默克密理博Milligard 过滤器

tel: 400-6699-117 转 1000

Milli-Q过滤器、超滤、微滤系统, Milligard过滤器由均匀的纤维素酯构成，由于其高截留率，并且不泄漏纤维的特点，Milligard成为拥有良好性能重......

在线客服

参数指标

我要提交参数指标我要纠错

规格

	Per 10-inch Cartridge
Filtration Area
Single Layer	0.8 m²
Double Layer	0.69 m²
Materials of Construction
Chemistry	Mixed Cellulose Esters (MCE)
Support Material	Polyester
Device Material	Polypropylene
Seal Material	Silicone (SI)
Maximum Differential Pressure, bar (psid)	3.5 bar (50 psid) @ 25 °C
Gravimetric Extractables
Standard Milligard® Media	The extractables level was equal to or less than 50 mg per 10-inch cartridge after 24 hours in water at controlled room temperature.
Low Protein Binding Milligard® Media, 0.2 µm	The extractables level was equal to or less than 100 mg per 10-inch cartridge after a 5 L flush and 24 hours in water at controlled room temperature.
Low Protein Binding Milligard® Media, 0.5 µm	The extractables level was equal to or less than 100 mg per 10-inch cartridge after a 5 L flush and 24 hours in water at controlled room temperature.
Low Protein Binding Milligard® Media, 1.2 µm	The extractables level was equal to or less than 250 mg per 10-inch cartridge after a 5 L flush and 24 hours in water at controlled room temperature.
Low Protein Binding Milligard® Media, 1.2/0.5 µm	The extractables level was equal to or less than 200 mg per 10-inch cartridge after a 5 L flush and 24 hours in water at controlled room temperature.
Low Protein Binding Milligard® Media, 1.2/0.5 µm	The extractables level was equal to or less than 350 mg per 10-inch cartridge after a 5 L flush and 24 hours in water at controlled room temperature.
Bacterial Endotoxins	Aqueous extraction contains ≤0.5 EU/mL as determined by the Limulus Amebocyte Lysate (LAL) Test
Oxidizable Substances	Will meet the USP Oxidizable Substances Test requirements after a water flush of ≥5 L
Sterilization	10 autoclave cycles or SIP @ 121 °C for 30 min
Component Material Toxicity	Component materials meet the criteria of the USP <88> Reactivity Test for Class VI Plastics. These products meet the requirements of the USP <88> Safety Test, utilizing a 0.9% sodium chloride extraction.
Good Manufacturing Practices	These products are manufactured in a facility which adheres to FDA Good Manufacturing Practices.
Non-Fiber Releasing	Component materials meet the “non-fiber releasing“ criteria as defined in 21 CFR 210.3 (b) (6).
Indirect Food Additive	All component materials meet the FDA Indirect Food Additive requirements cited in 21 CFR 177-182.

Typical Clean Water Flow Rate vs Pressure Drop

Cartridge Legends Refer to Pore Size (nominal):
Milligard Media
CW03 = 0.2 µm
CW06 = 0.5 µm
CW19 = 1.2 µm
CWSC = 1.2/0.5 µm
CWSS = 0.5/0.2 µm
Milligard LPB Media
CWL3 = 0.2 µm
CWL6 = 0.5 µm
CWL9 = 1.2 µm
CWLC = 1.2/0.5 µm
CWLS = 0.5/0.2 µm