W56 毯类 标准查询与下载

BS EN ISO 24342:2012+A1:2012 弹性和纺织地板覆盖物.瓷砖边长度、边缘、边直度和直角度的测定

Resilient and textile floor-coverings. Determination of side length, edge, straightness and squareness of tiles

ASTM D3936-12 绒头纱线地毯二次背衬剥离电阻的标准试验方法

This test method is used for acceptance testing of commercial shipments. Comparative tests as directed in 5.2 may be advisable. In a case of a dispute arising from differences in reported test results when using this test method, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test samples that are as homogenous as possible and are from a lot of material of the type in question. The test samples then should be assigned randomly in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using a statistical test for unpaired data and an acceptable probability level chosen by the two parties before testing is begun. If a bias is found, either its cause must be found and corrected or the purchaser and the supplier must agree to interpret future test results with consideration to the known bias. This test method is useful to evaluate quality and cost control during the manufacture of pile yarn floor covering. Both appearance and performance of the pile floor covering can be affected by delamination of the secondary backing.1.1 This test method covers the measurement of the resistance to delamination of the secondary backing applied to some pile yarn floor coverings. 1.2 This test method is applicable to all backings including natural manufactured fibers or attached cushion. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Resistance to Delamination of the Secondary Backing of Pile Yarn Floor Covering

ANSI/NFSI B101.6-2012 为减少滑倒,绊倒和跌倒的商用入口铺垫标准指南

Provides the criteria for the selection, installation, inspection, care, and maintenance of entrance mats and runners in commercial facilities in reducing slips, trips, and falls.

Standard Guide for Commercial Entrance Matting in Reducing Slips, Trips and Falls

ANSI/NSF 140(i16)-2012 地毯可持续性评价

Sustainability Assessment for Carpet

ANSI/NSF 140(i17)-2012 地毯耐用性评估

Sustainability Carpet Assessment

ASTM D1335-12 绒头纱线地毯绒面厚度的标准试验方法

Test Method D1335 for tuft bind of pile yarn floor coverings is being used for acceptance testing of commercial shipments. Comparative tests as directed in 5.1.1 may be advisable. In case of a dispute arising from differences in reported test results using this test method, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended from the investigation of bias. As a minimum, the two parties should take a group of test samples that are homogeneous as possible and are from a lot of material of the type in question. The test samples should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using appropriate statistical analysis, and a probability level chosen by the two parties before testing begun. If a bias is found, either its cause must be found and corrected or the purchaser and the supplier must agree to interpret future test results with consideration to the known bias. The satisfactory performance of a pile yarn floor covering depends to a considerable extent on the maintenance of its original appearance. In a cut pile yarn floor covering an inadequate tuft bind may result in complete loss of pile in areas exposed to severe wear. In a looped pile yarn floor covering with inadequate tuft bind the pile loops may be pulled out to form unsightly long loops which may be hazardous.1.1 This test method covers the measurement of force required to pull or break a tuft from a pile floor covering sample. 1.2 This test method is applicable to both cut and loop pile yarn floor covering. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Tuft Bind of Pile Yarn Floor Coverings

ANSI/NSF 140(i18)-2012 地毯耐用性评定

Sustainability Assessment for Carpet

ANSI/NSF 332(i7r1)-2012 弹性地板的可持续性评估

Sustainability Assessment for Resilient Flooring

ASTM D6119-12 团纱地板覆盖物由足摩擦产生明显表面变化的标准操作规程

By exposure to sufficient traffic, this practice can be applied to any pile yarn floor covering which undergoes changes in surface appearance. This practice does not simulate surface appearance changes due to soiling, pivoting, or rolling traffic, or traffic on stairs.1.1 This practice covers the trafficking of pile yarn floor coverings in a laboratory in order to effect a change in surface appearance as a result of exposure to foot traffic under controlled conditions. A separate test method covers the assessment of surface appearance change using the CRI Reference Scales. 1.2 This practice is applicable to most changes in surface appearance observed in all types of carpet that are intended for residential or commercial use. It eliminates change in appearance associated with soiling by focusing on appearance change due to matting, flattening, or change in pile fiber configuration. Although “pile reversal” or “watermarking” is occasionally visible, this practice is not a reliable method for producing this phenomenon. 1.3 This practice may be used by mutual agreement between the purchaser and supplier to set purchasing specifications. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.

Standard Practice for Creating Surface Appearance Changes in Pile Yarn Floor Covering from Foot Traffic

ASTM D5432-12 单位和家用毛毯制品的标准性能规范

Upon mutual agreement between the purchaser and the supplier, woven products intended for this end use should meet all of the requirements listed in Table 1 of this specification. It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable products that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the supplier. In such cases, any references to the specification shall specify that: This product meets Specification D5432 except for the following characteristic(s). Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 4.2, ultimate consumer demands dictate varying performance parameters for any particular style. The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.1.1 This specification covers the evaluation of specific performance characteristics of importance in thermal woven, conventional woven, flocked, nonwoven, and knitted blanket products for use in institutional and household environments. 1.2 This specification may be used by mutual agreement between the purchaser and the supplier to establish purchasing specification requirements. 1.3 The requirements in Table 1 apply to the length and width directions for those properties where fabric direction is pertinent. 1.4 This specification does not include requirements for electric blankets. Electric blankets are specified under UL 964 requirements dictated by the Underwriter''s Laboratories. 1.5 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. TABLE 1 Specification Requirements CharacteristicRequirements Knits/FlockWoven/NonwovenSection Breaking Force (CRT. . .89 N (20 lbf) min7.1.1 method)A each direction Bursting force,345 kpa (50 psi) min7.1.2 (ball burst)A Dimensional change: After 5 launderings 7.2.1 each direction Wool (50 % or more)6.0 max

