Q24 密封材料 标准查询与下载

GJB 5833-2006 两栖装备硅酮密封剂应用技术要求

本标准规定了两栖装备硅酮密封剂（以下简称硅酮密封剂）的质量、检验和使用要求。 本标准适用于两栖装备中密封间隙不大于6mm的箱体、法兰平面、炮塔座圈、使用常规衬垫等结合面以及电气元件和接头的密封与防腐。其它类型的装备或密封部位亦可参照使用。

The technical requirements of silicone sealants application for amphibious materiel

DIN 18541-2:2006 现场水泥接缝密封用热塑性塑料制造的止水带.第2部分:要求、试验和检查材料

Thermoplastic water stops for sealing joints in in-situ concrete - Part 2: Material requirements, testing and inspection

DIN 18541-1:2006 现场水泥接缝密封用热塑性塑料制造的止水带.第1部分:术语和定义、形状、尺寸、标记

The document applies to the concepts, shapes and dimensions of water-stops which are used for the sealing of joints in in-situ concrete. It specifies the principal design of the cross-sections and the necessary minimum dimensions as well as the rules for the marking.#,,#

Termoplastic water stops for sealing joints in in-situ concrete - Part 1: Terms and definitions, shapes, dimensions, marking

DIN EN 12691:2006 防水软板.屋顶防水用沥青、塑料和橡胶薄板.耐冲击性测定

This European Standard specifies a test for puncture by impact on sheets for roof waterproofing. Mechanical stress on waterproofing sheets ranges from static long-term loads to dynamic short-term loads. This method represents the dynamic category of load where puncture may be caused by impact. This European Standard may also be applied for other purposes of waterproofing.

Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of resistance to impact English version of DIN EN 12691:2006-06

JIS A 5759 AMD 1:2006 门窗玻璃安装用粘合薄膜（修改件1）

This translation has been made based on the Amendment to the original Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee in accordance with Industrial Standardization Law. Consequently, JIS A 5759:1998 is partially replaced with this Amendment.

Adhesive films for glazings (Amendment 1)

BS EN 14187-9:2006 冷用密封胶.试验办法.接缝密封胶的功能测试

This European Standard specifies a function test for cold applied joint sealants intended for use in joints in roads and airfield pavements in cold climate areas where the total joint movement can be greater than 35 % and the temperature can go below –25 °C.

Cold applied joint sealants - Test methods - Function testing of joint sealants

CECS 195-2006 聚合物水泥、渗透结晶型防水材料应用技术规程

本规程适用于聚合物水泥防水涂料、聚合物水泥防水砂浆和渗透结晶型防水材料的防水工程设计、施工和质量验收。 聚合物水泥、渗透结晶型防水材料的性能要求、设计、施工和质量检验、除应符合本规程要求外，尚应符合国家现行有关标准的规定。

Technical specification for polymer modified cementitous waterproofing materials and penetrating and crystalling waterproofing materials

NF P84-150:2006 防水用软薄板.混凝土船桥甲板和其他可行驶车辆的混凝土表面的防水性.吸水率的测定

Flexible sheets for waterproofing - Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles - Determination of water absorption.

DIN EN 14223:2006 防水用柔性薄板.混凝土船桥甲板和其他车辆可通过的混凝土表面的防水.吸水率的测定

This European Standard specifies a test method for the determination of water absorption in reinforced bitumen sheets which could influence the functional behaviour of these sheets. NOTE It is primarily the reinforcement's ability to absorb water which is examined by this test.

Flexible sheets for waterproofing - Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles - Determination of water absorption; English version of DIN EN 14223:2006-03

DIN EN 14224:2006 防水用柔性薄板.混凝土船桥甲板和其他车辆可通过的混凝土表面的防水.断裂桥接能力的测定.德文版本 EN 14224-2005

This document specifies a test method for determining the crack bridging ability of sheets used as water-proo-fing systems on concrete bridge decks and other areas of concrete trafficable by vehicles.

Flexible sheets for waterproofing - Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles - Determination of crack bridging ability; German version EN 14224:2005

BS EN 14188-3:2006 接缝填充物和密封胶.预成型的接缝密封件规范

This European Standard specifies requirements for preformed joint seals made of vulcanised rubber for concrete pavements. General requirements for finished joint seals are also given. This European Standard is applicable to joint seals for joints in new concrete pavements and maintenance work in concrete highways.

