共找到 68 条与 相关的标准,共 5 页
Rubber and plastics hoses and hose assemblies - Ratios of proof and burst pressure to maximum working pressure (ISO 7751:2016); German version EN ISO 7751:2016
Rubber and plastics hoses and hose assemblies - Guidelines for selection, storage, use and maintenance (ISO 8331:2016); German version EN ISO 8331:2016
This document specifies methods for the determination of the adhesion between lining and reinforcement, between cover and reinforcement, between reinforcement layers, between cover and outer lamination (thin layer of material outside the cover for protection) and between lining and inner lamination (thin layer of material inside the lining to reduce permeation of fluid into the lining). It covers all bore sizes and the following types of hose construction: — woven textile fabric; — braided textile fabric; — knitted textile fabric; — circular-woven textile fabric; — textile spiral; — textile cord; — wire braid; — wire spiral; — hoses containing a supporting helix. Adequate adhesion between the various components of a hose is essential if it is to perform satisfactorily in service.
Rubber and plastics hoses - Determination of adhesion between components
This document specifies ratios of proof pressure and minimum burst pressure to maximum working pressure for various categories of hose service.
Rubber and plastics hoses and hose assemblies - Ratios of proof and burst pressure to maximum working pressure
Rubber and plastics hoses and hose assemblies. Determination of resistance to vacuum
Rubber and plastics hoses and hose assemblies - Determination of resistance to vacuum
Polyethylene (PE) coiling pipes and hoses for use in irrigation systems - Hoses of nonrigid material with woven fabric inner layer - Part 3: Dimensions and technical delivery conditions
Rubber and plastics hoses and tubing. Determination of transmission of liquids through hose and tubing walls
This International Standard specifies two methods for the determination of transmission of liquids through hose and tubing walls. Both methods are applicable to rubber and plastics hose and tubing, and comprise: — method A, for all hose and tubing sizes and constructions: a practical comparative test, simulating working conditions; — method B, for hose and tubing up to 16 mm inside diameter.
Rubber and plastics hoses and tubing - Determination of transmission of liquids through hose and tubing walls
Rubber and plastics hoses and hose assemblies. Vocabulary
Diese Internationale Norm legt Anforderungen fest fur drei Arten von thermoplastischen Schlauchen verstarkt mit einer thermoplastischen Wendel zum Ansaugen und Fordern von Wasser, verdunnten wassrigen Chemikalienlosungen und abrasiven Feststoffen und Schlammen fur den Gebrauch in einem Umgebungstemperaturbereich von -10 °C bis 55 °C. Diese drei Arten von Schlauchen sind anwendbar fur leichte, mittlere und schwere Beanspruchungen Die in dieser Internationalen Norm enthaltenen Schlaucharten sind nicht bestimmt fur die Verwendung mit entflammbaren und brennbaren Materialien, sowie mit aromatischen Losungsmitteln. ANMERKUNG Schlauche mit ahnlichem Aufbau zum Ansaugen und Fordern fur die Feuerbekampfung sind in ISO 14557 beschrieben.
Plastics hoses - Helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of aqueous materials - Specification (ISO 3994:2014)
Rubber and plastics hoses and tubing. Measurement of flexibility and stiffness. Bending tests at sub-ambient temperatures
Rubber and plastics hoses and tubing. Measurement of flexibility and stiffness. Bending tests at ambient temperature
Rubber and plastics hoses. Methods of exposure to laboratory light sources. Determination of changes in colour, appearance and other physical properties
Rubber and plastics hoses and hose assemblies - Ratios of proof and burst pressure to maximum working pressure - Amendment 1: Replacement of "design working pressure" by "maximum working pressure" throughout text
Rubber and plastics hoses and hose assemblies - Ratios of proof and burst pressure to maximum working pressure - Amendment 1: Replacement of "design working pressure" by "maximum working pressure" throughout text
Rubber and plastics hoses -- Part 7: Assessment of ozone resistance under static conditions
Rubber and plastics hoses and tubing - Determination of transmission of liquids through hose and tubing walls (ISO 8308:2006); German version EN ISO 8308:2008; Corrigendum to DIN EN ISO 8308:2008-06
Rubber and plastics hoses and tubing - Textile reinforced types - Sub-ambient temperature crush test
호스의 여러 구성요소 간의 적절한 접착성은 사용시 만족할 만한 성능을 나타내는 데 필수적이
Rubber and plastics hoses-Determination of adhesion between components
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号