共找到 257 条与 通用电子测量仪器设备及系统 相关的标准,共 18 页
Trial specification for verification of JS-2C model transistor reverse cut-off current testers
This specification covers three types of monitor cabinets with integral power supply and mounting facilities with interface connections for the status and alarm monitor modules.
CABINETS, MONITOR, CY-7359/FSS-9(V), CY-7360/FSS-9(V), AND CY-7361/FSS-9(V)
本标准适用于产生正弦波,频率有效范围部分或全部复盖1GHz到100GHz,并具 有正弦调频,正弦调幅,或通/断脉冲调幅的一种或一种以上调制的微波信号发生器。 本标准是信号发生器产品设计、生产和使用的技术依据,也是制定各型信号发生器产品标准的依据。
Specification for microwave reference signal generators
This interim amendment is approved for use by the US Army Belvoir Research and Development Center, Department of the Army, with MIL-C-52876B, dated 28 August 1980.
CABINETS, MONITOR, CY-7359/FSS-9(V), CY-7360/FSS-9(V), AND CY-7361/FSS-9(V) [Use In Lieu Of: ARMY MIL-C-0052876 C]
Specifies radio interference measuring apparatus for the frequency range 0.009 MHz to 1000 MHz. Based on CISPR Publication 16 and intended for use as a specific reference for the legal implementation of regulations on the permissible limits of radio interference. Methods of use of the apparatus are given in appendices.
Specification for radio-interference measuring apparatus
Gives essential definitions, establishes a selection of standard performance characteristics from which the manufacturers shall or may state requirements, and specifies tests to verify compliance with these requirements. Does not apply to pulse generators.
Method for expression of the properties of signal generators
General specification for d.c. digital voltmeters
Methods of measurement for d.c. digital voltmeters
Defines the properties of non-real time spectrum analyzers which perform an analysis of the power distribution of a signal by a sampling process. Specifies the conditions and methods for testing the properties of apparatus.
Method of expression of the properties of spectrum analyzers
This specification covers three types of mnitor cabinets with integral power supply and munting f a c i l i t i e s with interface connections for the s t a t u s and alarm nonitor nodules and a data receiver. This specification covers three types of mnitor cabinets with integral power supply and munting f a c i l i t i e s with interface connections for the s t a t u s and alarm nonitor nodules and a data receiver.
CABINETS, MONITOR, CY-7359/FSS-9(V), CY-7360/FSS-9(V), AND CY-7361/FSS-9(V)
Verification Reguiation of XFD-7A Type LF Signal Generator
General specification for general purpose low and medium speed electronic counters
Methods of measurement for electronic counters
This test method is used to determine the specific gravity of epoxy resin systems.
IPC Multi-Purpose Test Board Pattern (IPC-B-25)
Describes method for error detection in information messages by attaching one block check character to the transmitted information block (or text) and checking this character when it is received. Applicable to systems with 7-bit-coded character set according to ISO 646, and basic mode for implementing this 7-bit code in data communication systems according to ISO 1745. Conforms to rules for generating character paritity bits according to ISO 1117 that parity sense shall be odd in synchronous and even in anchroneous systems.
Information processing - Use of longitudinal parity to detect errors in information messages
Defines a modular instrumentation system (otherwise known as the CAMAC system) capable of linking transducers and other devices with digital controllers or computers. Applies to nuclear instrumentation but may be utilized for other applications.
Guide to a modular instrumentation system for data handling; CAMAC system
This specification covers solid state direct current voltage regulators or control panels used to regulate, control and protect aircraft engine driven direct current generators.
REGULATORS, VOLTAGE, AND CONTROL PANELS AIRCRAFT DIRECT CURRENT GENERATOR, GENERAL SPECIFICATION FOR
The material contained in this publication was formulated under the cognizance of the JC-24 Committee on Low Power Transistors, This publication supersedes JEDEC Publications 63 and 69.
Preferred Lead Configurations for Field-Effect Transistors
Microwave leakage from integral circuit electron tubes is a function of the adequacy of the microwave isolation of tube electrode terminals,the adequacy of closure of the microwave circuits themselves, and the integrity of the microwave connectors associa
Measurement and Warning of Radio Frequency Leakage from Microwave Tubes, Recommended Practice for
This test method covers a procedure for comparatively determining the effects of printed conductor materials, conductor cross sections, substrate materials, and processes on the temperature-D.C. current characteristics of printed wiring boards. A standard
Test to Determine the Temperature Rise as a Function of Current in Printed Conductors
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号