25.160.30;33.100.01 标准查询与下载
共找到 14 条与 相关的标准，共 1 页
Resistance welding equipment - Part 2: Electromagnetic compatibility (EMC) requirements (IEC 62135-2:2015); German version EN 62135-2:2015
- ICS
- 25.160.30;33.100.01
- CCS
- L06
- 发布
- 2015-11
- 实施
This part of IEC 62135 is applicable to equipment for resistance welding and allied processes which are connected to mains supplies with rated voltages up to 1 000 V a.c. r.m.s. This standard does not define safety requirements. Resistance welding equipment type tested in accordance with@ and which has met the requirements of@ this standard@ is deemed to be in compliance for all applications. The frequency range covered is from 0 Hz to 400 GHz. This product EMC standard for resistance welding equipment takes precedence over all aspects of the generic standards and no additional EMC tests are required or necessary. NOTE 1 Typical allied processes are resistance hard and soft soldering or resistance heating achieved by means comparable to resistance welding equipment. NOTE 2 Limit values are specified for only part of the frequency range. Resistance welding equipment are classified as class A and class B equipment. This part of IEC 62135 specifies a) test methods to be used in conjunction with CISPR 11 to determine radiofrequency (RF) emission; b) relevant standards and test methods for harmonic current emission@ voltage fluctuation and flicker. NOTE 3 The limits in this standard cannot@ however@ provide full protection against interference to radio and television reception when the resistance welding equipment is used closer than 30 m to the receiving antenna(e). NOTE 4 In special cases@ when highly susceptible apparatus is being used in close proximity@ additional mitigation measures are sometimes employed to further reduce the electromagnetic emissions. This part of IEC 62135 also defines immunity requirements and test methods for continuous and transient@ conducted and radiated disturbances including electrostatic discharges. NOTE 5 These requirements do not@ however@ cover extreme cases which are extremely rare.
Resistance welding equipment - Part 2: Electromagnetic compatibility (EMC) requirements
- ICS
- 25.160.30;33.100.01
- CCS
- J64
- 发布
- 2015-02
- 实施
- 2015-02-26
Arc welding equipment - Part 10: Electromagnetic compatibility (EMC) requirements
- ICS
- 25.160.30;33.100.01
- CCS
- J64
- 发布
- 2014-02
- 实施
- 2014-02-08
Electromagnetic compatibility of technical equipment. Resistance welding equipment. Part 2. Requirements and test methods
- ICS
- 25.160.30;33.100.01
- CCS
- 发布
- 2012
- 实施
- 2013-01-01
Electromagnetic compatibility of technical equipment. Arc welding equipment. Part 10. Requirements and test methods
- ICS
- 25.160.30;33.100.01
- CCS
- 发布
- 2012
- 实施
- 2013-01-01
Arc welding equipment - Part 10: Electromagnetic compatibility (EMC) requirements; Corrigendum 1
- ICS
- 25.160.30;33.100.01
- CCS
- J64
- 发布
- 2011-06-01
- 实施
- 2014-02-08
This part of IEC 62135 is applicable to equipment for resistance welding and allied processes which are connected to mains supplies with rated voltages up to 1 000 V a.c. r.m.s. This standard does not define safety requirements. Resistance welding equipment type tested in accordance with, and which has met the requirements of, this standard, shall be deemed to be in compliance for all applications. The frequency range covered is from 0 Hz to 400 GHz. This product EMC standard for resistance welding equipment takes precedence over all aspects of the generic standards and no additional EMC tests are required or necessary. NOTE 1 Typical allied processes are resistance hard and soft soldering or resistance heating achieved by means comparable to resistance welding equipment. NOTE 2 Limit values are specified for only part of the frequency range. Resistance welding equipment are classified as Class A and Class B equipment. This part of IEC 62135 specifies a) test methods to be used in conjunction with CISPR 11 to determine radiofrequency (r.f.) emission; b) relevant standards and test methods for harmonic current emission, voltage fluctuation and flicker. NOTE 3 The limits in this standard may not, however, provide full protection against interference to radio and television reception when the resistance welding equipment is used closer than 30 m to the receiving antenna(e). NOTE 4 In special cases, when highly susceptible apparatus is being used in close proximity, additional mitigation measures may have to be employed to further reduce the electromagnetic emissions. This part of IEC 62135 also defines immunity requirements and test methods for continuous and transient, conducted and radiated disturbances including electrostatic discharges. NOTE 5 These requirements do not, however, cover extreme cases which are extremely rare.
