75.100;75.120 标准查询与下载

DIN EN ISO 6743-4:2015 润滑剂、工业用润滑油和相关产品(L类).分类.第4部分:H族(液压系统)(ISO 6743-4-2015);德文版本EN ISO 6743-4-2015

Lubricants, industrial oils and related products (class L) - Classification - Part 4: Family H (Hydraulic systems) (ISO 6743-4:2015); German version EN ISO 6743-4:2015

EN ISO 6743-4:2015 润滑剂,工业用油和有关产品(L类).分类.第4部分:H系列（液压系统）（ISO 6743-4:2015）

Dieser Teil von ISO 6743 beinhaltet die genaue Klassifikation von Flüssigkeiten der Familie H (Hydraulische Systeme), die zur Klasse L (Schmierstoffe, Industrieöle und verwandte Erzeugnisse) gehören. Der vorliegende Teil ist dafür vorgesehen, in Zusammenhang mit ISO 6743-99 gelesen zu werden. Bremsflüssigkeiten für Kraftfahrzeuge oder Hydraulikflüssigkeiten für Flugzeuge sind in diesem Klassifikationssystem nicht enthalten.

Lubricants@ industrial oils and related products (class L) - Classification - Part 4: Family H (Hydraulic systems)

KS M ISO 12922:2013 润滑油、工业油及有关产品(L级).H系列(液压系统).HFAE、HFAS、HFB、HFC、HFDR和HFDU类别规范

이 표준은 일반 산업 적용에서 유체 정역학과 유체 역학의 유압 시스템의 미사용 난연성 유압유 및저인화성 유압유의 최소 요구사항을 규정한다. 항공 우주 산업 또는 동력 발생 용도에서의 사용을목적으로 하지 않는다. 여기에는 다른 요구사항이 적용된다. 유해성이 적은 유체의 공급자와 최종 사용자를 위한 지침 및 이들 유체를 사용하는 유압 장비의 제조자에 대한 지침을 제공한다.유압 적용에 사용되는 다양한 형태의 유체를 분류하는 KS M ISO 6743-4에서 다루는 범주 중에서이 표준에서는 HFAE, HFAS, HFB, HFC, HFDR, HFDU만을 상세히 다룬다.KS B ISO 5598에서 정의한 바와 같이 HFAE, HFAS, HFB, HFC 및 HFDR은 난연성 유체이다. 대부분의 HFDU 유체는 연소 경향에 있어 광유보다 향상된 모습을 보이기는 하지만, 난연성 유체로 정의하기보다는 저인화성 유체로 생각하는 것이 보다 적절하다.

Lubricants, industrial oils and related products(class L) — Family H(Hydraulic systems) — Specifications for categories HFAE, HFAS, HFB, HFC, HFDR and HFDU

GOST ISO 13357-1-2013 石油制品. 润滑油过滤性的测定. 第1部分. 水中过滤油

Petroleum products. Determination of the filterability of lubricating oils. Part 1. Oils in the presence of water

DIN ISO 6743-99:2012 润滑剂, 工业用油及相关产品(L类). 分类. 第99部分: 总则(ISO 6743-99-2002)

Lubricants, industrial oils and related products (class L) - Classification - Part 99: General (ISO 6743-99:2002)

DIN CEN/TR 16227:2011 液化石油产品.生物润滑油.生物润滑油及生物基质润滑油的术语和特性描述推荐标准;德文版CEN/TR 16227-2011

Liquid petroleum products - Bio-lubricants - Recommendation for terminology and characterisation of bio-lubricants and bio-based lubricants; German version CEN/TR 16227:2011

