Q08 标志、包装、运输、贮存 标准查询与下载

GB 9774-2002 水泥包装袋

本标准规定了水泥包装袋的技术要求、试验方法、检验规则、标志、运输、贮存和使用。本标准适用于装载质量不超过50 kg的各种类型的水泥包装袋。

Sacks for packing cement

GB/T 6382.2-1995 平板玻璃集装器具箱式集装器及其试验方法

本标准规定了平板玻璃箱式集装器（简称集装箱）的术语、分类、规格尺寸和质量、技术要求、试验方法及检验规则。 本标准适用于国内运输和储存平板玻璃用的集装箱。

Flat glass container--Box-type container and its test method

GB/T 6382.1-1995 平板玻璃集装器具架式集装器及其试验方法

本标准规定了平板玻璃架式集装器（简称集装架）的术语、分类、规格尺寸和质量、技术要求、试验方法和检验规则。 本标准适用于国内运输和储存平板玻璃用的集装架。

Flat glass container--Frame-type container and its test method

ASTM C387/C387M-11 砂浆和混凝土用混合材料干包装的标准规格

1.1 This specification covers the production, properties, packaging, and testing of packaged, dry, combined materials for concrete and mortars. The classifications of concrete and mortar covered are defined in Section 3. Note 18212;The scope of this standard does not cover mortars for unit masonry. Dry preblended mortars for unit masonry are covered by Specification . 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 The following safety hazards caveat pertains only to the test method portion of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Packaged, Dry, Combined Materials for Mortar and Concrete

ASTM C387/C387M-11b 混凝土和高强度灰浆用包装烘干和复合材料的标准规格

1.1 This specification covers the production, properties, packaging, and testing of packaged, dry, combined materials for concrete and high strength mortar. The classifications of concrete and mortar covered are defined in Section 3. Note 18212;The scope of this standard does not cover mortars for unit masonry. Dry preblended mortars for unit masonry are covered by Specification . 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Some values have only SI units because the inch-pound equivalents are not used in practice. 1.3 The following safety hazards caveat pertains only to the test method portion of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar

ASTM C387/C387M-11a 砂浆和混凝土包装,干燥,复合材料的标准规范

1.1 This specification covers the production, properties, packaging, and testing of packaged, dry, combined materials for concrete and mortars. The classifications of concrete and mortar covered are defined in Section 3. Note 18212;The scope of this standard does not cover mortars for unit masonry. Dry preblended mortars for unit masonry are covered by Specification . 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 The following safety hazards caveat pertains only to the test method portion of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Packaged, Dry, Combined Materials for Mortar and Concrete

ASTM C928/C928M-09 混凝土修补用干包装快硬胶结材料标准规范

1.1 This specification covers packaged, dry, cementitious mortar or concrete materials for rapid repairs to hardened hydraulic-cement concrete pavements and structures. Materials that contain organic compounds, such as bitumens, epoxy resins, and polymers, as the principal binder are not included. 1.1.1 Packaged, dry, concrete material contains aggregate of which at least 5 % by mass of the total mixture is retained on a 9.5-mm [3/8-in.] sieve. 1.1.2 Packaged, dry, mortar material contains aggregate of which less than 5 % by mass of the total mixture is retained on a 9.5-mm [3/8-in.] sieve. 1.2 Aqueous solutions, aqueous emulsions or dispersions may be included as components of the packaged materials. The manufacturer may specify that these liquids are to replace some or all of the mixing water. 1.3 Aggregates must be included as a component of the packaged materials. The manufacturer may recommend job site addition of specific amounts and types of additional aggregates to his product for some uses. However, such reformulated products are not within the scope of this specification. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 The following safety hazards caveat pertains to the test methods portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Packaged, Dry, Rapid-Hardening Cementitious Materials for Concrete Repairs

JC/T 694-2008 卫生陶瓷包装

本标准规定了卫生陶瓷包装的术语和定义、包装形式、包装材料、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于卫生陶瓷的包装。

Packaging for sanitary wares

ASTM C963-00(2012) 锁条衬垫的包装、识别、交货及储存的标准规范

1.1 This specification covers the packaging, identification, shipment, and storage of lock-strip gaskets and components that comply with Specification C542 and that are used in building walls that are not more than 15?? from a vertical plane.

Standard Specification for Packaging, Identification, Shipment, and Storage of Lock-Strip Gaskets

JC/T 534-1994 滑石粉包装用袋

Packaging bag for talcum powder

JC/T 513-1993 平板玻璃木箱包装

Wooden case packaging for plate glass

JC/T 512-1993 汽车安全玻璃包装

Packaging of automobile safety glass

JC/T 192-1981 石英玻璃验收规则、包装及保管方法

Specification for inspection, packaging and storage of quartz glass