Resistance welding equipment — Part 2: Electromagnetic compatibility (EMC) requirements
- ICS
- 25.160.30;33.100.01
- CCS
- 发布
- 2008-07-31
- 实施
Resistance welding equipment. Electromagnetic compatibility (EMC) requirements
- ICS
- 25.160.30;33.100.01
- CCS
- J64
- 发布
- 2008-07-31
- 实施
- 2008-07-31
Resistance welding equipment - Part 2 : electromagnetic compatibility (EMC) requirements.
- ICS
- 25.160.30;33.100.01
- CCS
- J64
- 发布
- 2008-04-01
- 实施
- 2008-04-19
Electromagnetic compatibility (EMC) - Product standard for resistance welding equipment.
- ICS
- 25.160.30;33.100.01
- CCS
- L06
- 发布
- 2005-01-01
- 实施
- 2005-01-20
This standard is applicable to equipment for resistance welding and allied processes intended for use in industrial and light industrial environments which are connected to mains supplies with rated voltages up to 1 000 V a.c. rms. This standard does not define safety requirements. Resistance welding equipment type tested in accordance with, and which has met the requirements of this standard, shall be deemed to be in compliance for all applications. The frequency range covered is from 0 Hz to 400 GHz. This product EMC standard for resistance welding equipment takes precedence over all aspects of the generic standards and no additional EMC tests are required or necessary. NOTE 1 Typical allied processes are resistance hard and soft soldering or resistance heating achieved by means comparable to resistance welding equipment. NOTE 2 Limit values are specified for only part of the frequency range. Resistance welding equipment are classified as class A and class B equipment. 1 Emission The objective of this standard is to specify: a) test methods to be used in conjunction with EN 55011:1998 and its amendments A1:1999 and A2:2002 to determine electromagnetic emission; b) relevant standards for harmonic current emission, voltage fluctuations and flicker. NOTE 1 The limits in this standard may not, however, provide full protection against interference to radio and television reception when the resistance welding equipment is used closer than 30 m to the receiving antenha(e). NOTE 2 In special cases, when highly susceptible apparatus is being used in close proximity, additional mitigation measures may have to be employed to further reduce the electromagnetic emissions. 2 Immunity The objective of this standard is to define immunity requirements and test methods for continuous and transient, conducted and radiated disturbances including electrostatic discharges. NOTE These levels do not, however, cover extreme cases which are extremely rare.
Electromagnetic compatibilty (EMC) - Product standard for resistance welding equipment
- ICS
- 25.160.30;33.100.01
- CCS
- L06
- 发布
- 2004-12-01
- 实施
- 2004-12-01
Applicable to equipment for arc welding and allied processes, including power sources and ancillary equipment, for example wire feeders, liquid cooling systems and arc striking and stabilising devices. With regard to emissions, the objective of this stan
Arc welding equipment - Part 10: Electromagnetic compatibility (EMC) requirements
- ICS
- 25.160.30;33.100.01
- CCS
- J64
- 发布
- 2004-10
- 实施
This part of IEC 60974 is applicable to equipment for arc welding and allied processes, including power sources and ancillary equipment, for example wire feeders, liquid cooling systems and arc striking and stabilising devices. NOTE 1 Allied processes are, e.g., plasma cutting and arc stud welding. NOTE 2 This standard does not specify basic safety requirements for arc welding equipment such as protection against electric shock, unsafe operation, insulation co-ordination and related dielectric tests. Arc welding equipment type tested in accordance with, and which has met the requirements of, this standard is considered to be in compliance for all applications. 1 Emission The objective of this standard is to specify a) test methods to be used in conjunction with CISPR 11 and its amendments 1 and 2 to determine electromagnetic emissions; b) relevant standards for harmonic current emission, voltage fluctuations and flicker. 2 Immunity The objective of this standard is to define immunity requirements and test methods for continuous and transient, conducted and radiated disturbances including electrostatic discharges. NOTE 3 These requirements do not cover extreme cases, which may occur with an extremely low probability of occurrence in any location.
Arc welding equipment - Part 10: Electromagnetic compatibility (EMC) requirements
- ICS
- 25.160.30;33.100.01
- CCS
- J64
- 发布
- 2002-08
- 实施
- 2004-08-27
Настоящий стандарт распространяется на оборудование для дуговой сварки, предназначенное для использования в промышленных и бытовых усло
Electromagnetic compatibility of technical equipment. Arc welding equipment. Requirements and test methods
- ICS
- 25.160.30;33.100.01
- CCS
- 发布
- 1999
- 实施
- 2002-01-01
