T16 标准查询与下载

GB 18296-2019 汽车燃油箱及其安装的安全性能要求和试验方法

本标准规定了装用液体燃料的汽车燃油箱的安全性能要求和试验方法。 本标准还规定了汽车燃油箱在车辆上安装的安全要求。 本标准适用于M\N和O类汽车的金属燃油箱和塑料燃油箱。

Safety property requirements and test methods for automobile fuel tank and its installation

DL/T 642-2016 隔爆型电动执行机构

Flameproof Electric Actuator

GM 9985490-2004 为汽车应用还真螺纹密封

Samples of components or material released to this specification shall be tested for conformity with the requirements of this specification and approved by the responsible GM Department prior to the start of delivery of production level components or

Thread Sealer, Preapplied for Vehicle Applications (Revision C)

GM 9985486-2001 涂层-磷/二硫化钼/酚醛树脂

Only the latest approved standards are applicable unless otherwise specified.

Coating - Phosphate/Molybdenum Disulfide/Phenolic Resin (Revision C)

GM 9985504-1989 乙二醇型(反-冻结)冷却液集中-汽车发动机

good impact strength and dimensional stability even at higher temperatures, e.g. housing-taillamp Spritzgie?type zur Herstellung technischer Teile mit guter Schlagzahigkeit und Dimensionsstabilitat auch bei erhohten Temperaturen, z.B. Gehause-Heckleucht

Coolant Concentrate - Automotive Engine, Glycol Type (Anti-Freeze)

GM 9985522-1989 萤光染料发动机机油泄漏检测

Unbeschadet etwaiger durch den Abnehmer erfolgenden StichprobenprUfungen tragt der LieferaAe Verantwortung dafür, da? die gelieferte Ware die Opel-Zeichnungsvorschnfien erfüllt. Ein Pnifbencht mit zahlenma?igen Ergebnissen aus PNfungen der Lieferung selbs

Dye, Fluorescent, Engine Oil Leak Detection

GM 9985536-1989 536级厌氧粘接密封

Freigabemuster, für die diese Vorschrift zutrifft, müssen nach dieser Vorschrift geprüft werden und von der Produktentwicklung und Konstruktion genehmigt sein

Adhesive Sealant, Anaerobic, Grade 536

GM 9985541-1989 萤光机油泄漏检测添加剂

Copyright General Motors Europe Reproduced by IHS under license with GME Not for ResaleNo reproduction or networking permitted without

Additive, Fluorescent Engine Oil Leak Detection

GM 9985540-1989 掩蔽-黑纸张磁带胶粘剂

General Motors Europe Reproduced by IHS under license with GME Not for ResaleNo reproduction or networking permitted without license from IHS-

Adhesive, Tape, Paper, Masking - Black

GM 9985482-1989 1.10mm直径圆螺旋槽丝

Samples of components or material released to this specification shall be tested for conformity with the requirements of this specification and approved by the responsible GM Department prior to the start of delivery of production level components or

Wire, Spiral Grooved, Round, 1.10 mm dia

GM 9985544-1989 液体粘接剂

This material specification describes the general requirements of blends of Polypropylene and EPDM resp. EPM with fillers, which are used in injection moulding or extrusion for interior and exterior components of the automotive body.

Adhesive, Liquid