E15 海洋石油作业 标准查询与下载

ISO 19905-3:2021 石油和天然气工业. 移动式海上装置的现场特定评估. 第3部分: 浮动装置

This document specifies requirements and recommendations for the site-specific assessment of mobile floating units for use in the petroleum and natural gas industries. It addresses the installed phase, at a specific site, of manned non-evacuated, manned evacuated and unmanned mobile floating units. This document addresses mobile floating units that are monohull (e.g. ship-shaped vessels or barges); column-stabilized, commonly referred to as semi-submersibles; or other hull forms (e.g. cylindrical/ conical shaped). It is not applicable to tension leg platforms. Stationkeeping can be provided by a mooring system, a thruster assisted mooring system, or dynamic positioning. The function of the unit can be broad, including drilling, floatel, tender assist, etc. In situations where hydrocarbons are being produced, there can be additional requirements. This document does not address all site considerations, and certain specific locations can require additional assessment. This document is applicable only to mobile floating units that are structurally sound and adequately maintained, which is normally demonstrated through holding a valid RCS classification certificate. This document does not address design, transportation to and from site, or installation and removal from site. This document sets out the requirements for site-specific assessments, but generally relies on other documents to supply the details of how the assessments are to be undertaken. In general: — the hull structure and air gap are assessed by use of a comparison between the site-specific metocean conditions and its design conditions, as set out in the RCS approved operations manual; mobile floating drilling units. Equivalent alternative methodologies can be used; — IMCA M 220 is referenced for developing an activity specific operating guidelines. Agreed alternative methodologies can be used. NOTE RCS rules and the IMO MODU code[13] provide guidance for design and general operation of mobile floating units.

Petroleum and natural gas industries - Site-specific assessment of mobile offshore units - Part 3: Floating units

SY/T 0308-2016 滩海石油工程注水设计规范

Water injection design specifications for offshore petroleum projects

KS B ISO 19900:2014 石油和天然气工业.海洋结构的通用要求

Petroleum and natural gas industries — General requirements for offshore structures

KS B ISO 19900:2010 石油和天然气工业.海洋结构的通用要求

이 표준은 알려져 있거나 또는 예측 가능한 작용을 받는 구조물의 설계 및 평가에 대한 일반

Petroleum and natural gas industries-General requirements for offshore structures

ISO 13628-11:2007/cor 1:2008 石油和天然气工业.水底生产系统的设计和运行.第11部分:海底和海上设备用软管系统.技术勘误1

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 11: Flexible pipe systems for subsea and marine applications; Technical Corrigendum 1

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 11: Flexible pipe systems for subsea and marine applications; Technical Corrigendum 1

ISO 13628-2:2006 石油和天然气工业.水下采油系统的设计和操作.第2部分:海底和海洋设备用游离软管系统

This part of ISO 13628 defines the technical requirements for safe, dimensionally and functionally interchangeable flexible pipes that are designed and manufactured to uniform standards and criteria. Minimum requirements are specified for the design, material selection, manufacture, testing, marking and packaging of flexible pipes, with reference to existing codes and standards where applicable. See ISO 13628-11 for guidelines on the use of flexible pipes and ancillary components. This part of ISO 13628 applies to unbonded flexible pipe assemblies, consisting of segments of flexible pipe body with end fittings attached to both ends. This part of ISO 13628 does not cover flexible pipes of bonded structure. This part of ISO 13628 does not apply to flexible pipe ancillary components. Guidelines for bend stiffeners and bend restrictors are given in Annex B. NOTE 1 Guidelines for other components are given in ISO 13628-11. This part of ISO 13628 does not apply to flexible pipes that include non-metallic tensile armour wires. Pipes of such construction are considered as prototype products subject to qualification testing. The applications addressed by this part of ISO 13628 are sweet and sour service production, including export and injection applications. Production products include oil, gas, water and injection chemicals. This part of ISO 13628 applies to both static and dynamic flexible pipes used as flowlines, risers and jumpers. This part of ISO 13628 does not apply to flexible pipes for use in choke-and-kill line applications. NOTE 2 See API Specification 16C for choke-and-kill line applications. NOTE 3 ISO 13628-10 provides guidelines for bonded flexible pipe.

