43.020;43.180 标准查询与下载
共找到 15 条与 相关的标准，共 1 页
本标准规定了二组份汽油车排气分析仪和四组份汽油车排气分析仪（以下简称仪器）的检定技术要求和检定方法。 二组份汽油车分析仪为应用不分光红外线原理检测汽油车排气中的CO、HC成分。 四组份汽油车分析仪为应用不分光红外线原理检测汽油车排气中的CO、HC、CO成分,应用电化学原理检测汽油车排气中的O成分。 本标准适用于机动车安全检测用汽油车排气分析仪的检定。
Motor vehicle safety testing equipment Technical requirements of verification--Part 3: Technical requirements of verification for gasoline motor vehicle emission analyzer
- ICS
- 43.020;43.180
- CCS
- R82
- 发布
- 2001-04-29
- 实施
- 2001-12-01
本标准规定了滚筒式车速表试验台（以下简称车速台）的检定技术要求和检定方法。 本标准适用于机动车安全检测用车速台的检定。
Motor vehicle safety testing equipment Technical requirements of verification--Part 4: Technical requirements of verification for speedometer tester of roller type
- ICS
- 43.020;43.180
- CCS
- R82
- 发布
- 2001-04-29
- 实施
- 2001-12-01
本标准规定了滤纸式烟度计（以下简称烟度计）的检定技术要求和检定方法。 本标准适用于机动车安全检测用烟度计的检定。
Motor vehicle safety testing equipment Technical requirements of verification--Part 5: Technical requirements of verification for filter type smokemeter
- ICS
- 43.020;43.180
- CCS
- R82
- 发布
- 2001-04-29
- 实施
- 2001-12-01
本标准规定了对称光前照灯检测仪（以下简称大灯仪）的检定技术要求和检定方法。 本标准适用于机动车安全检测用大灯仪的检定。
Motor vehicle safety testing equipment Technical requirements of verification--Part 6: Technical requirements of verification for symmetrical beam headlamp tester
- ICS
- 43.020;43.180
- CCS
- R82
- 发布
- 2001-04-29
- 实施
- 2001-12-01
本标准规定了用于测量机动车各轴（轮）重力载荷的轴（轮）重仪的检定技术要求和检定方法。 本标准适用于机动车安全检测用轴（轮）重仪和制动轴（轮）重复合检验台中轴（轮）重部分的检定。
Motor vehicle safety testing equipment Technical requirements of verification--Part 7: Technical requirements of verification for Axle(Wheel) load scales
- ICS
- 43.020;43.180
- CCS
- R82
- 发布
- 2001-04-29
- 实施
- 2001-12-01
本标准规定了摩托车轮偏检测仪（以下简称轮偏仪）的检定技术要求和检定方法。 本标准适用于摩托车安全检测用轮偏仪的检定。
Motor vehicle safety testing equipment Technical requirements of verification--Paet 8: Technical requirements of verification of motorcycle wheel deviation tester
- ICS
- 43.020;43.180
- CCS
- R82
- 发布
- 2001-04-29
- 实施
- 2001-12-01
本标准规定了平板制动试验台的检定技术要求和检定方法。 本标准适用于机动车安全检测用平板制动试验台（以下简称制动台）及平板式制动－轮重复合试验台的制动部分的检定。
Motor vehicle safety testing equipment Technical requirements of verification--Part 9: Technical requirements of verification for platform brake tester
- ICS
- 43.020;43.180
- CCS
- R82
- 发布
- 2001-04-29
- 实施
- 2001-12-01
本标准规定了滚筒反力式制动试验台（以下简称制动台）的检定技术要求和检定方法。 本标准适用于机动车安全检测用滚筒反力式制动试验台的检定。
Motor vehicle safety testing equipment Technical requirements of verification--Part 2: Technical requirements of verification for opposite force roller brake tester
- ICS
- 43.020;43.180
- CCS
- R82
- 发布
- 2001-04-29
- 实施
- 2001-12-01
Procedure to construct injury risk curves for the evaluation of road user protection in crash tests
- ICS
- 43.020;43.180
- CCS
- T04
- 发布
- 2014-03
- 实施
This Technical Report specifies a method to calculate the level of correlation between two non-ambiguous signals. The focus of the methods described in this Technical Report is on the comparison of time-history signals or functional responses obtained in all kinds of tests of the passive safety of vehicles and the corresponding numerical simulations. It is validated with signals of various kinds of physical loads such as forces, moments, accelerations, velocities, and displacements. However, other applications might be possible too, but are not in the scope of this Technical Report.
Road vehicles.Objective rating metrics for dynamic systems
- ICS
- 43.020;43.180
- CCS
- T04;R16
- 发布
- 2013-07-15
- 实施
This International Standard specifies dynamic side impact test procedures with poles for evaluating the effects of the interaction between side airbags and occupants of road vehicles.
Road vehicles - Side impact test procedures for the evaluation of occupant interactions with side airbags by pole impact simulation
- ICS
- 43.020;43.180
- CCS
- Z32
- 发布
- 2013-06-15
- 实施
This International Standard specifies a general frontal test procedure for impact on fixed barrier or pole. There are several applicable test configurations, some with specific test procedures. This International Standard describes general testing requirements for conducting accurate and uniform frontal testing.
Road vehicles - Frontal fixed barrier or pole impact test procedure
- ICS
- 43.020;43.180
- CCS
- T04
- 发布
- 2013-06-15
- 实施
This part of ISO 15830 specifies requirements for electronic components of the WorldSID 50th percentile side-impact dummy, a standardized anthropomorphic dummy for side-impact testing of road vehicles. It is applicable to impact tests involving — passenger vehicles of category M1 and goods vehicles of category N1, — impacts to the side of the vehicle structure, — impact tests involving the use of an anthropometric dummy as a human surrogate for the purpose of evaluating compliance with vehicle safety standards.
Road vehicles.Design and performance specifications for the WorldSID 50th percentile male side-impact dummy.Part 3: Electronic subsystems
- ICS
- 43.020;43.180
- CCS
- T04
- 发布
- 2013-05-15
- 实施
This part of ISO 15830 specifies requirements for assembling and disassembling of the WorldSID 50th percentile side impact dummy, a standardized anthropomorphic dummy for side impact testing of road vehicles. It is applicable to impact tests involving — passenger vehicles of categories M1 and goods vehicles of categories N1, — impacts to the side of the vehicle structure, — impact tests involving the use of an anthropometric dummy as a human surrogate for the purpose of evaluating compliance with vehicle safety standards.
Road vehicles.Design and performance specifications for the WorldSID 50th percentile male side impact dummy.Part 4: User's manual
- ICS
- 43.020;43.180
- CCS
- T04
- 发布
- 2013-05-15
- 实施
This part of ISO 15830 specifies requirements for mechanical components, drawings and specifications,validation tests, and support equipment for the WorldSID 50th percentile side-impact dummy, a standardized anthropomorphic dummy for side-impact testing of road vehicles. It is applicable to impact tests involving — passenger vehicles of category M1 and goods vehicles of category N1, — impacts to the side of the vehicle structure, and — impact tests involving use of an anthropomorphic dummy as a human surrogate for the purpose of evaluating compliance with vehicle safety standards.
Road vehicles.Design and performance specifications for the WorldSID 50th percentile male side-impact dummy.Part 2: Mechanical subsystems
- ICS
- 43.020;43.180
- CCS
- T04
- 发布
- 2013-05-15
- 实施
