13.220.40;75.080 标准查询与下载
共找到 14 条与 相关的标准，共 1 页
This document specifies a method by which the fire hazards of pressurised sprays of fire-resistant fluids can be compared. Two sizes of propane flame are used to ignite and stabilise combustion of an air-atomised release of fluid. Measurements related to the rate of heat release, length of flame and density of smoke give quantitative information on the fire behaviour of the fluid.
Petroleum and related products - Determination of spray ignition characteristics of fire-resistant fluids - Part 2: Spray test - Stabilised flame heat release method
- ICS
- 13.220.40;75.080
- CCS
- E30
- 发布
- 2018-04-01
- 实施
Petroleum products. Methods for determination of flash point in Pensky-Martens closed cup
- ICS
- 13.220.40;75.080
- CCS
- 发布
- 2013
- 实施
- 2015-01-01
Petroleum and related products - Determination of spray ignition characteristics of fire-resistant fluids - Part 2: Spray test - Stabilized flame heat release method
- ICS
- 13.220.40;75.080
- CCS
- E30
- 发布
- 2012-12
- 实施
Petroleum and related products - Determination of the flammability characteristics of fluids in contact with hot surfaces - Manifold ignition test (ISO 20823:2003)
- ICS
- 13.220.40;75.080
- CCS
- 发布
- 2004-08-30
- 实施
- 2004-08-30
Petroleum and related products - Determination of the flammability characteristics of fluids in contact with hot surfaces - Manifold ignition test (ISO 20823:2003); German version EN ISO 20823:2003
- ICS
- 13.220.40;75.080
- CCS
- E30
- 发布
- 2003-10
- 实施
ISO 20823:2003 specifies a test method to determine the relative flammability of fluids when contacted with a hot metal surface at a fixed temperature, but it is also possible to gauge fluid ignition temperatures by adjustment of the manifold temperature. It is primarily used is to assess the resistance to ignition of fire-resistant hydraulic fluids which are, by definition, difficult to ignite. It may be used with other types of more flammable fluids at lower surface temperatures, but this could significantly increase the hazards of this procedure.
Petroleum and related products - Determination of the flammability characteristics of fluids in contact with hot surfaces - Manifold ignition test
- ICS
- 13.220.40;75.080
- CCS
- E30
- 发布
- 2003-08-13
- 实施
- 2003-08-13
Petroleum and related products - Determination of the flammability characteristics of fluids in contact with hot surfaces - Manifold ignition test ISO 20823:2003
- ICS
- 13.220.40;75.080
- CCS
- 发布
- 2003-08-01
- 实施
Methods of test for petroleum and its products - Determination of flash point - Pensky-Martens closed cup method
- ICS
- 13.220.40;75.080
- CCS
- E30
- 发布
- 2002-12-10
- 实施
- 2002-12-10
This International Standard describes two procedures, A and B, using the Pensky-Martens closed cup tester, for determining the flash point of combustible liquids, liquids with suspended solids, liquids that tend to form a surface film under the test conditions and other liquids. It is applicable for liquids with a flash point above 40 ℃. NOTE 1 Although technically kerosines with a flash point above 40 ℃ may be tested using this International Standard, it is standard practice to test kerosines according to ISO 13736. Similarly, unused lubricating oils are normally tested according to ISO 2592 Procedure A is used for the determination of the flash point of paints and varnishes that do not form a surface film, unused lubricating oils and other petroleum products not covered by Procedure B. Procedure B is used for the determination of the flash point of residual fuel oils, cutback bitumens, used lubricating oils, liquids that tend to form a surface film, liquids with suspensions of solids and highly viscous materials such as polymeric solutions and adhesives. NOTE 2 For the comparison of the flash points of used and unused lubricating oils, such as in a lubricant monitoring scheme, used lubricating oils may be tested using Procedure A. However, the precision data for these materials is only valid for Procedure B. This International Standard is not applicable to water-borne paints or liquids contaminated by traces of highly volatile materials. NOTE 3 Water-borne paints may be tested using ISO 3679 Liquids contaminated by traces of highly volatile materials may be tested using ISO 1523 or ISO 3679. NOTE 4 Precision data is only valid for the flash point ranges given in clause 13.
Determination of flash point - Pensky-Martens closed cup method
- ICS
- 13.220.40;75.080
- CCS
- E30
- 发布
- 2002-11
- 实施
The document specifies a method for the determination of spray ignition characteristics of fire-resistant fluids.
Petroleum and related products - Determination of spray ignition characteristics of fire-resistant fluids - Part 1: Spray flame persistance; Hollow-cone nozzle method (ISO 15029-1:1999); German version EN ISO 15029-1:1999
- ICS
- 13.220.40;75.080
- CCS
- E30
- 发布
- 2002-10
- 实施
This part of ISO 15029 specifies a hollow-cone nozzle method for the assessment of the persistence of a flame applied to various points within a pressurized spray of fire-resistant fluid. This part of ISO 15029 is one of two basic measures of fire-resistance, and may be called up in regulations governing their use under the 7th edition of the Luxembourg Report. note:1) Safety and Health Commission for the Mining and other Extractive Industries, Doc. No. 4746/10/91 EN (for English version, FR for French version), April 1994, Requirements and tests applicable to fire-resistant hydraulic fluids used for power transmissions and control (hydrostatic and hydrokinetic), available from the Commission of the European Communities, Directorate-General V, Unit V.F.4 "Extractive, Iron and Steel Industries", Batiment Jean Monnet, C4/65, L-2920 Luxembourg.
Petroleum and related products - Determination of spray ignition characteristics of fire-resistant fluids - Spray flame persistence - Hollow-cone nozzle method
- ICS
- 13.220.40;75.080
- CCS
- E30
- 发布
- 2000-08-15
- 实施
- 2000-08-15
This part of the standard specifies a hollow-cone nozzle method for the assessment of the persistance of a flame applied to various points within a pressurized spray of fire-resistent fluid.
Petroleum and related products - Determination of spray ignition characteristics of fire-resistant fluids - Part 1: Spray flame persistence - Hollow-cone nozzle method
- ICS
- 13.220.40;75.080
- CCS
- 发布
- 2000-05-05
- 实施
- 2000-02-21
This part of ISO 15029 specifies a hollow-cone nozzle method for the assessment of the persistence of a flame applied to various points within a pressurized spray of fire-resistant fluid. This part of ISO 15029 is one of two basic measures of fire-resistance, and may be called up in regulations governing their use under the 7th edition of the Luxembourg Report. note:1) Safety and Health Commission for the Mining and other Extractive Industries, Doc. No. 4746/10/91 EN (for English version, FR for French version), April 1994, Requirements and tests applicable to fire-resistant hydraulic fluids used for power transmissions and control (hydrostatic and hydrokinetic), available from the Commission of the European Communities, Directorate-General V, Unit V.F.4 "Extractive, Iron and Steel Industries", Batiment Jean Monnet, C4/65, L-2920 Luxembourg.
Petroleum and related products - Determination of spray ignition characteristics of fire-resistant fluids - Part 1: Spray flame persistence - Hollow-cone nozzle method
- ICS
- 13.220.40;75.080
- CCS
- E30
- 发布
- 1999-12
- 实施
Petroleum and Related Products - Determination of Spray Ignition Characteristics of Fire-Resistant Fluids - Part 1: Spray Flame Persistence - Hollow-Cone Nozzle Method ISO 15029-1:1999
- ICS
- 13.220.40;75.080
- CCS
- 发布
- 1999
- 实施
