T10 汽车发动机综合 标准查询与下载

GB/T 28957.1-2023 道路车辆 用于滤清器评定的试验粉尘 第1部分：氧化硅试验粉尘

Test dusts for filter evaluation in road vehicles Part 1: Silica test dusts

GB/T 37154-2018 燃料电池电动汽车 整车氢气排放测试方法

Fuel cell electric vehicles—Test methods of hydrogen emission

GB/T 34600-2017 汽车零部件再制造产品技术规范 点燃式、压燃式发动机

The technical specification for remanufacturing of automotive components—Spark and compression ignition engines

GB/T 34593-2017 燃料电池发动机氢气排放测试方法

Test methods of hydrogen emission for fuel cell engine

GB/T 32231-2015 全地形车发动机通用技术条件

本标准规定了全地形车发动机的术语和定义、要求、试验方法、检验规则、标志、使用说明书、包装、运输及贮存。 本标准仅适用于GB/T 24936中所定义的内燃机式全地形车所使用的发动机(以下简称“发动机”)。

General technical specifications of engine used for all-terrain vehicles

GB/T 28957.1-2012 道路车辆 用于滤清器评定的试验粉尘 第1部分：氧化硅试验粉尘

GB/T 28957的本部分规定了用亚利桑那沙漠沙粒制造的四个等级的试验粉尘和BF氧化硅系列的两种试验粉尘的颗粒尺寸分布界限和化学成分、本部分适用于对道路车辆用滤清器滤清器的性能测定,也适用于一般用途的内燃机用滤清器的性能测定和轴承、密封件等部件的磨损研究、

Road vehicles.Test dust for filter evaluation.Part 1:Silicon dioxide test dust

GB/T 28674-2012 汽车零部件再制造产品技术规范.转向器

本标准规定了齿轮齿条式、循环球式机械和液压助力转向器再制造术语和定义，拆解、分类与清洗，检修与修复，总成装配要求，性能要求和试验方法，检验规则，标识与包装等 。 本标准适用于齿轮齿条式、循环球式机械和液压助力转向器的再制造。 本标准不适用于电液伺服转向器和电子转向器。 本标准不适用于发生过火灾或碰撞事故的转向器。

The technical specifications for remanufacturing of automotive components.Steering gear

GB/T 19055-2003 汽车发动机可靠性试验方法

本标准规定了汽车发动机在台架上整机的一般可靠性试验方法，其中包括负荷试验规范(如交变负荷、混合负荷和全速全负荷)、冷热冲击试验规范及可靠性评定方法。 本标准适用于乘用车、商用车的水冷发动机，不适用于摩托车及拖拉机用发动机。该类发动机属往复式、转子式，不含自由活塞式。其中包括点燃机及压燃机；二冲程机及四冲程机；非增压机及增压机(机械增压及涡轮增压、水对空及空对空中冷)；适用于燃用汽油、柴油、天然气、液化石油气和醇类等燃料的发动机。 新设计或重大改进的汽车发动机定型、转厂生产的发动机认证以及现生产的发动机质量检验均可按本标准规定的方法进行可靠性试验。 本标准还可作为发动机制造厂和汽车制造厂之间交往的技术依据。

Reliability test methods for motor vehicle engines

GB/T 18297-2001 汽车发动机性能试验方法

本标准规定了汽车用发动机性能台架试验方法，其中包括各种负荷下的动力性及经济性试验方法，无负荷下的起动、怠速、机械损失功率试验方法以及有关气缸密封性的活塞漏气量及机油消耗量试验方法等，用来评定汽车发动机的性能。 本标准适用于轿车、载货汽车及其他陆用车辆的内燃机，不适用于摩托车及拖拉机用内燃机。该内燃机属往复式、转子式，不含自由活塞式。其中包括点燃及压燃机、二冲程及四冲程机、非增压及增压机（机械增压、涡轮增压及中冷）、水冷及风冷机。 凡新设计及有重大改进的发动机定型试验、转产生产的发动机验证试验以及现生产的发动机质量检验试验等，均按本标准规定的方法进行。 本标准还可作发动机制造厂和汽车制造厂之间交往的技术依据。

