Q81 供水、排水器材设备 标准查询与下载

BS EN 295-7:2013 雨水管和污水管用陶土管道系统.顶管用陶土管和接头的要求

Vitrified clay pipe systems for drains and sewers. Requirements for pipes and joints for pipe jacking

BS EN 295-2:2013 排水管和下水道用陶土管道系统. 一致性评价和采样

Vitrified clay pipe systems for drains and sewers. Evaluation of conformity and sampling

BS EN 295-1:2013 排水排污用陶土管道系统.管道、配件和接头要求

Vitrified clay pipe systems for drains and sewers. Requirements for pipes, fittings and joints

BS EN 295-6:2013 排水管和下水道用陶土管道系统. 检修孔和检查井的要求

Vitrified clay pipes systems for drain and sewers. Requirements for components of manholes and inspection chambers

BS EN 295-5:2013 排水管和下水道用陶土管道系统. 带孔的套管及管件的要求

Vitrified clay pipe systems for drains and sewers. Requirements for perforated pipes and fittings

JIS B 8570-2:2013 冷水和热水用仪表.第2部分:交易或认证用测量仪表

Meters for cold water and hot water -- Part 2: Measuring instruments used in transaction or certification

ISO 15874-2:2013 冷热水装置用塑料管道系统.聚丙烯(PP).第2部分:管

This part ISO 15874 specifies the requirements of pipes made from polypropylene (PP) for piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not intended for human consumption (domestic systems) and for heating systems under operating pressures and temperatures appropriate to the class of application (see ISO 15874-1:2013, Table 1). This part of ISO 15874 covers a range of service conditions (application classes), design pressures and pipe dimension classes. For values of T D, Tmax and Tmal in excess of those in Table 1 of ISO 15874-1:2013 do not apply. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. It also specifies the test parameters for the test methods referred to in this part of ISO 15874. In conjunction with the other parts of ISO 15874, this part of ISO 15874 is applicable to PP pipes, their joints and to joints with components of PP, other plastics and non-plastics materials intended to be used for hot and cold water installations. It is applicable to pipes with or without (a) barrier layer(s). NOTE 2 In the case of plastics pipes provided with a thin barrier layer, e.g. to prevent or greatly diminish the diffusion of gases and the transmission of light into or through the pipe wall, the design stress requirements are totally met by the base polymer (PP).

Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes

ISO 15874-3:2013 冷热水装置用塑料管道系统.聚丙烯(PP).第3部分:配件

This part of ISO 15874 specifies the characteristics of fittings for polypropylene (PP) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems under design pressures and temperatures according to the class of application (see ISO 15874-1:2013, Table 1). It covers a range of service conditions (application classes) and design pressure classes. For values of T D, Tmax and Tmal in excess of those in Table 1 of ISO 15874-1:2013 do not apply. NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. It also specifies the parameters for the test methods referred to in this part of ISO 15874. In conjunction with the other parts of ISO 15874, this part of ISO 15874 is applicable to fittings made from PP and to fittings made from other materials which are intended to be fitted to pipes conforming to ISO 15874-2 for hot and cold water installations, whereby the joints conform to the requirements of ISO 15874-5. This part of ISO 15874 is applicable to fittings of the following types: — socket fusion fittings; — electro fusion fittings; — mechanical fittings; — fittings with incorporated inserts. It is also applicable to fittings made from alternative materials which when fitted to pipes conforming to

Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings

ISO 15874-5:2013 冷热水装置用塑料管道系统.聚丙烯(PP).第5部分:系统的适用性

This part of ISO 15874 specifies the characteristics of the fitness for purpose of polypropylene (PP) piping systems, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures according to the class of application (see Table 1 of ISO 15874-1:2013).

Plastics piping systems for hot and cold water installations.Polypropylene (PP).Part 5: Fitness for purpose of the system

ISO 15874-1:2013 冷热水装置用塑料管道系统.聚丙烯(PP).第1部分:总则

This part of ISO 15874 specifies the general aspects of polypropylene (PP) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not intended for human consumption (domestic systems), and for heating systems, under design pressures and temperatures according to the class of application (see Table 1). It covers a range of service conditions (classes of application), design pressures and pipe dimension classes. Values of T D, Tmax and Tmal in excess of those in Table 1 of this part of ISO 15874 do not apply. NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. It also specifies the test parameters for the test methods referred to in this part of ISO 15874. In conjunction with the other parts of ISO 15874, this part of ISO 15874 is applicable to PP pipes, fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations.

Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General

BS EN 16146:2012 卫生开关龙头.1型和2型供水系统用卫生开关龙头的可抽出淋浴软管.通用技术规格

Sanitary tapware. Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2. General technical specification

NF T54-063-3/IN1*NF EN 12201-3/IN1:2013 供水和压力下排水和污水系统用塑料管路系统.聚乙烯(PE).第3部分:配件

Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: fittings

ANSI/NSF 330(i3)-2013 饮用水处理装置术语词汇表

Glossary of drinking water treatment unit terminology

ANSI/NSF 58(i64)-2013 反渗透饮用水处理系统

Reverse Osmosis Drinking Water Treatment Systems

ANSI/ASME A112.19.14-2013 装有双冲水装置的6升容量的抽水马桶

Six-Liter Water Closets Equipped with a Dual Flushing Device

ANSI/NSF 53(i93r1)-2013 饮用水处理装置.健康效应

Drinking Water Treatment Units - Health Effects

ANSI/NSF 53(i91)-2013 饮用水处理单元.健康效应

Drinking Water Treatment Units - Health Effects

ANSI/NSF 46(i22r2)-2013 污水处理用组件和设备的评估

Evaluation of components and devices used in wastewater treatment systems

ANSI/NSF 50(i88r1)-2013 游泳池,温泉浴场,热水浴缸和其它娱乐性水疗设施用设备

Equipment for Swimming Pools, Spas, Hot Tubs and other Recreational Water Facilities

ANSI/NSF 50(i87r1,r2,and r3)-2013 游泳池,温泉浴场,热水浴缸和其它娱乐性水疗设施用设备

Equipment for swimming pools, spas, hot tubs, and other recreational water facilities