T06 工艺与工装 标准查询与下载

SN/T 4580.1-2016 进口汽车制造行业成套设备检验技术要求 第1部分：焊装工艺设备

Technical requirements for inspection of complete sets of equipment for the imported automobile manufacturing industry Part 1: Welding process equipment

QC/T 721-2013 汽车用非电解锌片涂层

本标准规定了汽车用非电解锌片涂层的一般性能、防护等级要求及图样标记。本标准适用于汽车用钢铁、铝及锌合金零件的表面防护。

Non-electrolytically applied zinc flake coatings for automobile

SAE J1974-2013 汽车应用装饰性电镀规范

This document has been declared ""Stabilized"" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. Detailed in this SAE Recommended Practice are interior and exterior bright or electrolytically colored anodized aluminum automotive components in the form of seat trim, dashboard, window or side body moldings, bumpers, wheels, rocker panel, etc.

Decorative Anodizing Specification for Automotive applications

SAE J493-2013 杆端和U形夹销

This document has been declared ""Stabilized"" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. Material--SAE 1010 or SAE 1111 steel or equivalent. Clevis pins shall be supplied either soft or cyanide hardened as specified. Clevis pins must be free from burrs, loose scale, sharp edges, and all other defects that might affect their serviceability. General tolerances for all dimensions are plus or minus 0.010 unless otherwise specified.

Rod Ends and Clevis Pins

SAE J207-2012 汽车装饰物和配件上的镍和铬电镀标准

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This standard covers requirements for several types and grades of electrodeposited nickel/chromium coatings on ferrous or copper alloy basis metals and copper/nickel/chromium on zinc or aluminum alloys for the finishing and corrosion protection of decorative ornamentation and hardware of motor vehicles and marine controls and fittings. Four grades of coatings are provided to correlate with the service conditions under which each is expected to provide satisfactory performance, namely: very severe, severe, moderate, and mild. Definitions and typical examples of these service conditions are provided in Appendix A. Information contained in this document generally conforms to the information contained in ASTM B 46, Specification for Electrodeposited coatings of nickel plus Chromium.

Electroplating of Nickel and Chromium on Metal parts Automotive ornamentation and Hardware

SAE J449-2011 表面纹理控制

SAE J448, Surface Texture, has been set up for precision reference specimens using a controlled surface profile to obtain reproducible roughness values. These specimens are for instrument calibration. Appropriate symbols for roughness, waviness, and lay have also been standardized (ASA B46.1-1962 and SAE J448). For production control, especially from one geographical location to another, means are required to facilitate the inspection of surface characteristics called for by specifications which include not only roughness but profile waviness and lay. In order to integrate the requirements of the designer with the actual production of surfaces, a second grade of control standards must be adopted which will be functional in nature for the specific product being manufactured. These control standards may be Calibrated pilot specimens (actual parts with satisfactory texture) or Roughness comparison Specimens (ASA B46.1-1962). This SAE Recommended practice describes the usage of these control standards.

Surface Texture Control

SAE J1959-2003 防蚀剂对车身底部车辆腐蚀保护,代替J1969 1998年6月

This specification covers underbody corrosion preventive compounds for application to vehicle underbodies. This document contains reference to certain automotive industry tests, it only reflects interest in selecting what is felt to be the easiest and most useful tests for evaluation of rust corrosion preventatives, and does not suggest that the tests of other vehicle manufacturers are of lesser value or validity.

Corrosion Preventive Compound, Underbody Vehicle Corrosion Protection Superseding J1969 JUN1998

DB53/ 060-2002 手扶拖拉机转向灯、制动灯安装验收技术规范

本标准规定了道路行驶的各类手扶拖拉机运输机组（含折腰转向盘式）、挂车的转向灯、制动灯的要求、试验方法及安装验收规范。本标准适用于配置有交流发电机的手扶拖拉机运输机组（含折腰转向盘式）、挂车的转向灯、制动灯或在用运输机组增配转向灯、制动灯。

Technical specification for installation and acceptance of steering lights and brake lights of walking tractors

SAE J2441-2000 喷丸加工

This SAE Standard covers the engineering requirements for peening surfaces of parts by impingement of metallic shot, glass beads, or ceramic shot. To induce residual compressive stress in surface layers of parts, thereby increasing fatigue strength and resistance to stress-corrosion cracking.