Performance test code for road vehicle engines

GB/T 17692-1999 汽车用发动机净功率测试方法

本标准规定了汽车用发动机净功率测量方法。 本标准适用于由制造厂提出M和N类汽车用发动机净功率相对于转速变化的曲线。 本标准适用于往复活塞发动机（点燃式或压燃式）或转子发动机（点燃式或压燃式），但不包括自由活塞发动机。

Measurement methods of net power for automotive engines

GB/T 12782-1991 汽车采暖性能试验方法

本标准规定了汽车采暖性能要求和试验方法。 本标准适用于各种类型汽车。

Motor vehicle--Heating performance--Test method

QC/T 1145-2021 柴油/甲醇双燃料发动机技术条件

Diesel/methanol dual fuel engine technical conditions

EN 16905-4:2017 燃气吸热式发动机驱动的热泵 第4部分：测试方法

This European Standard specifies the requirements, test methods and test conditions for the rating and performance calculation of air conditioners and heat pumps using either air, water or brine as heat transfer media, with gas-fired endothermic engine driven compressors when used for space heating, cooling and refrigeration, hereafter referred to as "GEHP appliance". This European Standard only applies to appliances with a maximum heat input (based on net calorific value) not exceeding 70 kW at standard rating conditions. This European Standard only applies to appliances under categories I2H, I2E, I2Er, I2R, I2E(S)B, I2L, I2LL, I2ELL, I2E(R)B, I2ESi, I2E(R), I3P, I3B, I3B/P, II2H3+, II2Er3+, II2H3B/P, II2L3B/P, II2E3B/P, II2ELL3B/P, II2L3P, II2H3P, II2E3P and II2Er3P according to EN 437. This European Standard only applies to appliances having: a) gas fired endothermic engines under the control of fully automatic control systems; b) closed system refrigerant circuits in which the refrigerant does not come into direct contact with the fluid to be cooled or heated; c) where the temperature of the heat transfer fluid of the heating system (heating water circuit) does not exceed 105 °C during normal operation; d) where the maximum operating pressure in the: 1) heating water circuit (if installed) does not exceed 6 bar; 2) domestic hot water circuit (if installed) does not exceed 10 bar. This European Standard applies to appliances only when used for space heating or space cooling or for refrigeration, with or without heat recovery. The appliances having their condenser cooled by air and by the evaporation of external additional water are not covered by this European Standard. Packaged units, single split and multisplit systems are covered by this European Standard. Single duct and double duct units are covered by this European Standard. The above appliances can have one or more primary or secondary functions. This European Standard is applicable to appliances that are intended to be type tested. Requirements for appliances that are not type tested would need to be subject to further consideration. In the case of packaged units (consisting of several parts), this European Standard applies only to those designed and supplied as a complete package. NOTE All the symbols given in this text are used regardless of the language used. EN 16905-4 This part of the EN 16905 series specifies the test methods for gas-fired endothermic engine driven heat pumps for heating and/or cooling mode including the engine heat recovery.

