V16 热加工工艺 标准查询与下载

HB/Z 136-1988 航空结构钢热处理说明书

本标准规定了航空产品用结构钢的热处理类别、设备控制、工艺控制、生产过程控制、质量控制及检验等有关要求。 　　本标准适用于航空结构钢制件的热处理。

Instructions for Heat Treatment of Aeronautical Structural Steel

QJ 1428-1988 热处理炉温控制与测量

Heat treatment furnace temperature control and measurement

QJ 1398-1988 磁滞合金的热处理

Heat Treatment of Hysteresis Alloys

AECMA PREN 3310-1988 航空航天系列.TI-P63加热处理溶液处理和老化溶液处理2级De小于或等于360 mm

This standard specifies the characteristics for self-locking bihexagonal nuts in NI-P101HT, silver plated on thread, for aerospace applications.

Titanium Alloy TI-P63 Not Heat Treated Reference Heat Treatment: Annealed Grade 2 Forging Stock De Less Than or Equal to 360 mm

AECMA PREN 2658-1988 航空航天系列Co-P93HT 抗热钴基合金非热处理:溶液处理锻造模具De小于或等于360mm

This standard specifies for the aerospace application, ttie mechanical properties for forging stock De ≤ 360 mm, not heat treated, reference heilt treatment : solution treated, in heat resisting cobalt base alloy Co-F93HT. Unless otherwise specified by the drawing, the order or the inspection schedule, the present standard shall be used in conjunction with the referenced EN standards.

Heat Resisting Cobalt Base Alloy Co-P93HT Not Heat Treated Reference Heat Treatment: Solution Treated Forging Stock De Less Than or Equal to 360 mm

QJ 1580-1988 铸造铁铬钴钼高矫顽力可加工永磁合金热处理规范

Heat treatment specification for cast iron chromium cobalt molybdenum high coercivity machinable permanent magnet alloy

NF L06-383:1987 航空航天结构件的焊接和钎焊组件.电阻点焊或滚焊的接组件.焊接组件质量

Welded and brazed assemblies for aerospace constructions. Resistance spot or seam welded assemblies. Quality of welded assemblies.

NAVY DOD-I-24688-1987 开路聚酰亚胺泡沫吸收声热型绝缘板

This specification establishes the requirements for fire resistant thermal and acoustic absorptive open-cell polyimfiodaem insulation panels for usei n shipboard applications (see6 .1).

INSULATION PANEL, THERMAL AND ACOUSTIC ABSORPTIVE, OPEN-CELL POLYIMIDE FOAM

QJ 1290-1987 结构钢、不锈钢电阻点、缝焊工艺

Structural steel, stainless steel resistance point, seam welding process

NAVY MIL-S-85848-1987 热收缩识别标记编制的一般规格

e c i f i c a t i o n e s t a b l i s h e s the r e q u i r e m e n t s for various types of i d e n t i f i c a t i o n s l e e v i n g t h a t will s h r i n k to a predetermined size upon the a p p l i c a t i o n of h e a t a f t e r it has been marked. Continuous operating t e m p e r a t u r e r a t i n g s r a n g e from -55" to 175°C (-67" to 347°F). (See 6.1).

SLEEVING, FOR IDENTIFICATION MARKING, HEAT SHRINKABLE, GENERAL SPECIFICATION FOR

HB 5363-1986 航空焊接质量控制标准

本文件是航空工厂控制航空产品质量，制定焊接工艺质量标准，改进焊接技术管理，以及焊接工艺设计和技术改造的依据。

Aviation welding quality control standard

QJ 1165-1987 不锈钢薄板熔焊技术条件

Specifications for fusion welding of stainless steel sheets

QJ 1105-1986 铸造铝镍钴永磁（硬磁）合金热处理

Cast AlNiCo permanent magnet (hard magnetic) alloy heat treatment

DIN 65169:1986 航空和航天.钎焊和高温钎焊元件.设计指导性说明

This standard applies to the design of brazed and high-temperature brazed metallic components for aerospace use.; To achieve brazings of high quality and high component safety, a number of factors has to be considered: base material, solder and auxiliary material, joint configuration, surface preparation, procedures such as furnace brazing, flame brazing, induction brazing, utilization of jigs or fixtures, mechanical stresses, tightness, corrosion resistance, operating temperature of the component, suitability for repair and inspection.#,,#

Aerospace; brazed and high-temperature brazed components; directions for design

DIN 65144:1986 航空和航天.热喷镀部件.技术规范

The standard is intended to be applied for the production or repair of aerospace components by thermal spraying at plants manufacturing parts in conformity with this standard.; The layers obtained by thermal spraying are subdivided into three safety classes according to their function and the effects of failures on aircraft safety.; The conditions required for thermal spraying to this standard are only given when the plant has a responsible specialist assigned and thermal spraying is carried out with appropriate spraying equipment and facilities tested in accordance with DIN 23521 and operated by a qualified personnel.

Aerospace; thermally sprayed components; technical specification

HB 5339-1986 航空金属结构胶接质量控制标准

本标准适用于航空金属结构胶接的质量控制。

Quality Control Standards for Adhesive Bonding of Aeronautical Metal Structures

QJ 972-1986 电子束焊接技术条件

Electron beam welding technical conditions

DIN 65083:1986 航空和航天.钛及钛合金铸件的热处理

Aerospace; heat treatment of castings of titanium and titanium alloys

ARMY MIL-C-11796 C-1986 热态喷浆矿脂防腐化合物

This commercial item description covers brown kraft paper used for general wrapping applications.

CORROSION PREVENTIVE COMPOUND, PETROLATUM HOT APPLICATION

QJ/Z 127-1984 变形铝合金的热处理

Heat Treatment of Deformed Aluminum Alloy