Shot Peening

SAE J1134-2000 SAE 节点安装

This SAE Recommended Practice establishes a single bolt pattern for both No. 1 and 2 clutch housings. These four bolt patterns are designated to give commonality of mounting brackets in existing frame rails. The 420 mm (16.5 in) span, pad face to pad face, allows the ease of installation in existing frame rail widths. This is also the minimum spacing which will accommodate commonly used clutches.

SAE Nodal Mount

SAE J533-1999 管扩口

This SAE Standard covers specifications for 37-degree and 45-degree single and double flares for tube ends intended for use with 37- degree flared tube fittings and 45-degree flared or inverted flared tube fittings, respectively.

Flares for Tubing

DB52/T 422-1999 贵州常用汽车维护工艺规范

本标准规定了汽车各级维护周期、作业要求和质量保证。 本标准适用于汽车维修企业和运输业主。

Guizhou common vehicle maintenance process specification

ARMY MIL-DTL-46735 C-1998 汽车装配绞车滚筒

This specification covers requirements for power operated spur planetary and planetary geared, heavy duty, drum type winches for use on military combat and tactical transport vehicles. The winches are driven from the vehicle hydraulic system.

WINCH DRUM: VEHICLE MOUNTING

SAE J490-1996 球头

This SAE Standard covers the general and dimensional data for various types of ball joints with inch threads commonly used on control linkages in automotive, marine, and construction and industrial equipment applications. Inasmuch as the load carrying and wear capabilities of ball joints vary considerably with their design and fabrication, it is suggested that the manufacturers be consulted in regard to these features and for recommendations relating to application of the different types and styles available. The inclusion of dimensional data in this standard is not intended to imply that all the products described are stock production sizes. Consumers are requested to consult with manufacturers concerning availability of stock production parts.

Ball Joints

SAE J2254-1995 流体动力管道清洗工艺

The procedures and guidelines detailed in this SAE information Report provide various techniques and processes to properly clean fluid power piping prior to assembly and operation. There are two recommended processes, pickling and flushing. Each procedure will remove particulate contaminates if properly applied.

Fluid Power Piping Cleaning Process

SAE J447-1995 汽车车身和底盘部件的防腐

This SAE Information Report provides automotive engineers with the basic principles of corrosion, design guidelines to minimize corrosion, and a review of the various materials, treatments, and processes available to inhibit corrosion of both decorative and functional body and chassis components.

Prevention of Corrosion of Motor Vehicle Body and Chassis Components

SAE J415-1995 热处理术语定义

(These definitions were prepared by the Joint Committee on definitions of Terms Relating to Heat Treatment appointed by the american society for Testing and Materials, The American Society for metals, the american Foundrymens Association, and the SAE.) This SAE revision emphasizes the terms used in heat treating ferrous alloys, but also includes for reference some non-ferrous definitions at the end of the document. This glossary is not intended to be a specification, and it should not be interpreted as such. Since this is intended to be strictly a set of definitions, temperatures have been omitted purposely

Definition of Heat Treating Terms

BS AU 251:1994 汽车叠层挡风玻璃检修器具的操作规范

Includes materials for making windscreen repairs in accordance with BS AU 242:1991.

Specification for performance of automotive laminated windscreen repair systems

SAE J1974-1993 汽车应用装饰性电镀规范的推荐实施规程.1993年6月

Detailed in this SAE Recommended Practice are interior and exterior bright or electrolytically colored anodized aluminum automotive components in the form of seat trim, dashboard, window or side body moldings, bumpers, wheels, rocker panel, etc.

Decorative Anodizing Specification for Automotive Applications, Recommended Practice June 1993

ASTM D5066-91(2011) 在喷涂汽车涂料的生产条件下测定转换效率的标准试验方法

This test method is specifically directed at the spray painting of automobile car and light duty truck bodies. The general principles are applicable to the painting of other automotive parts. This test method may also be used to measure transfer efficiency in full-sized painting facilities simulating production conditions and operations.1.1 This test method covers procedures for determination of the transfer efficiency (using a weight method) under production conditions for in-plant spray application of automotive paints as outlined in Section 18 of EPA 450/3-88-018. 1.2 The transfer efficiency is calculated from the weight of the paint solids sprayed and that deposited on the painted part. The recommended approach involves painting the part directly. Also described is an alternative approach for painting parts covered with aluminum foil. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in 10.1.8.1.

Standard Test Method for Determination of the Transfer Efficiency Under Production Conditions for Spray Application of Automotive Paints-Weight Basis