Q73 金属构配件 标准查询与下载

BS 1722-10:2006 栅栏.链节和焊接筛网的防盗栅栏用规范

This part of BS 1722 specifies requirements for anti-intruder chain link or welded mesh fences and gates of at least 2.4 m in height for situations that require a higher level of protection than that offered by fences conforming to BS 1722-1. It also includes requirements for the installation of the fencing at the specified location. Provision is made for either single or double extension arms. This standard includes requirements for component dimensions, together with the permissible tolerances on size. These are minimum requirements and it should normally be acceptable to use larger sizes, except if this could otherwise adversely affect the fitting of components or if replacement parts are required to match with those already present. This standard includes requirements for protective treatments. However, maintenance requirements for the fence after installation are outside the scope of this standard. It specifies concrete or steel posts and struts, steel gates and gate posts and zinc coated or plastic coated zinc coated wire or mesh infill. This standard specifies requirements for fence materials and their combination and installation. Because a fence is made up of a number of separate components of which the particular features vary, e.g. zinc coated or plastic coated wire, a number of combinations are available to the user. Annex C provides details of the fence requirements and installation site that should be agreed between the fence supplier and purchaser at the time of ordering a fence. However, as conditions vary from site to site, Annex C should not be assumed to be exhaustive.

Fences - Specification for anti-intruder fences in chain link and welded mesh

BS 1722-9:2006 栅栏.带圆形或方形竖杆和扁平横杆的低碳钢栅栏用规范

This part of BS 1722 specifies requirements for self-adjusting (nibbed) or welded mild steel (low carbon steel) fences with round or square verticals and rolled hollow section (RHS) or rolled steel joist (RSJ) posts and flat horizontals. It also specifies requirements for their installation. Maintenance of the fence after installation is outside the scope of this standard.

Fences - Specification for mild steel (low carbon steel) fences with round or square verticals and flat horizontals

DIN 18203-2:2006 建筑施工公差.第2部分:预制钢部件

The limit deviations specified in this standard apply to prefabricated building components made of steel, such as columns, girders, trusses and panels for walls, floors and roofs. This standard does not, however, cover tolerances for rolled steel sections or for other large-format rolled building products, nor does it apply to gates, doors or frames.

Tolerances in building - Part 2: Prefabricated steel components

JIS A 6519 ERRATUM 1:2006 勘误

ERRATUM

BHMA A156.26-2006 连续式铰链

1.1 This Standard establishes requirements for architectural continuous hinges used in building construction. Cycle, finish, abuse, overload, vertical wear, and strength tests are included. 1.2 Tests described in this Standard are performed under laboratory conditions. In actual usage, results vary because of installation, maintenance, and environmental conditions.

Continuous Hinges

ANSI/NAAMM HMMA861-2006 商用空心金属门和框的指导规范

Materials and fabrication methods for commercial hollow metal products, including doors, panels, frames, and windows.

Guide Specifications for Commercial Hollow Metal Doors and Frames

BS 4449:2005 混凝土增强钢.可焊增强钢.棒材、卷材和开卷产品.规范

This British Standard specifies requirements for ribbed weldable reinforcing; steel used for the reinforcement of concrete structures. The standard covers steel delivered in the form of bars, coils and decoiled products. The standard contains provisions for three steel grades, all of 500 MPa characteristic yield strength, but with different ductility characteristics. The three grades are B500A. B500B and B500C. The weldability requirements for all grades of steel are specified in terms of the chemical composition, and in particular the carbon equivalent value. Steel bars produced by re-rolling finished products, or by rolling material of which the metallurgical history is not fully documented or not known, are not covered by this British Standard. NOTE Flash welds in lengths of bar are permissible under this standard, provided all the mechanical requirements are met. However, for some purposes, purchasers might specifically require bars without flash welds, and if so this ought to be stated at the time of enquiry and/or order.

Steel for the reinforcement of concrete - Weldable reinforcing steel - Bar, coil and decoiled product - Specification

BS EN 13658-2:2005 金属板条和串珠.定义、要求和试验方法.外部粉刷

This European Standard specifies the requirements and test methods of metal lath and beads for external render-ing. This European Standard covers metal lath intended to be used for fixing to structures or solid backgrounds to pro-vide a key to hold the plaster in position. Used in this way it enables fire protecting plastering systems to be pro-vided. This European Standard covers metal beads intended to be used to improve the protection of external angles and also provide features to the external finish of the construction and which can also be used as movement or expan-sion beads. They also contribute to fire protection.

