RESISTORS, FIXED, WIRE WOUND (POWER TYPE) GENERAL SPECIFICATION FOR

DLA MIL-PRF-39023 D SUPP 1-2006 精密非绕线可变电阻器一般规范

This supplement forms a part of MIL-PRF-32023D, dated 5 September 2006.

RESISTORS, VARIABLE, NONWIREWOUND, PRECISION GENERAL SPECIFICATION FOR

DLA MIL-PRF-39023 D-2006 精密非绕线可变电阻器一般规范

1.1 Scope. This specification covers the general requirements for precision, nonwirewound, variable resistors whose electrical output (in terms of percent of applied voltage) are linear or nonlinear with respect to the angular position of the operating shaft. This specification includes requirements for linear and nonlinear, single turn and multiturn, single-section (cup) and multi-section variable resistors. These resistors have a resistance tolerance of ±10 percent. These resistors are capable of full-load operation at maximum ambient temperatures of 70OC and are capable for continuous operation, when properly derated, to maximum temperatures of 125OC, (see 3.1, 6.2, and figure 10). This specification includes procedures and requirements for the acquisition of category I, category II, and category III precision resistors. 1.2 Classification. 1.2.1 Part or Identifying Number (PIN).

RESISTORS, VARIABLE, NONWIREWOUND, PRECISION GENERAL SPECIFICATION FOR

NF C83-231:2006 空白详细规范.小功率固定非线绕电阻器(评级 S)

Blank Detail Specification : fixed low power non-wire wound resistors (Assessment level S).

BS EN 62319-1-1:2005 聚合热敏电阻器.直接加热的阳极阶跃函数温度系数.第1-1部分:空白详细规范.限流的应用

1.1 Method(s) of mounting (to be inserted) See 4.9 of IEC 62319-1. 1.2 Dimensions All dimensions are in millimetres or inches and millimetres; it shall be stated which dimensions are suitable for gauging. Dimensional drawing(s) shall be given in the detail specification. If necessary, the dimensions may be listed in tabular form with reference to styles or codes.

Polymeric thermistors - Directly heated positive step function temperature coefficient - Part 1-1: Blank detail specification - Current limiting application

BS EN 62319-1:2005 聚合热敏电阻.直接加热的阳极阶跃函数温度系数.第1部分:总规范

This part of IEC 62319 prescribes terms and methods of test for polymeric positive temperature coefficient thermistors, insulated and non-insulated types, typically intended for use in current limiting and overcurrent protection applications. It establishes standard terms, inspection procedures and methods of test for use in detail specifications for Qualification Approval and for Quality Assessment Systems for electronic components.

Polymeric thermistors - Directly heated positive step function temperature coefficient - Part 1: Generic specification

DLA MIL-DTL-15109 D VALID NOTICE 1-2006 海军船舶的电阻器和可变电阻器

MIL-DTL-15109D, dated 14 June 2001, has been reviewed and determined to be valid for use in acquisition.

RESISTORS AND RHEOSTATS, NAVAL SHIPBOARD

DLA QPL-23648-29-2006 隔热电阻器(热敏电阻).一般规格

This list has been prepared for use by or for the Government in the acquisition of products covered by Specification MIL-PRF-23648. Listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense.

RESISTORS, THERMAL (THERMISTOR) INSULATED, GENERAL SPECIFICATION FOR