Gas-fired endothermic engine driven heat pumps - Part 4: Test methods

EN 16905-1:2017 燃气吸热发动机驱动的热泵.第1部分:术语和定义

EN 16905 series This European Standard specifies the requirements, test methods and test conditions for the rating and performance calculation of air conditioners and heat pumps using either air, water or brine as heat transfer media, with gas-fired endothermic engine driven compressors when used for space heating, cooling and refrigeration, hereafter referred to as "GEHP appliance". This European Standard only applies to appliances with a maximum heat input (based on net calorific value) not exceeding 70 kW at standard rating conditions. This European Standard only applies to appliances under categories I2H, I2E, I2Er, I2R, I2E(S)B, I2L, I2LL, I2ELL, I2E(R)B, I2ESi, I2E(R), I3P, I3B, I3B/P, II2H3+, II2Er3+, II2H3B/P, II2L3B/P, II2E3B/P, II2ELL3B/P, II2L3P, II2H3P, II2E3P and II2Er3P according to EN 437. This European Standard only applies to appliances having: a) gas fired endothermic engines under the control of fully automatic control systems; b) closed system refrigerant circuits in which the refrigerant does not come into direct contact with the fluid to be cooled or heated; c) where the temperature of the heat transfer fluid of the heating system (heating water circuit) does not exceed 105 °C during normal operation; d) where the maximum operating pressure in the: 1) heating water circuit (if installed) does not exceed 6 bar 2) domestic hot water circuit (if installed) does not exceed 10 bar. This European Standard applies to appliances only when used for space heating or space cooling or for refrigeration, with or without heat recovery. The appliances having their condenser cooled by air and by the evaporation of external additional water are not covered by this European Standard. Packaged units, single split and multisplit systems are covered by this European Standard. Single duct and double duct units are covered by this European Standard. The above appliances can have one or more primary or secondary functions. This European Standard is applicable to appliances that are intended to be type tested. Requirements for appliances that are not type tested would need to be subject to further consideration. In the case of packaged units (consisting of several parts), this European Standard applies only to those designed and supplied as a complete package. NOTE All the symbols given in this text are used regardless of the language used. EN 16905-1 This part of EN 16905 series specifies the terms and definitions of gas-fired endothermic engine driven heat pumps for heating and/or cooling mode including the engine heat recovery.

Gas-fired endothermic engine driven heat pumps - Part 1: Terms and definitions

EN 16905-3:2017 燃气吸热发动机驱动热泵.第3部分:试验条件

EN 16905 series This European Standard specifies the requirements, test methods and test conditions for the rating and performance calculation of air conditioners and heat pumps using either air, water or brine as heat transfer media, with gas-fired endothermic engine driven compressors when used for space heating, cooling and refrigeration, hereafter referred to as "GEHP appliance". This European Standard only applies to appliances with a maximum heat input (based on net calorific value) not exceeding 70 kW at standard rating conditions. This European Standard only applies to appliances under categories I2H, I2E, I2Er, I2R, I2E(S)B, I2L, I2LL, I2ELL, I2E(R)B, I2ESi, I2E(R), I3P, I3B, I3B/P, II2H3+, II2Er3+, II2H3B/P, II2L3B/P, II2E3B/P, II2ELL3B/P, II2L3P, II2H3P, II2E3P and II2Er3P according to EN 437. This European Standard only applies to appliances having: a) gas fired endothermic engines under the control of fully automatic control systems; b) closed system refrigerant circuits in which the refrigerant does not come into direct contact with the fluid to be cooled or heated; c) where the temperature of the heat transfer fluid of the heating system (heating water circuit) does not exceed 105 °C during normal operation; d) where the maximum operating pressure in the 1) heating water circuit (if installed) does not exceed 6 bar; 2) domestic hot water circuit (if installed) does not exceed 10 bar. This European Standard applies to appliances only when used for space heating or space cooling or for refrigeration, with or without heat recovery. The appliances having their condenser cooled by air and by the evaporation of external additional water are not covered by this European Standard. Packaged units, single split and multisplit systems are covered by this European Standard. Single duct and double duct units are covered by this European Standard. The above appliances can have one or more primary or secondary functions. This European Standard is applicable to appliances that are intended to be type tested. Requirements for appliances that are not type tested would need to be subject to further consideration. In the case of packaged units (consisting of several parts), this European Standard applies only to those designed and supplied as a complete package. NOTE All the symbols given in this text are used regardless of the language used. EN 16905-3 This part of the EN 16905 series specifies the test conditions for the rating of energy parameters of gas-fired endothermic engine driven heat pumps for heating and/or cooling mode including the engine heat recovery.

