L92 电子设备用绝缘零件 标准查询与下载

GB/T 39975-2021 氮化铝陶瓷散热基片

本标准规定了氮化铝陶瓷散热基片的分类与标记、技术要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于LED、电子封装等领域用氮化铝陶瓷散热基片。其他用途的氮化铝陶瓷散热基片也可参照本标准。

Aluminum nitride ceramic dissipate heat substrates

GB/T 39950-2021 LED灯用氧化铝陶瓷散热元件

本标准规定了LED灯用氧化铝陶瓷散热元件的分类、标记、技术要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于LED灯用承载发光芯片、金属线路的氧化铝陶瓷散热元件。

Alumina ceramic heat radiating element for LED lamp

GB/T 39863-2021 覆铜板用氧化铝陶瓷基片

本标准规定了覆铜板用氧化铝陶瓷基片的技术要求、检测方法、检验规则、标志、包装、运输和贮存。本标准适用于覆铜板用氧化铝陶瓷基片的生产、销售和使用,其他片式氧化铝陶瓷也可参照使用。

Alumina ceramic substrate for copper clad laminate

GB/T 15750-1995 压电陶瓷材料老化性能试验规程

本标准规定了压电陶瓷材料时间老化、温度老化性能的试验方法。 本标准适用于压电陶瓷材料时间老化与温度老化性能的试验。

Test program for the ageing properties of piezoelectric ceramics

GB/T 13841-1992 电子陶瓷件表面粗糙度

本标准规定了电子陶瓷件表面粗糙度参数、参数值和对其要求的一般规则。 本标准主要适用于电子产品用电子陶瓷件表面粗糙度，其他产品用电子陶瓷件表面粗糙度，亦可参照应用。

Surface roughness for electronic ceramic parts

GB/T 12635-1990 碳膜电阻器用陶瓷基体

本标准规定了碳膜电阻器用陶瓷基体的外形结构尺寸、技术要求、试验方法、检验规则、标志、包装、贮存和运输。 本标准适用于碳膜电阻器用陶瓷基体（以下简称基体）。

Ceramic base body using in carbon film resistor

GB 12635-1990 碳膜电阻器用陶瓷基体

Ceramic substrate for carbon film resistors

GOST 32998.4-2014 绝缘玻璃装置. 密封层物理特性的测定方法

Insulating glass units. Methods for determining the physical characteristics of the sealing layer

GOST 30779-2014 绝缘玻璃装置. 生命周期的测定方法

Insulating glass units. Method for determination of life circle

UL 2097-2006 电子设备用双绝缘系统的参考标准

These requirements cover double insulation systems intended for use in ungrounded electronic equipment marked "Double Insulation," "Double Insulated," or with the double-insulation symbol intended to be employed in accordance with the National Electrical Code, ANSI/NFPA 70. Equipment marked "Double Insulation," "Double Insulated," or with the double-insulation symbol shall comply with the applicable requirements in this standard and in the standard covering the particular type of equipment - the end-product standard. In cases where the end-product standard contains requirements for double insulation, the end-product standard takes precedence. It is intended that the requirements in this standard be applied to end products marked as described unless the end-product standard specifies different requirements. These requirements were developed for categories that do not have double insulation requirements, to provide guidance about double insulation systems, and to promote consistent approaches to double insulation. Double insulation requirements for electronic equipment are applicable to the double insulation systems used in products contained in various end-product, component and systems standards. Guidelines and Applications for Double Insulation Systems for Electronic Equipment in Appendix a covers: a) Level of Protection Provided by Double Insulation, b) Methods to Address Product-Specific Double Insulation Requirements, and c) Guidelines for Including Double Insulation Requirements in an End-Product Standard. A product that contains features, characteristics, components, materials, or systems new or different from those covered by the requirements in this standard, and that involves a risk of fire, electric shock, or injury to persons shall be evaluated using the appropriate additional component and end-product requirements to determine that the level of safety as originally anticipated by the intent of this standard is maintained. A product whose features, characteristics, components, materials, or systems conflict with specific requirements or provisions of this standard shall not be judged to comply with this standard. Where appropriate, revision of requirements shall be proposed and adopted in conformance with the methods employed for development, revision, and implementation of this standard.

UL Standard for Safety Reference Standard for Double Insulation Systems for Use in Electronic Equipment Fourth Edition

SJ/T 11274-2002 推板式高温隧道电窑通用规范

本规范规定了推板式高温隧道电窑通用术语、产品分类型号及命名方法、技术要求、试验方法、验收方法及设备标志、包装、运输、贮存的基本要求。 本规范适用于电子行业各种型号规格的推板式高温隧道电窑，包括：在空气气氛或在保护气氛中烧结产品的导轨式窑、辊道一导轨式窑。其它行业类似设备亦可参照执行。

Generic specification for pusher type high temperature electro-heat tunnel kiln

SJ/T 11275-2002 卧式液相外延系统通用规范

本规范规定了卧式液相外延系统的术语、产品型号及命名方法、技术要求、试验方法、检验规则以及包裝、运输、贮存。 本规范适用于电子行业光电子器件研制、生产工艺中的卧式液相外延系统。其他行业的类似设备，亦可参照执行。

Generic specification for horizontal liquid phase epitaxial system

UL 2097-1999 电子设备用双绝缘系统的参考标准

Reference standard for duble insulation systems for use in electronic equipment

SJ/T 143-1996 被银陶瓷零件

本标准规定了被银陶瓷零件的要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于用烧渗法在陶瓷上被覆银层，用电镀法加厚的银铜层和用软焊料热浸(涂)锡的银-锡层、银-铜-锡层的被银陶瓷零件。

Silvered ceramic parts

SJ/T 10517-1994 塑料注射模模架

本标准规定了塑料注射模模架的10种基本组合形式及组合规格尺寸表等内容。 本标准适用于注射量为10kg以下注射机(含10kg注射机)用的、其周界尺寸为130mm×130mm～125mm×160mm的各种模具。

Mould bases of injection mould for plastic

UL 2097-1994 电气设备用双绝缘系统

Double insulation systems for use in electronic equipment

SJ/T 10516-1994 塑料注射模模架编号规则

本标准规定了塑料注射模模架的组合规格、结构型式代号、组合代号及模架组合的标记示例等内容。 本标准适用于塑料注射模各种型式模架组合的编号规则。

Numbering system for mould bases of injection mould for plastic

SJ/T 10520-1994 塑料注射模零件技术条件

本标准规定了塑料注射模零件技术要求、验收、包装、贮存、运输。 本标准适用于SJ/T 10519-1994《塑料注射模零件》所规定的零件技术条件。

Specifications for components of injection mould for plastic

SJ/T 10518-1994 塑料注射模模架技术条件

本标准规定了塑料注射模模架组合的技术要求、验收规则、包装、运输和贮存等内容。 本标准适用于塑料注射模模架组合的技术条件。

Specification for mould bases of injection mould for plastic

SJ/T 10519.1-1994 塑料注射模零件.模板

本标准规定了塑料注射模模板的结构尺寸、标记示例及技术要求。 本标准适用于塑料注射模各种模架和定模板、动模板、定模座板，动模座板。

Components of injection mould for plastics.Mould plates