T85 电子、电气设备 标准查询与下载

GB/T 37338-2019 电动摩托车和电动轻便摩托车用仪表

Instrumentation for electric motorcycles and mopeds

GB/T 36672-2018 电动摩托车和电动轻便摩托车用锂离子电池

Lithium-ion battery for electric mopeds and motorcycles

GB 18100-2000 两轮摩托车及轻便摩托车照明和光信号装置的安装规定

本标准规定了两轮摩托车及轻便摩托车照明和光信号装置的安装一般技术要求、特殊规定、试验方法及检验规则等。 本标准适用于两轮摩托车及轻便摩托车（L1、L3类）。

Provisions for installation of two wheel motorcycle and moped lighting and light-signalling devices

QC/T 792-2022 电动摩托车和电动轻便摩托车驱动用电机及其控制器

Motors and controllers for driving electric motorcycles and electric mopeds

QC/T 1152-2021 电动摩托车和电动轻便摩托车用DC/DC变换器技术条件

Technical specifications for DC/DC converters for electric motorcycles and electric mopeds

QC/T 417-2021 摩托车和轻便摩托车用电线束总成

Electrical wiring harness assemblies for motorcycles and mopeds

QC/T 1094-2018 摩托车起动用锂离子电池通用技术条件

General technical conditions for lithium-ion batteries for motorcycle starters

ISO 18243:2017 电动助力车和摩托车. 锂离子电池系统的试验规范和安全要求

This document specifies the test procedures for lithium-ion battery packs and systems used in electrically propelled mopeds and motorcycles. The specified test procedures enable the user of this document to determine the essential characteristics on performance, safety and reliability of lithium-ion battery packs and systems. The user is also supported to compare the test results achieved for different battery packs or systems. This document enables setting up a dedicated test plan for an individual battery pack or system subject to an agreement between customer and supplier. If required, the relevant test procedures and/or test conditions of lithium-ion battery packs and systems are selected from the standard tests provided in this document to configure a dedicated test plan. NOTE 1 Electrically power-assisted cycles (EPAC) cannot be considered as mopeds. The definition of electrically power-assisted cycles can differ from country to country. An example of definition can be found in the EU Directive 2002/24/EC. NOTE 2 Testing on cell level is specified in IEC 62660 (all parts).

Electrically propelled mopeds and motorcycles - Test specifications and safety requirements for lithium-ion battery systems

ISO 18246:2015 电力驱动的助力车和摩托车. 连接外部电源进行导电的安全要求

Electrically propelled mopeds and motorcycles - Safety requirements for conductive connection to an external electric power supply

QC/T 680-2014 摩托车和轻便摩托车用电压调节器技术条件

本标准规定了摩托车和轻便摩托车电压调节器的要求、试验方法、检验规则和标志、包装及储存。本标准适用于摩托车和轻便摩托车(以下简称摩托车)电压调节器(以下简称调节器)。

Specifications of voltage regulators for motorcycles and mopeds

SAE J1167-2014 摩托车停车灯开关

This SAE Recommended Practice establishes test procedures and performance requirements for stop lamp switches intended for use in an AC or a DC circuit on motorcycles. In service use may impose specific conditions on the switch which can affect its functional life. Those conditions should be replicated, as necessary, during the testing described in this document to ensure the adequate functioning of the device.

Motorcycle Stop Lamp Switch

SAE J1306-2012 摩托车辅助前照灯

This engineering design specification provides parameters and general requirements for auxiliary front lamps to be used on motorcycles.

Motorcycle Auxiliary Front Lamps

SAE J1577-2012 可换的摩托车前照灯泡

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability of technical requirements. Newer technology may exist. This SAE Recommended Practice provides performance parameters and dimensional specifications for available light sources (replaceable bulbs) which are appropriate for motorcycle headlamps.

Replaceable Motorcycle Headlamp Bulbs

SAE J1192-2010 摩托车用音响警告装置性能

The requirements of this document apply to all classes of motorcycles as defined in SAE J213. This document specifies performance and longevity requirements for motorcycle AWD?s with the goal of enhancing vehicle safety.

Performance of Audible Warning Devices for Motorcycles

SAE J1306-2010 摩托车辅助前照灯

This engineering design specification provides parameters and general requirements for auxiliary front lamps to be used on motorcycles.

Motorcycle Auxiliary Front Lamps

BS ISO 28981:2009 轻便摩托车.底盘测功机上设置运行阻力的方法

Mopeds - Methods for setting the running resistance on a chassis dynamometer

SAE J2577-2008 重型电灯电气连接器标准

This SAE Standard encompasses connectors that form the electrical interface(s) between the heavy duty lighting device(s) and the truck and truck/trailer wiring harness system. This document provides design and performance requirements based upon the mechanical, electrical and environmental conditions and covers applications of connectors for direct current electrical systems of 24 V nominal or less in heavy-duty signaling and marking devices. This standard excludes forward lighting devices (i.e. fog lamps) but includes the following list of lamps: Stop Lamps; Back Up Lamps; Tail Lamps; Side-Turn Signal Lamps; Turn Signal/Hazard Warning Lamps; Work Lamps; Side Marker Lamps; License Lamps; Clearance Lamps; Chassis Component Status (ABS) Lamps; Identification Lamps.

Heavy Duty Lamp Electrical Connector Standard

SAE J1167-2008 摩托车刹车灯开关

This SAE Recommended Practice establishes test procedures and performance requirements for stop lamp switches intended for use in an AC or a DC circuit on motorcycles. In service use may impose specific conditions on the switch which can affect its functional life. Those conditions should be replicated, as necessary, during the testing described in this document to ensure the adequate functioning of the device.

Motorcycle Stop Lamp Switch

SAE J2560-2007 摩托车前照明卤素灯泡性能要求

This SAE Recommended Practive is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document establishes performance requirements, material requirements, design requirements, and design guidelines for forward lighting halogen replaceable bulbs.

Forward Lighting Halogen Bulb Performance Requirements for Motor Vehicles

BS ISO 11460:2007 两轮摩托车.照明和光信号装置的位置控制

This International Standard specifies the requirements for the positioning of lighting and light-signalling devices when fitted to a two-wheeled motorcycle as defined in ISO 3833. It does not specify the installation of any of these devices.

Two-wheeled motorcycles - Positioning of lighting and light-signalling devices