Joint fillers and sealants - Specification for preformed joint seals

JG/T 187-2006 建筑门窗用密封胶条

本标准规定了建筑门窗用密封胶条术语和定义、分类、代号和标记、要求、试验方法、检验规则及标志、包装、运输、贮存等。 本标准适用于建筑门窗用弹性密封胶条，建筑幕墙开启部分用胶条可参照使用，不适用于发泡、复合密封胶条。

Gaskets for doors and windows of buildings

DIN 18195 Bb.1:2006 建筑物防水.密封剂定位控制一致性的例子

Water-proofing of buildings - Examples of positioning of sealants in accordance

ASTM C1083-06(2011) 蜂窝状弹性垫圈和密封材料的吸水性的标准试验方法

This test method will quantify the water absorption characteristics of cellular elastomeric gaskets and sealing materials. It is a test that enables the specifier to exercise engineering judgment in the selection of materials.1.1 This test method covers those cellular elastomeric compounds that are manufactured in preformed shapes such as gaskets, and that are used as compression seals for glazing purposes and as sealing materials in other applications in building construction. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information purposes only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Water Absorption of Cellular Elastomeric Gaskets and Sealing Materials

ASTM C836-06 与独立磨损层一起使用的高固体含量并使用冷却液体的弹性防水薄膜的标准规范

1.1 This specification describes the required properties and test methods for a cold liquid-applied elastomeric-type membrane, one or two component, for waterproofing building decks and walls subject to hydrostatic pressure in building areas to be occupied by personnel, vehicles, or equipment. This specification applies only to a membrane system that will be covered with a separate wearing course, traffic course, or backfill. Note 18212;See Guide C 898 and Guide C 1471 for proper application of membrane.1.2 There are no ISO standards similar or equivalent to this ASTM standard.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course

ASTM C1315-06 固化混凝土和密封混凝土液膜性化合物特种性能的标准规范

1.1 This specification provides requirements for membrane-forming liquids suitable for use as curing compounds and sealers on freshly placed concrete and as sealers on hardened concrete. These membranes have special properties, such as, alkali resistance, acid resistance, adhesion-promoting qualities, and resistance to degradation by UV light.Note 1For liquid membrane-forming curing compounds specified primarily by their ability to retain water in newly placed concrete (and by drying time, and for white pigmented products, reflectance), see Specification C 309.1.2 The values stated in SI units are to be regarded as the standard. (Inch pound units are shown in parentheses).The following precautionary caveat pertains only to the test methods portion, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Liquid Membrane-Forming Compounds Having Special Properties for Curing and Sealing Concrete

ASTM C717-06a 建筑密封件和密封胶的标准术语

1.1 This standard covers terms, related standard definitions, and descriptions of terms used or likely to be used in standard test methods, specifications, guides, and practices (related to building seals and sealants) consistent with the scope and areas of interest of ASTM Committee C24.1.2 Definitions and descriptions of terms are written to ensure that building seals and sealants standards are properly understood and interpreted.

Standard Terminology of Building Seals and Sealants

ASTM D226-06 房顶和防水用沥青饱和有机毡的标准规范

1.1 This specification covers asphalt-saturated organic felts, with or without perforations, intended to be used with asphalts conforming to the requirements of Specification D 312 in the construction of built-up roofs, and with asphalts conforming to the requirements of Specification D 449 in the construction of water proofing systems.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.The following safety hazards caveat pertains only to the test method portion, Section , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing

ASTM C716-06(2011) 安装锁条衬垫和填补上光材料的标准规范

This specification can be referred to in contract documents as a method and workmanship standard for the installation of lock-strip gasket glazing systems. See also related standards (Specifications C542 and C963, Guide C964, and Terminology C717).1.1 This specification covers installation procedures for lock-strip gaskets that comply with Specification C542 and for infill glazing materials in lockstrip gasket glazing applications used in building walls which are not more than 15° from a vertical plane. The prime performance considerations are weathertightness against air and water infiltration, and structural integrity under wind loads. 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units in parentheses are provided for information only. 1.3 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.

Standard Specification for Installing Lock-Strip Gaskets and Infill Glazing Materials

ASTM C717-06 建筑密封件和密封胶的标准术语

1.1 This standard covers terms, related standard definitions, and descriptions of terms used or likely to be used in standard test methods, specifications, guides, and practices (related to building seals and sealants) consistent with the scope and areas of interest of ASTM Committee C24.1.2 Definitions and descriptions of terms are written to ensure that building seals and sealants standards are properly understood and interpreted.

Standard Terminology of Building Seals and Sealants