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 2: Unbonded flexible pipe systems for subsea and marine applications

ISO 13628-10:2005 石油和天然气工业.水下采油系统的设计和操作.第10部分:连接柔性管规范

1.1 Purpose 1.1.1 This part of ISO 13628 defines the technical requirements for safe, dimensionally and functionally interchangeable bonded flexible pipes that are designed and manufactured to uniform standards and criteria. See Figure 1 for explanatory figure on typical bonded flexible pipe. 1.1.2 Minimum requirements are specified for the design, material selection, manufacture, testing, marking and packaging of bonded flexible pipes, with reference to existing codes and standards where applicable. See API RP 17B for guidelines on the use of flexible pipes and ancillary components. 1.2 Products 1.2.1 This part of ISO 13628 applies to bonded flexible pipe assemblies, consisting of segments of flexible pipe body with end fittings attached to both ends. This part of ISO 13628 does not cover flexible pipes of unbonded structure. See ISO 13628-2 for guidance on unbonded flexible pipes. NOTE For the purposes of this provision, API Spec 17J[10] is equivalent to ISO 13628-2. 1.2.2 This part of ISO 13628 does not apply to flexible pipe ancillary components. Guidelines for ancillary components are given in API RP 17B. 1.2.3 This part of ISO 13628 can be applied to flexible pipes that include non-metallic reinforcing layers, though no effort was made to address the specific and unique technological aspects of this product. 1.2.4 This part of ISO 13628 can be applied to a bonded construction pipe that includes a material or layer construction that is covered in ISO 13628-2. 1.3 Applications 1.3.1 The applications addressed by this part of ISO 13628 are sweet and sour service production, including export and injection applications. Production products include oil, gas, water and injection chemicals. This part of ISO 13628 applies to both static and dynamic flexible pipes used as flowlines, risers, jumpers and offshore loading and discharge hoses. This part of ISO 13628 applies to pipes with a design pressure greater than or equal to 1,5 MPa (15 bar). This part of ISO 13628 can be used for lower design pressure pipes, though the requirements of these pipes have not been specifically addressed. Reference OCIMF[30] for guidelines on these pipes. 1.3.2 This part of ISO 13628 does not apply to flexible pipes for use in choke and kill line applications. See API Spec 16C for guidance on choke and kill line applications. This part of ISO 13628 can be applied to flexible pipes for pile hammer, gas flare, water supply and jetting applications, though no effort was made to address the specific and unique technological aspects relating to each of these requirements.

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 10: Specification for bonded flexible pipe

ISO 13628-8:2002/cor 1:2005 石油和天然气工业.水下生产系统的设计和操作.第8部分:水下生产系统上的遥控运载工具接口.技术勘误1

This is Technical Corrigendum 1 to ISO 13628-8-2002 (Petroleum and natural gas industries — Design and operation of subsea production systems — Part 8: Remotely Operated Vehicle (ROV) interfaces on subsea production systems)

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 8: Remotely Operated Vehicle (ROV) interfaces on subsea production systems; Technical Corrigendum 1

ISO 19900:2002 石油和天然气工业.近海结构的一般要求

This International Standard specifies general principles for the design and assessment of structures subjected to known or foreseeable types of actions. These general principles are applicable worldwide to all types of offshore structures including bottom-founded structures as well as floating structures and to all types of materials used including steel, concrete and aluminium. This International Standard specifies design principles that are applicable to the successive stages in construction (namely fabrication, transportation and installation), to the use of the structure during its intended life and to its decommissioning. Generally, the principles are also applicable to the assessment or modification of existing structures. Aspects related to quality control are also addressed. This International Standard is applicable to the design of complete structures including substructures, topsides structures, vessel hulls, foundations and mooring systems.

Petroleum and natural gas industries - General requirements for offshore structures

ISO 13628-5:2002 石油和天然气工业.水下采油系统的设计和操作.第5部分:水下缆线和管道

This part of ISO 13628 specifies requirements and gives recommendations for the design, material selection, manufacture, design verification, testing, installation and operation of subsea control systems, chemical injection, gas lift, utility and service umbilicals and associated ancillary equipment for the petroleum and natural gas industries. This part of ISO 13628 applies to umbilicals containing electrical conductors, optical fibres, thermoplastic hoses and metallic tubes, either alone or in combination. This part of ISO 13628 applies to umbilicals that are for static or dynamic service, and with routings of surface-surface, surface-subsea and subsea-subsea. This part of ISO 13628 does not apply to the associated component connectors, unless they affect the performance of the umbilical or that of its ancillary equipment.

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 5: Subsea umbilicals

ISO 13628-3:2000 石油和天然气工业 水下采油系统的设计和操作 第3部分:通流线系统

This part of ISO 13628 specifies requirements and gives recommendations for the design, fabrication and operation of TFL equipment and systems. The procedures and requirements presented are for the hydraulic servicing of downhole equipment, subsea tree and tubing hanger, and flowlines and equipment within the flowlines. This part of ISO 13628 primarily addresses TFL systems for offshore, subsea applications but it may also be used in other applications such as highly-deviated wells or horizontally-drilled wells. Subsea separation, boosting, metering and downhole pumps are outside the scope of this part of ISO 13628.

