共找到 102 条与 航天用起爆点火装置 相关的标准,共 7 页
This European Standard specifies the required characteristics and tests applicable to male electrical contacts 078, type A, crimp, class S, used in elements of connection according to EN 3155-002. It shall be used together with EN 3155-001. The associated female contacts are defined in EN 3155-079.
Aerospace series - Electrical contacts used in elements of connection - Part 078: Contacts size 22 for EN 2997, electrical, male, type A, crimp, class S - Product standard
This European Standard specifies the required characteristics, tests and tooling applicable to female electrical contacts 071, type A, crimp, class S used in elements of connection according to EN 3155-002. It shall be used together with EN 3155-001. The associated male contacts are defined in EN 3155-008 and EN 3155-070.
Aerospace series - Electrical contacts used in elements of connection - Part 071: Contacts@ electrical@ female@ type A@ crimp@ class S - Product standard
This European Standard specifies the required characteristics and tests applicable to male electrical contacts 080, type A, crimp, class T, used in elements of connection according to EN 3155-002. It shall be used together with EN 3155-001. The associated female contacts are defined in EN 3155-081.
Aerospace series - Electrical contacts used in elements of connection - Part 080: Contacts size 22 for EN 2997@ electrical@ male@ type A@ crimp@ class T - Product standard
This European Standard specifies the required characteristics, tests and tooling applicable to male electrical contacts 070, type A, crimp, class S, used in elements of connection according to EN 3155-002. It shall be used together with EN 3155-001. The associated female contacts are defined in EN 3155-003, EN 3155-009 and EN 3155-071.
Aerospace series - Electrical contacts used in elements of connection - Part 070: Contacts, electrical, male, type A, crimp, class S - Product standard
This European Standard specifies the required characteristics and tests applicable to female electrical contacts 081, type A, crimp, class T, used in elements of connection according to EN 3155-002. It shall be used together with EN 3155-001. The associated male contacts are defined in EN 3155-080.
Aerospace series - Electrical contacts used in elements of connection - Part 081: Contacts size 22 for EN 2997@ electrical@ female@ type A@ crimp@ class T - Product standard
This interface standard applies to fuzes used airborne weapons that use a 3-in fuze well. It defines: Physical envelope of the fuze well at the interface with the fuze; Load bearing surfaces of the fuze well; Physical envelope of the fuze and its connector; Mechanical features (e.g. clocking feature); Connector type, size, location and orientation; Retaining ring and its mechanical features (e.g. thread, tool interface); Physical envelope of the retaining ring at the interface with the fuze; Physical space available for installation tools; Torque that the installation tool shall be capable of providing. This standard does not address: Materials used or their properties; Protective finish; Physical environment of the weapon; Explosive interface or features (e.g. insensitive munitions (IM) mitigation); Charging tube; Torque on the retaining ring or loads on the load bearing surfaces. Each fuze and weapon combination should be evaluated to ensure that the weapon system will satisfy all safety, reliability, and performance requirements throughout its lifecycle.
Fuze Well Mechanical Interface
Technical Requirements for Acceptance of Surface-to-Surface Missile Bullet Fuze
Specification for auxiliary ignition ammunition for aircraft guns
General specification for gunpowder starters
Installation test requirements for tactical missile warhead and fuze
本规范规定了战术导弹触发引信(以下简称引信)的要求、质量保证规定和交货准备。 本规范适用于引信的设计、制造和验收。其它种类的触发引信可参照执行。
General specification for the contact fuze of tactical missiles
Requirements for destruction of XJ-2 series scrapped electromechanical fuzes
MIL-D-46634B dated 30 March 1990, and its Amendment 1 dated 12 June 1995, were originally inadvertantly issued as internal documents only. MIL-D-46634B and its Amendment 1 comprise the current document and has been in use in contracts since 12 June 1995.
DELAY ELEMENT, CARTRIDGE, M5 ASSEMBLY
MIL-D-46606B, dated 23 April 1991, and its Amendment 1 dated 31 May 1995, are hereby reinstated and may be used for acquisition.
DELAY ELEMENT, CARTRIDGE, M8 ASSEMBLY
This amendment forms a part of MIL-D-60568B, dated 15 January 1992, and is approved for use by all departments and agencies of the Department of Defense.
DELAY ELEMENT, CARTRIDGE, M13 ASSEMBLY
This specification covers the requirements for the manufacture and acceptance of the JAU-59/A Cartridge Actuated Initiator, referred to herein as the initiator.
INITIATOR, CARTRIDGE ACTUATED, JAU-59/A (MT06)
MIL-D-60842, including Amendment 1, dated 16 January 1987, is inactive for new design and is no longer used, except for replacement purposes.
DELAY ELEMENT, CARTRIDGE, XM17 ASSEMBLY
MIL-C-81730A, dated 19 April 1973, is inactive for new design and is no longer used, except for replacement purposes.
CARTRIDGE, DELAY, MARK 136 MOD 0
MIL-D-50727B, including Amendment 1, dated 16 October 1986, is inactive for new design and is no longer used, except for replacement purposes.
DELAY ELEMENT ASSEMBLIES
MIL-D-60571B, including Amendment 1, dated 8 December 1986, is inactive for new design and is no longer used, except for replacement purposes.
DELAY ELEMENT, CARTRIDGE, XM44 ASSEMBLY
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号