S13 桥涵与隧道构件 标准查询与下载

GB/T 904-1994 铁路桥梁跨度系列

本标准规定了铁路桥梁跨度系列的尺寸。 本标准适用于标准轨距铁路简支式桥梁，其他式样桥梁亦应参照使用。

Railway bridge span series

TB/T 3561-2020 铁路桥梁黏滞阻尼器和速度锁定器

Railway bridge viscous dampers and speed locks

TB/T 2349-2016 铁路钢桥连接疲劳试验方法

Fatigue test method for railway steel bridge connections

TB/T 3193-2016 铁路工程预应力筋用夹片式 锚具、夹具和连接器

本标准规定了夹片式锚具（含夹片式低回缩锚具）、夹具和连接器术语和定义、产品的代号与标记、技术要求、检验方法、检验规则和标志、包装、运输、贮存。 本标准适用于铁路工程预应力混凝土结构中使用的锚固直径为15.20 mm钢绞线的夹片式锚具、夹具和连接器。

Anchorage, grip and coupler for prestressing tendons in railway construction

TB/T 3435-2016 铁路混凝土桥梁梁端防水装置

本标准规定了铁路混凝土桥梁梁端防水装置的术语和定义，规格、分类、型号编制规则及结构形式，技术要求，检验方法，检验规则，标志、包装、储存和运输。 本标准适用于由异型型材和防水橡胶带等部件组成的、伸缩量为30 mm~200 mm的高速铁路混凝土桥梁梁端防水装置，其他铁路混凝土桥梁梁端防水装置可参照使用。

Waterproof device for railway concrete bridge joint

GOST 33797-2016 轨道交通架空接触网刚性入口横梁通用规格

Cross beams of rigid portals for overhead contact line of rail transport. General specifications

TB/T 3354-2014 铁路隧道排水板

本标准规定了铁路隧道排水板的分类和标记，技术要求，检验方法，检验规则，合格证、包装、运输和贮存。 本标准适用于铁路隧道工程用排水板。

Railway tunnel drainage board

TB/T 3353-2014 铁路隧道钢筋混凝土管片

本标准规定了铁路隧道预制钢筋混凝土衬砌管片(以下简称管片)的术语和定义、分类与标记、原材料、制作要求、技术要求、检验方法、检验规则、标志与出厂质量证明书、贮存与运输。本标准适用于铁路隧道工程掘进机法、盾构法施工用钢筋混凝土衬砌管片。

Reinforced concrete segments for railway tunnel

TB/T 3356-2014 预应力中空锚杆

本标准规定了铁路工程预应力中空锚杆的术语，标记与规格，技术要求，检验方法，检验规则，标志、包装和贮存。本标准适用于铁路工程中使用的预应力中空锚杆。

Prestressed anchor bolt with hollow bar

Q/CR 9300-2014 铁路桥涵极限状态法设计暂行规范

本规范适用于铁路桥涵结构设计。跨度168 m以上钢桥及128 m以上混凝土桥,墩高大于50 m桥墩,除满足本规范外,尚应进行专门研究。

Interim Code for Limit State Design of Railway Bridge and Culvert

TB/T 2331-2013 铁路桥梁盆式支座

本标准规定了铁路桥梁盆式支座的规格、分类、型号、结构形式、技术要求、检验方法、检验规则、标志、包装、储存和运输、安装和养护、调高及保修期。本标准适用于竖向设计承载力为1 000 kN ~ 60 000 kN、地震动峰值加速度值A不大于0. 3g地区使用的铁路桥梁盆式支座,其他桥梁及结构工程用盆式支座可参考使用。

Pot bearings for railway bridges

TB/T 3320-2013 铁路桥梁球型支座

本标准规定了铁路桥梁球型支座的规格与分类, 结构形式和型号,技术要求,检验方法,检验规则,标志、包装、储存和运输,安装和养护。本标准适用于竖向设计承载力为1 000 kN ~ 100 000 kN 的铁路桥梁球型支座,其他桥梁及结构工程用球型支座可参考使用。

Spherical bearings for railway bridges

EN 13145:2001+A1:2011 铁路应用.轨道.枕木和垫块

This European Standard defines wood species, quality requirements, origin, manufacturing conditions, forms, dimensions and tolerances as well as the durability and preservation of wood sleepers and bearers for use in railway tracks. It does not cover specific finishing processes that may be required by the customer. It does not apply to other track timbers.

