V08 标志、包装、运输、贮存 标准查询与下载

GB/T 16992-1997 飞机维护及其安全警告标志

本标准规定了飞机上使用的维护及其安全警告标志（不包括单纯的文字标志），适用于各种类型的民用飞机。由于飞机维护点的尺寸和分布不同，采用本标准时，可以灵活执行本标准的要求。 本标准规定的标志以国际通用和易于识别为原则，为飞机地面作业提供方便，并为保障维护安全提出警告。

Aircraft--Identication of servicing, maintenance, ground handling and safety/hazard points

JIS W 8301:2016 航空用地面信号灯和色标

Aeronautical ground light and surface marking colours

SAE AIR5645A-2014 JAUS 传输注意事项

This SAE Aerospace Information Report (AIR) discusses characteristics of data communications for the Joint Architecture for Unmanned Systems (JAUS). This document provides guidance on the aspects of transport media, unmanned systems and the characteristics of JAUS itself that are relevant to the definition of a JAUS transport specification.

JAUS Transport Considerations

CFR 14-235.3-2014 航空和航天. 第235部分:航空公司涉及动物的航空运输事件报告. 第235.3节:航空公司涉及动物的航空运输事件的报告.

(a) Each covered carrier shall, within 15 days after the end of the month to which the information applies, submit to the United States Department of Transportation’s Aviation Consumer Protection Division a report on any incidents involving the loss, injury, or death of an animal during air transport provided by the air carrier, including incidents on flights by that carrier that are operated with aircraft having 60 or fewer seats.

Aeronautics and space. Part235:Reports by air carriers on incidents involving animals during air transport. Section235.3:Reports by air carriers on incidents involving animals during air transport.

SAE AS83461/2A-2014 O型圈MS83461型预制直螺纹管接头包装件

Scope is unavailable.

O-RING M83461 STRAIGHT THREAD TUBE FITTING BOSS

HB 8396-2013 民用飞机内外部应急标识

Emergency signs inside and outside of civil aircraft

DIN EN 4817:2012 航空航天系列.航空器用无源超高频无线射频识别(UHF RFID)标签.德文和英文版本EN 4817-2012

Aerospace series - Passive UHF RFID tags intended for aircraft use; German and English version EN 4817:2012

DIN EN 4818:2012 航空航天系列.航空器用高频射频识别(HF RFID)标签.德文和英文版本EN 4818-2012

Aerospace series - Passive HF RFID tags intended for aircraft use; German and English version EN 4818:2012

DIN EN 4819:2012 航空航天系列.航空器用接触式记忆钮(CMB)标签.德文和英文版本EN 4819-2012

Aerospace series - Contact Memory Button (CMB) tags intended for aircraft use; German and English version EN 4819:2012

SAE AS3084A-2012 预成型包装.AMS 7280.密封

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist.

Packing, Preformed - AMS 7280 - Seal

BS EN 4818:2012 航空航天系列.飞机用无源高频无线射频识别(HF RFID)标签

Aerospace series. Passive HF RFID tags intended for aircraft use

BS EN 4819:2012 航空航天系列.航空器用接触式记忆口塞(CMB)标签

Aerospace series. Contact Memory Button (CMB) tags intended for aircraft use

BS EN 4817:2012 航空航天系列.飞机用无源超高频无线射频识别(UHF RFID)标签

Aerospace series. Passive UHF RFID tags intended for aircraft use

ASTM D4306-12 受痕量杂质影响的试验用航空燃料采样容器标准规程

General descriptions for the manual sampling of petroleum products are given in Practice D4057. However, a number of aviation fuel properties are established or affected by trace levels of polar or other compounds. Measurement significance therefore requires that the sample containers not add or adsorb any materials. This practice presents types and preparations of sampling containers found satisfactory for the determination of water separation, copper corrosion, electrical conductivity, thermal stability, lubricity, and trace metal content. An approval procedure for new containers is also given. Two properties, particulate contamination and free water content, involve materials easily removed by any sampling container. These properties should be determined by placing the sample directly into the measuring apparatus and not using containers to transport the sample to the measuring equipment. Recommendations in this practice provide guidance for immediate use and for storage of samples. Immediate use involves sample storage for periods less than 24 h.1.1 This practice covers the types of and preparation of containers found most suitable for the handling of aviation fuel samples for the determination of critical properties affected by trace contamination. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 5.1, 5.2, 5.3, 5.4, and 5.6.

Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination

HB 20047-2011 航空工业外贸出口产品运输包装技术要求

本标准规定了航空工业外贸出口产品运输包装（以下简称运输包装)的技术要求、检验要求、运输包装件交货和验收及回收利用等要求。 本标准适用于航空工业外贸出口产品及为航空工业外贸出口配套的设备、成件、原材料及修理物品的运输包装。非航空工业生产的外贸出口产品相关要求可参照执行。

Technical requirements for shipping packages of export products of the aviation industry

SAE AMS2813G-2011 焊条装箱的包装和标识的标准方法

This specification covers spooling and packaging of bare welding wire to ensure cleanliness but with minimum environmental protection, spool sizes and weights of spooled wire, and package weights of cut lengths.

Packaging and Marking of Packages of Welding Wire Standard Method

KS W ISO 1749:2009 航空器.弹性密封圈.包装和识别

이 표준은 항공기의 탄성중합체 밀봉 링을 포장할 때 필요한 포장 및 식별에 대한 요구 사항

Aircraft-Elastomeric sealing rings-Packaging and identification

SAE AIR5558-2009 航天电线制作中的紫外线(UV)激光打标性能

The purpose of this report is to provide information on the results of ultra violet (UV) laser marking and mark contrast measurement of a wide range of aerospace wire and cable constructions, the specifications for most of which do not state specific requirements for laser markability. The contents of this document are for information and guidance only. It is not intended that it be used as the basis for marking process specifications or standards, which are covered by AS5649 Wire and Cable Marking Process, UV Laser.

Ultraviolet (UV) Laser Marking Performance of Aerospace Wire Constructions

SAE AMS2817F-2008 预成型包装件的包装和识别

This specification covers procedures which will provide protection of preformed packings, primarily "O" rings of elastomeric materials, from contamination by foreign materials prior to installation and ensure positive identification by part number of each piece until it is installed.

Packaging and Identification, Preformed Packings

WJ 2700-2008 战术导弹战斗部运输要求及试验方法

Transportation requirements and test methods for tactical missile warheads