PD CEN/TR 16227:2011 液体石油产品.生物基润滑油.生物基润滑油的术语和表征

This Technical Report gives information about bio-lubricants and recommendations for bio-lubricant (and bio-based lubricant) related terminology. These recommendations are based on a discussion of commonly used terms in this field. This Technical Report also briefly describes the current test methods in relation to the characterization of bio-lubricants. It presents recommendations for related standards in the field of biodegradability, product functionality, impact on greenhouse gas emissions and the amount of different renewable raw materials and/or different bio-based contents used during manufacturing of such bio-lubricants forming one product group. The criteria of the European Ecolabel for Lubricants ("EEL") include the terms discussed in this paper. NOTE 1 The European Lead Market Initiative ("LMI") defines the term "bio-based" as described in Table 1. It is important to mention that "bio-based" does not imply "biodegradable". In addition, "biodegradable" does not imply the use of "bio-based" material. NOTE 2 For the purposes of this European Technical Report, the term "% (m/m)" is used to represent the mass fraction.

Liquid petroleum products - Bio-lubricants - Recommendation for terminology and characterisation of bio-lubricants and bio-based lubricants

ASTM D7665-10(2014) 评估可生物降解传热流体的标准指南

4.1 The significance of each test method depends upon the system in use and the purpose of the test method as listed under Section 5. Use the most recent editions of ASTM test methods. 1.1 This guide2 covers general information, without specific limits, for selecting standard test methods for evaluating heat transfer fluids for quality and aging. These test methods are considered particularly useful in characterizing biodegradable water free heat transfer fluids in closed systems. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

Standard Guide for Evaluation of Biodegradable Heat Transfer Fluids

DIN ISO 13357-1:2009 石油产品.润滑油可过滤性的测定.第1部分:水中过滤油的规程

This part of ISO 13357 specifies a procedure for the evaluation of the filterability of lubricating oils, particularly those designed for hydraulic applications, in the presence of water. The procedure only applies to mineral-based oils, since fluids manufactured from other materials (e.g. fire-resistant fluids) may not be compatible with the specified testmembranes. The range of application has been evaluated with oils of viscosity up to ISO viscosity grade (VG) 100, as defined in ISO 3448. Within the range described, the filterability as defined is not dependent on the viscosity of the oil. The procedure is not suitable for some hydraulic oils on which specific properties have been conferred by the use of insoluble/partially soluble additives, or by particularly large molecular species. NOTE Filterability is a prime requirement for lubricating oils used in hydraulic systems because of the fine filters used in this application. This part of ISO 13357 defines a method for assessing the filterability of oils in the presence of contaminating water. It should be noted that some oils will exhibit poorer filterability characteristics in these conditions. ISO 13357-2 should be used to investigate the filterability of an oil which is to be used in applications where the presence of water in the oil is unlikely. An oil which has good filterability in the presence of contaminating water will not necessarily have equally good filterability in dry conditions. An oil having good filterability only when wet is unlikely to be generally acceptable.

Petroleum products - Determination of the filterability of lubricating oils - Part 1: Procedure for oils in the presence of water (ISO 13357-1:2002); English version of DIN ISO 13357-1:2009-04

DIN ISO 13357-1:2008 石油产品.润滑油过滤性的测定.第1部分:水中油的过滤程序

This part of ISO 13357 specifies a procedure for the evaluation of the filterability of lubricating oils, particularly those designed for hydraulic applications, in the presence of water. The procedure only applies to mineral-based oils, since fluids manufactured from other materials (e.g. fire-resistant fluids) may not be compatible with the specified test membranes. The range of application has been evaluated with oils of viscosity up to ISO viscosity grade (VG) 100, as defined in ISO 3448. Within the range described, the filterability as defined is not dependent on the viscosity of the oil. The procedure is not suitable for some hydraulic oils on which specific properties have been conferred by the use of insoluble/partially soluble additives, or by particularly large molecular species. NOTE Filterability is a prime requirement for lubricating oils used in hydraulic systems because of the fine filters used in this application. This part of ISO 13357 defines a method for assessing the filterability of oils in the presence of contaminating water. It should be noted that some oils will exhibit poorer filterability characteristics in these conditions. ISO 13357-2 should be used to investigate the filterability of an oil which is to be used in applications where the presence of water in the oil is unlikely. An oil which has good filterability in the presence of contaminating water will not necessarily have equally good filterability in dry conditions. An oil having good filterability only when wet is unlikely to be generally acceptable.