Gas-fired endothermic engine driven heat pumps - Part 3: Test conditions

EN 16905-5:2017 燃气吸热发动机驱动热泵.第5部分:加热和冷却模式季节性性能的计算

This European Standard specifies the requirements, test methods and test conditions for the rating and performance calculation of air conditioners and heat pumps using either air, water or brine as heat transfer media, with gas-fired endothermic engine driven compressors when used for space heating, cooling and refrigeration, hereafter referred to as "GEHP appliance". This European Standard only applies to appliances with a maximum heat input (based on net calorific value) not exceeding 70 kW at standard rating conditions. This European Standard only applies to appliances under categories I2H, I2E, I2Er, I2R, I2E(S)B, I2L, I2LL, I2ELL, I2E(R)B, I2ESi, I2E(R), I3P, I3B, I3B/P, II2H3+, II2Er3+, II2H3B/P, II2L3B/P, II2E3B/P, II2ELL3B/P, II2L3P, II2H3P, II2E3P and II2Er3P according to EN 437. This European Standard only applies to appliances having: a) gas fired endothermic engines under the control of fully automatic control systems; b) closed system refrigerant circuits in which the refrigerant does not come into direct contact with the fluid to be cooled or heated; c) where the temperature of the heat transfer fluid of the heating system (heating water circuit) does not exceed 105 °C during normal operation; d) where the maximum operating pressure in the: 1) heating water circuit (if installed) does not exceed 6 bar, 2) domestic hot water circuit (if installed) does not exceed 10 bar. This European Standard applies to appliances only when used for space heating or space cooling or for refrigeration, with or without heat recovery. The appliances having their condenser cooled by air and by the evaporation of external additional water are not covered by this European Standard. Packaged units, single split and multisplit systems are covered by this European Standard. Single duct and double duct units are covered by this European Standard. The above appliances can have one or more primary or secondary functions. This European Standard is applicable to appliances that are intended to be type tested. Requirements for appliances that are not type tested would need to be subject to further consideration. In the case of packaged units (consisting of several parts), this European Standard applies only to those designed and supplied as a complete package. NOTE All the symbols given in this text are used regardless of the language used. EN 16905-5 This part of the EN 16905 series specifies the calculation of seasonal performance factor for gas-fired endothermic engine driven heat pumps for heating and/or cooling mode including the engine heat recovery.

Gas-fired endothermic engine driven heat pumps - Part 5: Calculation of seasonal performances in heating and cooling mode

EN 16942:2016 燃料.车辆兼容性的识别.消费者信息的图解表示法

This European Standard lays down harmonized identifiers for marketed liquid and gaseous fuels. The requirements in this standard are to complement the informational needs of users regarding the compatibility between the fuels and the vehicles that are placed on the market. The identifier is intended to be visualized at dispensers and refuelling points, on vehicles, in motor vehicle dealerships and in consumer manuals as described in this document. Marketed fuels include for example petroleum-derived fuels, synthetic fuels, biofuels, natural gas, liquefied petroleum gas, hydrogen and biogas and blends of the aforementioned delivered to mobile applications.

Fuels - Identification of vehicle compatibility - Graphical expression for consumer information

ISO 17447-1:2015 道路车辆. 带锥形阀座和气缸头罩的电热塞. 第1部分: 金属护套型电热塞的基本特征和尺寸

Road Vehicles - Glow-plugs with conical seating and their cylinder head housing - Part 1: Basic characteristics and dimensions for metal-sheath-type glow-plugs

ISO 17447-3:2015 道路车辆. 带锥形阀座和气缸头罩的电热塞. 第3部分: 试验和要求

This part of ISO 17447 specifies general requirements and test methods for sheath-type glow-plugs. Detailed test condition(s) and/or requirement(s) are agreed between the glow-plug manufacturers and the engine manufacturer. It is applicable to glow-plugs conforming to ISO 17447-1 and ISO 17447-2, used in diesel (compression ignition) engines.

Road Vehicles - Glow-plugs with conical seating and their cylinder head housing - Part 3: Tests and requirements

ISO 17447-2:2015 道路车辆. 带锥形阀座和气缸头罩的电热塞. 第2部分: 陶瓷护套型电热塞的基本特征和尺寸

This part of ISO 17447 specifies the main properties and dimensions of ceramic-sheath-type glowplugs, including the terminals and the dimensions of their cylinder head housings, for use with diesel (compression ignition) engines.

Road Vehicles - Glow-plugs with conical seating and their cylinder head housing - Part 2: Basic characteristics and dimensions for ceramic-sheath-type glow-plugs