83.040.20;83.060 标准查询与下载

JIS K 6239-1:2017 苯乙烯-丁二烯橡胶 (SBR). 溶聚苯乙烯-丁二烯橡胶微观结构的测定. 第1部分: 带有铸膜法的1H-NMR和IR

Styrene-butadiene rubber(SBR) -- Determination of the microstructure of solution-polymerized SBR -- Part 1: 1H-NMR and IR with cast-film method

JIS K 6239-2:2017 苯乙烯-丁二烯橡胶 (SBR). 溶聚苯乙烯-丁二烯橡胶微观结构的测定. 第2部分: ATR法的FTIR法

Styrene-butadiene rubber(SBR) -- Determination of the microstructure of solution-polymerized SBR -- Part 2: FTIR with ATR method

BS ISO 15672:2000 橡胶和橡胶添加剂.采用自动分析仪对含氮总量的测定

This International Standard specifies an instrumental (automatic analyser) method for the determination of total nitrogen in rubber and rubber additives.

Rubber and rubber additives - Determination of total nitrogen content using an automatic analyser

BS ISO 15671:2000 橡胶和橡胶添加剂.采用自动分析仪对含硫总量的测定

This International Standard specifies an instrumental (automatic analyser) method for the determination of total sul-fur in rubber and rubber additives.

Rubber and rubber additives - Determination of total sulfur content using an automatic analyser

ISO 15672:2000 橡胶和橡胶配合剂 用自动分析仪测定总氮含量

This International Standard specifies an instrumental (automatic analyser) method for the determination of total nitrogen in rubber and rubber additives.

Rubber and rubber additives - Determination of total nitrogen content using an automatic analyser

ISO 15671:2000 橡胶和橡胶配合剂 用自动分析仪测定总硫量

This International Standard specifies an instrumental (automatic analyser) method for the determination of total sul-fur in rubber and rubber additives.

Rubber and rubber additives - Determination of total sulfur content using an automatic analyser

ASTM D6370-99(2014) 用热重力法 (TGA) 对橡胶组成分析的标准试验方法

5.1 This test method is intended for use in quality control, material screening, and related problem solving where a compositional analysis, or comparison to a known material, is desired. 5.2 The parameters described are guidelines and may be altered to suit the analysis of other rubber compounds. 5.3 This test method is not suitable for rubber compounds containing filler materials which decompose in the temperature range of 50 to 800°C, for example, CaCO3, Al(OH)3(3H2O), etc. Analysis of compounds containing fillers of this type requires knowledge of the filler type and some correction for mass loss. 1.1 This test method provides a thermogravimetric (TGA) technique to determine the amounts of organics (oil, polymer), carbon black and ash (filler) in a rubber compound. 1.2 The amount of plasticizer/oil may be determined separately using Test Method D297. 1.3 This test method utilizes previously calibrated, manual or computer assisted TGA instrumentation. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber—Compositional Analysis by Thermogravimetry (TGA)

BS 5293:1976 橡胶工业用炭黑的取样和试验方法

Sampling bulk and packaged shipments. Determination of total sulphur content.

Methods for sampling and testing carbon black for use in the rubber industry

GOST 412-1976 橡胶混合物.《环》形模数测定法

Настоящий стандарт распространяется на резиновые смеси и устанавливает метод оценки вязкоупругих свойств испытуемого материала, завися

Rubber mixtures. Method for the determination of the ring modulus