Metal lath and beads - Definitions, requirements and test methods - External rendering

CSA A123.3-05-CAN/CSA-2005 有机饱和沥青屋顶油毡.第3版

Asphalt Saturated Organic Roofing Felt Third Edition

Asphalt Saturated Organic Roofing Felt Third Edition

CSA A344.1/A344.2-05-2005 钢制货架使用说明/钢制货架设计及建造标准.第1版

Canadian Standards Association (CSA) standards are developed through a consensus standards development process approved by the Standards Council of Canada. This process brings together volunteers representing varied viewpoints and interests to achieve co

User guide for steel storage racks/Standard for the design and construction of steel storage racks First Edition

BS 7910:2005 金属结构裂纹验收评定方法指南

This guide outlines methods for assessing the acceptability of flaws in all types of structures and components. Although emphasis is placed on welded fabrications in ferritic and austenitic steels and aluminium alloys, the procedures developed can be used for analysing flaws in structures made from other metallic materials and in non-welded components or structures. The methods described can be applied at the design, fabrication and operational phases of a structure's life.

Guide to methods for assessing the acceptability of flaws in metallic structures

JG/T 178-2005 建筑结构用冷弯矩形钢管

本标准规定了建筑结构用冷弯矩形钢管的术语和定义、制造工艺及交货状态、分类和标记、技术要求、外形尺寸及截面特性、交货重量及交货长度、试验方法、验收规则、包装、标志和质量证明书等。 本标准适用于建筑结构用冷弯焊接成型矩形钢管，也适用于桥梁等其他结构，Ⅰ级钢管适用于建筑、桥梁等结构中的主要构件及承受较大动力荷载的场合，Ⅱ级钢管适用于建筑结构中一般承载能力的场合。

Cold-formed steel hollow sections for building structures

BS EN 13658-1:2005 金属板条和串珠.定义、要求和试验方法.内部粉刷

This European Standard specifies the requirements and test methods of metal lath and beads for internal plaster-ing. This European Standard covers metal lath intended to be used for fixing to structures or solid backgrounds to pro-vide a key to hold the plaster in position. Metal lath is used vertically to support linings for walls, partitions and col-umns and horizontally to support linings for ceilings and beams. Used in this way it enables fire protecting plaster-ing systems to be provided. This European Standard covers metal beads intended to be used to improve the protection of corners and also provide features to the internal finish of the construction as well as metal beads intended to be used as depth gauge beads and movement or expansion beads. They also contribute to fire protection.

Metal lath and beads - Definitions, requirements and test methods - Internal plastering

JIS A 5530 ERRATUM 1:2005 勘误

ERRATUM

SANS 10322:2005 建筑铝的表面精加工

Gives the selection and maintenance of surface finishes on exterior architectural aluminium. Is intended as a guide for specifiers, designers, installers, building owners and maintenance staff. Covers four types of surface finish, i.e. mill finishes, ano

Surface finishing of architectural aluminium

JIS A 5526:2005 H形钢桩

この規格は，土木?建築など構造物の基礎に使用するH形鋼ぐい(以下,くいという。)について規定する。

Steel H piles

BS 6510:2005 钢窗和玻璃门

This British Standard specifies requirements for the design, fabrication and performance of steel-framed windows and glazed doors. It is applicable to windows and doors fabricated into frames in a factory from mild steel profiles, hot-rolled or cold-formed, installed vertically into the external face of buildings, as single or multi-light units, in coupled assemblies when appropriate, of the following types: a) fixed light; b) side-hung open out or in; c) top-hung; d) bottom-hung; e) horizontal pivot; f) vertical pivot; g) single-leaf hinged or pivoting door; h) double-leaf hinged or pivoting door. It is not applicable to: 1) windows or doors in which any frame member is longer than 3 m; 2) patent glazing or curtain walls that span across structural floor elements; 3) kits despatched in bar form for assembly into frames on site.

Steel-framed windows and glazed doors

DIN EN 14024:2005 带保温层的金属异型材.机械特性.要求、验证和评定试验

This document specifies requirements for assessment of the mechanical strength of metal profiles incorporating a thermal barrier. It also specifies the tests to determine the characteristic values of mechanical properties of the thermal barrier profile and to assess the suitability of the thermal barrier material used. This document applies to thermal barrier profiles designed mainly for windows, doors, window walls ans curtain walls. It does not apply to thermal barriers made only of metal profiles connected with metal pins or screws.

Metal profiles with thermal barrier - Mechanical performance - Requirements, proof and tests for assessment; German version EN 14024:2004

JG/T 168-2004 建筑门窗内平开下悬五金系统

本标准规定了建筑门窗内平开下悬五金系统的定义、分类、要求、试验方法、检验规则及标志、包装、运输、贮存。 本标准适用于建筑门窗用内平开下悬五金系统。

Tilt & turn hardware system of doors and windows

JIS A 5530:2004 钢管板桩

この規格は，土留め，締切り，構造物の基礎などに使用する鋼管矢板について規定する。

Steel pipe sheet piles