Petroleum products - Determination of the filterability of lubricating oils - Part 1: Procedure for oils in the presence of water (ISO 13357-1:2002)

NF T60-612-1*NF ISO 13357-1:2005 石油产品.润滑油可过滤性测定.第1部分:水中过滤油的程序

Petroleum products - Determination of the filtrability of lubricating oils - Part 1 : procedures for oils in presence of water.

SANS 1435:2004 含水金属加工液和液压用液体的乳液用生物杀灭剂

This specification covers three types of organic biocides (differentiated by their physical state -liquid, paste or solid) that are soluble in or miscible with water and oil and are intended for use in emulsions of aqueous metal working fluid and aqueous hydraulic fluid. NOTES a) The standards referred to in the specification are listed in appendix A. b) A requirement that must be specified by the purchaser is noted in appendix B. c) Information regarding the verification of the quality of biocides produced to this specification, and the sampling plan that can be used to assess compliance with the specification of a lot of biocide are given in appendix C.

Biocides for use in emulsions of aqueous metal working fluid and aqueous hydraulic fluid

BS 2000-313:2003 石油和石油产品的试验方法 BS 2000-313-2001液压油和润滑油的释气值测定

Methods of test for petroleum and its products. Determination of air release of lubricating and hydraulic oils

BS 2000-313:2001 石油和石油产品的试验方法.BS 2000-313-2001液压油和润滑油的释气值测定

This standard specifies a procedure for the determination of the measurement of the ability of turbine, gear and hydraulic oils to separate entrained air. It is applicable to both mineral and synthetic based products, but the current precision statement only applies to mineral oils. NOTE 1 - Agitation of lubricating and hydraulic oils with air in equipment such as bearings, couplings, gears, pumps and lines, can produce a dispersion of finely divided air bubbles in the oil. If the residence time in the reservoir is too short to allow the air bubbles to rise to the surface, a mixture of air and oil will circulate through the system. This may result in an inability to maintain oil pressure (particularly with centrifugal pumps), incomplete oil films in bearings and gears, and poor hydraulic system performance or failure. NOTE 2 - This standard measures the time for the entrained air content to fall to the relatively low value of 0,20 % [V/V] under a standardized set of test conditions, and hence permits the comparison of the ability of oils to separate entrained air under conditions where a separation time is available. Although the significance of the test results is not fully established, entrained air can cause sponginess and lack of sensitivity in the control of turbine and hydraulic systems. This standard may not be suitable for ranking oils in applications where residence times are short and gas contents are high.

Methods of test for petroleum and its products - BS 2000-313:2001 Determination of air release of lubricating and hydraulic oils (Identical with IP 313:2001)

BS ISO 13357-1:2002 石油产品.润滑油可过滤性测定.含水油过滤的程序

This part of ISO 13357 specifies a procedure for the evaluation of the filterability of lubricating oils, particularly those designed for hydraulic applications, in the presence of water. The procedure only applies to mineral-based oils, since fluids manufactured from other materials (e.g. fire-resistant fluids) may not be compatible with the specified test membranes. The range of application has been evaluated with oils of viscosity up to ISO viscosity grade (VG) 100, as defined in ISO 3448. Within the range described, the filterability as defined is not dependent on the viscosity of the oil. The procedure is not suitable for some hydraulic oils on which specific properties have been conferred by the use of insoluble/partially soluble additives, or by particularly large molecular species. NOTE Filterability is a prime requirement for lubricating oils used in hydraulic systems because of the fine filters used in this application. This part of ISO 13357 defines a method for assessing the filterability of oils in the presence of contaminating water. It should be noted that some oils will exhibit poorer filterability characteristics in these conditions. ISO 13357-2 should be used to investigate the filterability of an oil which is to be used in applications where the presence of water in the oil is unlikely. An oil which has good filterability in the presence of contaminating water will not necessarily have equally good filterability in dry conditions. An oil having good filterability only when wet is unlikely to be generally acceptable.

