V38 液压、冷气系统及其附件 标准查询与下载

GJB 3466A-2010 航空涡轮冷却器通用规范

本规范规定了航空涡轮冷却器的通用要求和质量保证规定。 本规范适用于航空涡轮冷却器的研制和生产。

General specification for aircraft turbine cooling

KS W ISO 2434:2009 航空器用非呼吸用压缩空气

이 표준은 항공기용 오일 윤활 장비에서 압축된 비호흡 공기의 압력과 특성을 규정한 것이다.

Compressed non-breathing air for use in aircraft

KS W ISO 7169:2009 航空航天.液压系统用24°锥形的、压力范围截至3000psi或21000kPa的可拆卸管接头.采购规范(英制/米制)

이 표준은 표준 24° 원뿔 이음쇠의 품질과 제작에 대한 성능과 품질 요구조건을 규정하고

Aerospace-Separable tube fittings for fluid systems, for 24° cones, for pressures up to 3 000 psi or 21 000 kPa-Procurement specification, inch/metric

BS ISO 22089:2009 航空航天学.液压动力传送设备.通用规范

Aerospace - Hydraulic power transfer units - General specifications

ISO 22089:2009 航空航天系列.液压传动传输装置.通用规范

Aerospace - Hydraulic power transfer units - General specifications

SAE AS5192C-2008 内部直螺纹端口三通管配件

Fitting, Tee, Internal Straight Thread Port

DIN EN 2624:2008 航空航天系列.液压系统元件的压力脉冲试验

Aerospace series - Pressure impulse testing of hydraulic system components; German and English version EN 2624:2007

SAE AIR887C-2008 液体过滤器评定用参数和试验

This SAE Aerospace Information Report (AIR) identifies and explains the meaning of various ratings and terms used todescribe the physical characteristics of liquid filter elements. The significance of various filter parameters is discussed. Inaddition, a number of filter test methods are briefly described. This AIR and the data presented are only applicable wherethe system liquid wets the filter elements.

Liquid Filter Ratings, Parameters and Tests

SAE AS5808-2008 3000 psi液压分支轴向陷型内螺纹非扩口三通组装配件

Fitting Assembly, Tee, Female Flareless and Axially Swage on Run, Female Flareless on the Branch, Hydraulic, 3000 psi

Fitting Assembly, Tee, Female Flareless and Axially Swage on Run, Female Flareless on the Branch, Hydraulic, 3000 psi

BS ISO 8574:2008 航空航天.液压系统管路安装.弯曲管道的合格试验

This International Standard specifies pressure impulse and burst test procedures for determining and classifying the impulse fatigue strengths of bent tubes used in aerospace hydraulic systems. The procedures are intended for qualification purposes of high- and low-pressure system tubing or for the evaluation of new materials for hydraulic system tubing. NOTE Requirements for tubing used in aerospace hydraulic systems are given in ISO 8575.

Aerospace. Hydraulic system tubing. Qualification tests for bent tubes

BS ISO 16031-1:2008 航空航天液压系统.英制系列O型密封圈.内直径和横截面,公差和尺寸认证编码.液压系统用紧公差

This part of ISO 16031 specifies the inside diameters, cross-sections, tolerances and size identification codes for inch O-rings used in aerospace fluid systems. The dimensions and high precision tolerances specified in this part of ISO 16031 are suitable for nitrite and ethylene propylene materials intended for use in high pressure hydraulic fluid systems provided that suitable tooling be available.

Aerospace fluid systems. O-rings, inch series. Inside diameters and cross sections, tolerances and size-identification codes. Close tolerances for hydraulic systems

SAE AIR5829-2008 航空器液压系统中的空气

This SAE Aerospace Information Report (AIR) discusses the forms that air may take in aircraft hydraulic systems. Further, the effects of the various air forms on system operation are addressed. Recommended system design to prevent air effects and maintenance procedures to prevent and remove air are provided. Nitrogen leakage from accumulators is also a source of gas in hydraulic systems and may compose a portion of the "air" in the hydraulic system. The term "air" in this report does not differentiate between a gas composed strictly of normal atmospheric air or one that includes a mixture of additional nitrogen as well. The discussions of the report apply equally with any proportions of atmospheric air and nitrogen in the system.

Air in Aircraft Hydraulic Systems

SAE AS603A-2008 液压软管、管道和配件组件的脉冲试验

This SAE Aerospace Standard (AS) establishes the requirements and procedures for impulse testing of hose, tubing, and fitting assemblies for use in aerospace hydraulic systems of 8000 psi nominal operating pressure or less. It also refers to standard impulse test equipment to be used in conducting these impulse tests.

Impulse Testing of Hydraulic Hose, Tubing, and Fitting Assemblies

SAE ARP5891-2008 航空器液压系统加工过程中达到的清洁程度标准

This SAE Aerospace Recommended Practice (ARP) establishes the processes to achieve and maintain the required cleanliness levels in flight vehicle hydraulic systems during fabrication, assembly and pre-flight functional tests. This recommended practice covers exclusion and removal primarily of solid contaminants that occur or are created during these successive steps. The flushing procedure for installed tubing is detailed. This ARP does not address contamination levels of hydraulic fluids as purchased, operation and maintenance of ground carts, details of component cleanliness or of contamination measurement. This ARP applies to military aircraft and helicopters designed to SAE AS 5440, commercial aircraft hydraulic systems designed to SAE ARP 4752 and commercial helicopter hydraulic systems designed to SAE ARP 4925.

Achieving Cleanliness Standards for Aircraft Hydraulic Systems During Manufacture

KS W 1830-2007 航空器高压、油压软管

? ??? ???? ?? ??? ?? ??(?? ??? ??.)? ??? ????.

Hose, hydraulic, high pressure

SAE ARP4752A-2007 航空航天系列.商用运输航空器液压系统的设计和安装

This SAE Aerospace Recommended Practice (ARP) establishes the requirements for the design and installation of a commercial aircraft hydraulic system, including the applicable airworthiness regulations that affect the hydraulic system. This ARP also provides information and guidelines on the many factors that arise in the design process to provide cost effectiveness, reliability, maintainability and accepted design and installation practices.

(R) Aerospace - Design and Installation of Commercial Transport Aircraft Hydraulic Systems

DLA MS27237 REV F-2007 液压旋转法兰软管的1/2至3个油管大小

Dimensions are in inches.

SHOULDER, SWIVEL FLANGE, ADAPTER, HOSE TO TUBE, HYDRAULIC FUEL AND OIL LINES, 1/2 THROUGH 3 IN. TUBING SIZES

DLA MS28781 REV E-2007 3,000 PSI高压液压90度扣押扩口软管接头

This specification is approved for use by all Departments and Agencies of the Department of Defense.

FITTING END, 90 DEGREES ELBOW, ATTACHABLE, HYDRAULIC, HIGH PRESSURE HOSE (3,000 PSI), FLARED TUBE

DLA MS28780 REV F-2007 3,000 PSI高压液压45度扣押扩口软管接头

This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-8789.

FITTING END, 45?ELBOW, ATTACHABLE, HYDRAULIC, HIGH PRESSURE HOSE 3,000 PSI, FLARED TUBE

DIN EN 3868:2007 航空航天系列.管连接件、活动法兰和密封件.TI-P64001型钛合金焊接法兰联接件

The document specifies the characteristics of welded flanged connectors in titanium alloy TI-P64001 for aerospace applications.

Aerospace series - Pipe couplings, loose flanges and seals - Flange connectors, welded, in titanium alloy TI-P64001; German and English version EN 3868:2004