Railway applications - Track - Wood sleepers and bearers

TB/T 2965-2011 铁路混凝土桥面防水层技术条件

本标准规定了铁路桥梁有砟、无砟混凝土桥面有保护层的防水层的原材料、防水层铺设、保护层、质量检查以及保修期要求。 本标准适用于铁路桥梁有砟、无砟混凝土桥面有保护层的防水层。

Technical speecification for waterproof layer of railway concrete bridge

EN 13261:2009+A1:2010 铁路应用.轮组和转向架.车桥.产品要求

This European Standard specifies the characteristics of axles for use on European networks. It defines characteristics of forged or rolled solid and hollow axles, made from vacuum-degassed steel grade EA1N1 that is the most commonly used grade on European networks. For hollow axles, this standard applies only to those that are manufactured by machining of a hole in a forged or rolled solid axle In addition, the particular characteristics for axles in grade EA1T1 and EA4T1 are given in Annex A. Two categories of axle are defined, category 1 and category 2. Generally, category 1 is chosen when the operational speed is higher than 200 km/h. This standard is applicable to axles that are designed in accordance with the requirements of EN 13103 and EN 13104. NOTE Different values for some characteristics may be agreed if a particular process of fabrication (e. g. cold rolling, shot peening, shot peening, steel cleanliness, reduction ratio, improved material properties from melting and heat treatment processes, etc.) has an influence on them.

Railway applications - Wheelsets and bogies - Axles - Product requirements

EN 13260:2009+A1:2010 铁路应用.轮组和转向架.轮组.产品要求

This European Standard specifies the characteristics of new wheelsets for use on European networks: This standard is applicable to wheelsets comprising elements that conform to the following European Standards: EN 13262 for wheels; EN 13261 for axles; This standard is not fully applicable to wheelsets undergoing maintenance. Some characteristics are given as a function of a category 1 or of a category 2. Category 2 can be divided into sub-categories (2a and 2b) to specify certain characteristics. Category 1 is generally chosen when the operating speed exceeds 200 km/h. The wheelset then comprises wheels and axle of category 1 as specified in EN 13262 for the wheels and EN 13261 for the axles.

Railway applications - Wheelsets and bogies - Wheelsets - Product requirements

EN 15427:2008+A1:2010 铁路应用.轮/轨摩擦管理.轮缘润滑

This document is limited to specifying the requirements when applying lubricants to the wheel-rail interface between the wheel flange and the rail gauge corner (active interface) either directly or indirectly to the wheel flange or to the rail, and includes both trainborne and trackside solutions. This document defines: the characteristics that systems of lubrication of the wheel-rail interface shall achieve, together with applicable inspection and test methods to be carried out for verification; all relevant terminology which is specific to the lubrication of the wheel-rail interface.

Railway applications - Wheel/rail friction management - Flange lubrication

TB/T 3229-2010 铁路线路作业移动式照明设备

本标准规定了铁路线路作业移动式照明设备的术语和定义、结构、主要技术参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于铁路线路作业移动式照明设备。

Mobile lighting equipment for track maintenance works

UIC R 776-2-2009 基于火车,铁轨和桥梁相互作用现象的铁路大桥用设计要求

The procedures for verifying the strength of railway bridges are covered by detailed and comprehensive rules of calculation already in existence. In contrast, serviceability limit states, notably deformation ELS, are described only in network calculation rules or in UIC leaflets. In essence, bridges are deformable structures. These deformations must be controlled all the more accurately as trains travel at high, and very high speeds. The purpose of this leaflet is to specify the design requirements for rail-bridges as regards train/track/bridge interaction phenomena and in particular speed, thereby taking into account bridge resonance phenomena. It outlines the corresponding draft criteria and provides information on the phenomena to be controlled as well as the appropriate procedures for verifying the structures. This leaflet should be used in conjunciton with UIC Leaflet 776-1.

Design requirements for rail-bridges based on interaction phenomena between train,track and bridge

TB 10212-2009 铁路钢桥制造规范

本规范适用于铁路钢桥制造及质量检验。对于本规范未涉及的新技术、新结构、新材料、新工艺,制造中应进行试验,并根据试验结果确定所必须补充的标准。

Code for fabrication of railway steel bridge