Petroleum products - Determination of the filterability of lubricating oils - Procedure for oils in the presence of water

ISO 13357-1:2002 石油产品.润滑油可过滤性测定.第2部分:水中过滤油的程序

This part of ISO 13357 specifies a procedure for the evaluation of the filterability of lubricating oils, particularly those designed for hydraulic applications, in the presence of water. The procedure only applies to mineral-based oils, since fluids manufactured from other materials (e.g. fire-resistant fluids) may not be compatible with the specified test membranes. The range of application has been evaluated with oils of viscosity up to ISO viscosity grade (VG) 100, as defined in ISO 3448. Within the range described, the filterability as defined is not dependent on the viscosity of the oil. The procedure is not suitable for some hydraulic oils on which specific properties have been conferred by the use of insoluble/partially soluble additives, or by particularly large molecular species. NOTE Filterability is a prime requirement for lubricating oils used in hydraulic systems because of the fine filters used in this application. This part of ISO 13357 defines a method for assessing the filterability of oils in the presence of contaminating water. It should be noted that some oils will exhibit poorer filterability characteristics in these conditions. ISO 13357-2 should be used to investigate the filterability of an oil which is to be used in applications where the presence of water in the oil is unlikely. An oil which has good filterability in the presence of contaminating water will not necessarily have equally good filterability in dry conditions. An oil having good filterability only when wet is unlikely to be generally acceptable.

Petroleum products - Determination of the filterability of lubricating oils - Part 1: Procedure for oils in the presence of water

ISO 13357-2:1998 石油产品 润滑油过滤性的测定 第2部分:对不含水油品的试验方法

This part of ISO 13357 specifies a procedure for the evaluation of the filterability of dry lubricating oils, particularly those designed for hydraulic applications. The procedure only applies to mineral-based oils, since fluids manufactured from other materials (e.g. fire-resistant fluids) may not be compatible with the specified test membranes. The range of application has been evaluated with oils of viscosity up to ISO viscosity grade (VG) 100, as defined in ISO 3448. Within the range described, the filterability as defined is not dependent on the viscosity of the oil. The procedure is not suitable for some hydraulic oils on which specific properties have been conferred by the use of insoluble/partially soluble additives, or by particularly large molecular species. NOTE — Filterability is a prime requirement for lubricating oils used in hydraulic systems because of the fine filters used in this application. This part of ISO 13357 defines a method for assessing the filterability of dry oils. It should be noted that some oils will exhibit degraded filterability characteristics in the Presence of contaminating water. 1SO 13357-1 should be used to investigate the effect of water and high temperature on filterability, if an oil is to be used in applications where the presence of water in the oil is likely.

Petroleum products - Determination of the filterability of lubricating oils - Part 2: Procedure for dry oils

CSN 65 6601-1984 工业用油．依据粘度的分类

Schválenie ST SEV 3969-83 odporu?ilo Ministerstvo priemyslu SSR, Bratislava. Spracovat?: Slovnaft, n. p. Bratislava — Marta Subjaková Odborové normaliza?ně st?edisko: Chemopetrol, G?, Praha Pracovník ??adu pro normalizaci a mě?ení: Ing. Emilie ?kardová

Industrial oils. Classification according to viscosity

NF T60-149:1979 石油产品.润滑油和液压油脱气时间的测定

PETROLEUM PRODUCTS. DETERMINATION OF AIR RELEASE TIME OF LUBRICANTS AND HYDRAULIC FLUIDS.

GOST 20734-1975 7-50C-3工作液体.技术条件

Настоящий стандарт распространяется на рабочую жидкость 7-50С-3, предназначенную для применения в гидроагрегатах и в гидросистемах при тем

Hydraulic fluid 7-50C-3. Specifications