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 3: Through flowtime (TFL) systems

ISO 13628-2:2000 石油和天然气工业 海底生产系统的设计和操作 第2部分:用于海底和海上的挠性管系统

GB/T 21445 的本部分， 规定了挠性管在设计、选材、制造、测试、标记和包装方面的最低要求和建议， 并详细说明在安全以及尺寸和功能上可互换挠性管方面的技术要求和建议。 本部分适用于由在两端带有端部配件的挠性管管段组成的非粘合挠性管总成。 本部分不仅适用于无硫的产品，也是哟功能于含硫的产品， 包括用于输出和注入。采出的流体包括油、气、水和注入的化学药剂。本部分适用于作为流体管线、立管和跨接管线的静态和动态挠性管。 本部分不适用于粘合结构的挠性管， 也不适用于挠性管的附属构件。 不部分不适用于作为节流和压井管线的挠性管。 注：附录B给出抗弯加强器和弯曲限制器的指导， API RP 17B[1]中给出其他方面的指导。

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 2: Flexible pipe systems for subsea and marine applications

SY/T 10036-2001 海洋石油工程设计文件编制规程

本标准规定了海上油、气田工程设计文件的格式和编制方法。 本标准适用于海上油、气田工程设计文件的编制。

Regulations for Compilation of Offshore Oil Engineering Design Documents

ISO 13628-9:2000 石油和天然气工业 水下采油系统的设计和操作 第9部分:遥控设备干预系统

This part of ISO 13628 provides functional requirements and recommendations for ROT intervention systems and interfacing equipment on subsea production systems for the petroleum and natural gas industries. This part of ISO 13628 does not cover manned intervention and ROV-based intervention systems (e.g. for tie-in of sealines and module replacement). Vertical wellbore intervention, internal flowline inspection, tree running and tree running equipment are also excluded from this part of ISO 13628.

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 9: Remotely Operated Tools (ROT) intervention systems

ISO 13628-4:1999 石油和天然气工业 水下采油系统的设计和操作 第4部分:井口和采油树设备

1 This part of ISO 13628 specifies subsea copewellhead, conventional mudline wellhead, drill through mudline wellhead, conventional subsea trees and horizontal subsea trees. It also specifies the associated tooling necessary to handle, test and install the equipment. It also specifies the areas of design, material, welding, quality control (including factory acceptance testing), marking, storing and shipping for both individual sub-assemblies (used to build complete subsea tree assemblies) and complete subsea tree assemblies. Where applicable, this part of ISO 13628 may also be used for equipment on satellite, cluster arrangements and multiple well template applications. 2 Equipment which is within the scope of this part of ISO 13628 is listed as follows: a) Subsea trees — tree connectors and tubing hanger spools; — valves, valve blocks, and valve actuators; — chokes and choke actuators; — bleed, test and isolation valves; — TFL wye spool; — re-entry spool; — tree cap; — tree piping; — tree guide frames; — tree running tools; — tree cap running tools; — tree mounted flowline/umbilical connector; — control module/pod running/retrieval and testing tools; — flowline base running/retrieval tools; — tree mounted controls interfaces (instrumentation, sensors, hydraulic tubing/piping and fittings, electrical controls cable and fittings). b) Subsea wellheads — conductor housings; — wellhead housings; — casing hangers; — seal assemblies; — guidebases; — bore protectors and wear bushings; — corrosion caps. c) Conventional mudline suspension systems — wellheads; — running tools; — casing hangers; — casing hanger running tool; — tieback tools for subsea completion; — subsea completion adaptors for mudline wellheads; — tubing spools; — corrosion caps. d) Drill through mudline suspension systems — conductor housings; — surface casing hangers; — wellhead housings; — casing hangers; — annulus seal assemblies; — bore protectors and wear bushings; — abandonment caps. e) Tubing hanger systems — tubing hangers; — running tools. f) Miscellaneous equipment — flanged end and outlet connections; — clamp hub-type connections; — threaded end and outlet connections; — other end connections; — studs and nuts; — ring joint gaskets; — intervention equipment; — guide line establishment equipment. 3 Equipment which is beyond the scope of this part of ISO 13628 includes: — subsea wireline/coiled tubing BOPs; — workover and production risers; — control systems and control pods; — platform tiebacks; — primary protective structures; — subsea process equipment; — subsea manifolding; — subsea wellhead tools; — repair and rework; — multiple well template structures; — mudline suspension high pressure risers; — template piping; — template interfaces. 4 Equipment definitions are given in clause 3 and equipment use and function are explained in annexes A to F. Service conditions and product specification levels are given in clause 4. Critical components are those parts having requirements specified in this part of ISO 13628. Rework and repair of used equipment are beyond the scope of this part of ISO 13628.

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 4: Subsea wellhead and tree equipment

ISO 13628-1:1999 石油和天然气工业 水下采油系统的设计和操作 第1部分:一般要求和建议

Petroleum and natural gas industries - Design and operation of subsea production systems - Part 1: General requirements and recommendations

SY 6044-1994 浅海石油作业人员应急撤离条件

Emergency evacuation conditions for shallow sea oil workers

SY/T 5852-1993 海上气井完井测试技术规范

本标准规定了海上烃类气井完井现场测试和资料解释的技术规范。 本标准适用于海上天然气探井、评价井和生产井完井测试和资料解释。

Offshore Gas Well Completion Testing Technical Specifications