共找到 253 条与 船舶工艺 相关的标准,共 17 页
本文件规定了船舶采用气囊下水时的通用要求,包括例如气囊、滑道、绞车、船舶下水程序和安全措施等船舶与设施的要求。 本文件适用于满足4.1要求并采用气囊方式下水的船舶。
Ships and marine technology—Methodology for ship launching utilizing air bag
本标准规定了船舶总段制造结构.策装`.涂装的完整性要求及状态确认。本标准适用于散货船油船、集装箱船的总段(上层建筑除外?制造完整性施工和状态确认,其他类型船舶可参照执行。
Integrity requirements of section fabrication for ship
本标准规定了船舶上层建筑制造结构.船装.涂装的完整性要求及状态确认。本标准适用于散货船.油船.集装箱船的上层建筑总段制造完整性施工和评价,其他类型船舶可参照执行。N
Integrity requirements of superstructure fabrication for ship
本标准规定了船舶钢焊颖超声相控阵检测(以下简称相控阵超声检测)的人员.仪器和设备.试块和耦合剂.检测技术等级.检测前技术要求、检测`检测数据分析及缺陷确定.检测工艺验证及系统复核、检测报告等要求。本标准适用于船舶钢焊颖相控阵超声检测。
Testing method of phased array technology for ship steel weld
本标准规定了船舶分段制造结构.策装`.涂装的完整性要求及状态确认。本标准适用于散货船.油船、集装箱船的分段制造完整性施工和状态确认,其他类型船舶可参照执行。
Integrity requirements of block fabrication for ship
Jack-up jacking system installation requirement
Spudcan penetration technology of self-elevating drilling unit
Technical requirement of closing condition for ship
Ships and marine technology—Protective coatings and inspection method —Part 1: Dedicated sea water ballast tanks
Ships and marine technology—Protective coatings and inspection method—Part 3: Cargo oil tanks of crude oil tankers
Ships and marine technology—Protective coatings and inspection method—Part 2: Void spaces of bulk carriers and oil tankers
本标准规定了船舶电弧焊烟尘排放率测定的一般要求、试验程序、测定结果计算及试验报告。 本标准适用于实验室环境下焊条电弧焊、气体保护焊焊接烟尘排放率及烟尘排放量的测定。
Determination of fume emission rate during arc welding of shipbuilding
China shipbuilding quality standard
本标准规定了海上浮式生产储存设备(FPS)的涂层保护和阴极保护要求。 本标准适用于海上浮式生产储存设备(FPS)腐蚀防护的设计、施工和验收。
Requirement of corrosion protection for floating production and storage units offshore
本标准规定了S型铺管作业线设备(简称铺管设备)的安装条件、安装前准备和设备安装。 本标准适用于S型铺管作业线设备的船上安装。
General installation requirements of S-lay system equipments for ships
本标准规定了大型游艇可视表面涂层外观的术语和定义、一般要求、光泽、颜色和其他表面缺陷等参数及其测量方法。 本标准适用于大型游艇,即用于运动、休闲和商业营运的,L(按EN ISO 8666的定义)不小于24 m的游艇。
Ships and marine technology.Large yachts.Measurement and assessment of the visual appearance of coatings
本标准规定了涂装前钢材表面经磨料喷、抛射清理后产生的表面粗糙度的视觉或触觉评定方法(比较样块法)和评定等级。 本标准适用于以金属或非金属磨料喷、抛射清理后的钢材及其他材料表面粗糙度的评定,也适用于其他防护处理前对钢材表面粗糙度要求的评定。 本标准适用于磨料喷、抛射清理后表面的除锈等级高于GB8923《涂装前钢材表面锈蚀等级和除锈等级》中Sa21/2级的钢材。对低于其级别的钢材可参照使用。 注:磨料包括丸状磨料和棱角状磨料。
The assessment of profile grades of steel surface before application of paint and related products.Comparator
Shafting flange connection bolt reaming and assembly quality requirements
Diese Norm gilt für Masthalterungen von losnehmbaren Masten mit eingebautem Mastfuß für die Lichterführung auf Schubleichtern. Sie legt Konstruktion, Maße, Ausführung, Anordnung und Befestigung fest.
Ships and marine technology - Inland navigation vessels - Mounting attachments for demountable signal masts for push-tows
本标准规定了钢质船舶涂装膜厚的膜厚分布、湿膜厚度控制、干膜厚度检测、膜厚检测数据记录、膜厚数据整理及膜厚交验等要求。 本标准适用于新建钢质船舶和钢质海洋结构物的涂装膜厚检测,其他钢结构物的涂装膜厚检测也可参照使用。
Inspection requirement of coating film thickness for ship
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号