Standard Performance Specification for Blanket Products for Institutional and Household Use

ANSI/ASTM F2828:2012 湿法提取清洁设备的地毯清洁效力的测量用试验方法

Test Method for Measuring the Carpet Cleaning Effectiveness of Wet Extraction Cleaners

ASTM D6962-12 绒头纱线地板覆盖物用辊式座椅试验机操作的标准操作规程

This practice is applicable for use in testing the durability of pile yarn floor covering of all types. This practice is designed to simulate the stress on a pile yarn floor covering from the action of weighted roller chair casters over an extended period of time. The specimen is tested under conditions that may simulate an actual flooring installation. This may include the pile yarn floor covering plus a specified underlayment cushion. This practice is used to prepare specimens for additional testing, including but not limited to: visual assessment of delamination of the secondary backing, visual assessment of the pile surface, resistance to delamination measurement, tuft bind, and pile yarn raveling.1.1 This practice covers a procedure for the operation of a weighted roller chair testing device that rotates and moves across a test specimen of pile yarn floor coverings. 1.2 This practice is applicable for testing unused pile yarn floor covering of all types. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Operation of a Roller Chair Tester for Pile Yarn Floor Coverings

ANSI/NSF 140(i22)-2012 地毯耐用性评价

Sustainability Assessment for Carpet

ASTM D6540-12 绒头纱线地板覆盖物绒头联结的标准试验方法

This test method may be used to soil test specimens in the absence of abrasive wear and texture changes under controlled conditions using a standard synthetic soil, or as a preliminary step to other procedures. This test method will provide a uniformly soiled test specimen to evaluate, is reproducible (see section 11), and is economical for Testing Laboratories. This test method has been found to give results similar to the actual floor service soiling, but its use is recommended only as a screening test method and not as a replacement for floor testing. The acceptance criteria of this test method shall be set by mutual agreement between the purchaser and supplier.1.1 This test method describes the equipment, and the test method for assessing the propensity of pile yarn floor coverings to soiling in the absence of abrasive wear and texture changes, using a standard synthetic soil composition. 1.2 This test method is applicable for use in testing unused pile yarn floor covering of all types. It is not applicable for use in testing used pile yarn floor covering. 1.3 This test method can be used to compare the soiling propensity of two or more carpets; or it can be used to soil carpets as a preliminary step to other test procedures. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Accelerated Soiling of Pile Yarn Floor Covering

ANSI/NFSI B101.5-2012 用以确定地板用织物,有涂料的地板用织物和处理过的地板用织物潮湿条件下的静态摩擦系数的统一标记法标准指南

Sets forth a uniform product labeling method that identifies the wet static coefficient of friction (traction) of floor coverings, floor coverings with coatings, and treated floor coverings.

Standard Guide for Uniform Labeling Method for Identifying the Wet Static Coefficient of Friction (Traction) of Floor Coverings, Floor Coverings with Coatings, and Treated Floor Coverings

ASTM D6283-12 非包覆的绒头纱线地板覆盖物绒头长度的标准试验方法

The determination of the tuft length of pile yarn floor covering is useful in quality and cost control during the manufacture of pile yarn floor covering. Both appearance and performance can be affected by changes in this characteristic. In case there are disputable differences between reported test results for two or more laboratories, comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. At a minimum, test samples should be used that are as homogeneous as possible, that are drawn from the material from which disputable test results were obtained, and that are assigned randomly in equal numbers to each laboratory for testing. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.1.1 This test method covers the measurement of tuft length and pile yarn length of uncoated pile floor coverings. 1.2 Usually the tuft elements measured as directed in this test method will each be bound at only one binding site, but this test method also may be used for tuft elements bound at more than one binding site, provided that every tuft element measured is bound at the same number of binding sites. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This practice does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this practice to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. FIG. 1 Cross-Section of Tufted Pile Yarn Floor Covering

Standard Test Method for Tuft Element Length of Uncoated Pile Yarn Floor Coverings

ANSI/NSF 140(i19)-2012 地毯耐用性评估

Sustainability Assessment for Carpet

ANSI/NSF 140(i21)-2012 地毯耐用性评估

Sustainability Carpet Assessment

KS K ISO 4918:2011 弹性铺地物、纺织铺地物和层压板铺地物.脚轮椅试验

이 표준은 다음에 대한 방법을 규정한다.a) 텍스타일 바닥재의 마모 거동 평가b

Resilient, textile and laminate floor coverings－Castor chair test

KS K ISO 24011:2011 弹性地板铺装.普通和装饰油毡规范

이 표준은 타일(tile) 혹은 롤(roll) 형태로 공급되는 플레인 및 장식 리놀륨의 특

Resilient floor coverings－Specification for plain and decorative linoleum