我的咨询

您好,欢迎您查看分析测试百科网,请问有什么帮助您的?

稍后再说 立即咨询
咨询列表
荣计达仪器/rongjida
X
头像

客服中心

如果企业客服不在线,也可拨打400电话联系。或者发布求购信息

400-6699-117转1000
发布求购 平台客服
扫码下载
"来会会"App
扫码关注
分析测试百科网
您现在所在的位置:首页 >> 仪器导购 >> 水泥相关仪器>> 荣计达XSP硬质泡沫吸水率测定仪

荣计达XSP硬质泡沫吸水率测定仪

tel: 400-6699-117 1000

荣计达仪器/rongjida水泥相关仪器, 本产品具有使用简单、精确度高的特点。

咨询留言

技术特点

【技术特点】-- 荣计达XSP硬质泡沫吸水率测定仪

上海荣计达仪器科技有限公司专业经营水泥实验仪器、混凝土实验仪器、公路土工实验仪器、干粉砂浆保温砂浆实验仪器、沥青防水材料实验仪器、油漆涂料实验仪器、无损检测等实验仪器。专业经营水泥实验仪器、混凝土实验仪器、公路土工实验仪器、干粉砂浆保温砂浆实验仪器、沥青防水材料实验仪器、油漆涂料实验仪器、无损检测等实验仪器。公司产品凭借过硬的质量、完善的售后服务、合理的价格畅销各大院校、检测单位、建材企业、工程建设单位。在消费者当中享有较高的地位和良好的口碑,用户遍布国内近三十个省市、自治区,并远销国外,与用户建立了长期稳定的合作关系。公司实力雄厚,重信用、守合同。有健全的管理制度和完善健全的质量管理体系。并有反应迅速、服务周到的售后服务系统。我们将不懈努力、一如既往以优异的品质为客户服务。


硬质泡沫塑料吸水率测试系统是由:硬质泡沫塑料吸水率测试计算软件、试样装载专用网笼、测试样品水箱、硬质泡沫塑料质量测量仪、试样专用切片器、玻璃载片等六大部分组成。是根据国家标准GB8810-2005《硬质泡沫塑料吸水率检测》设计制造。具有使用简单、精确度高的特点,可被广泛使用于制造、科技的硬质泡沫塑料吸水率测试。

The rigid foam plastic water absorption test system is composed of: rigid foam plastic water absorption rate test calculation software, sample loading special net cage, test sample water tank, rigid foam plastic quality measuring instrument, sample special slicer, glass slide, etc. The six major components. It is designed and manufactured according to the national standard GB8810-2005 “hard foam plastic water absorption rate detection“. It has the characteristics of simple use and high precision, and can be widely used in the manufacturing and technology of rigid foam water absorption test.

一,测试方法

被测物尺寸:长度 150MM、宽度150mm、厚度 75mm;休积不大于500cm3;

环境温度:23±2℃      环境湿度:50±5﹪

泡水液:蒸馏后至少放置 48小时的蒸馏水;

将硬质泡沫切割成长 150MM宽 150毫米厚 75mm的正方形被测物。

将试样放于天平上,称量干燥后的试样重量(m1),准确至 0.1g,并记录。

悬挂网笼浸入蒸馏水中,除去悬挂网笼表层气泡,挂于天平的下称钩上,称其表现重量(m2),准确至 0.1g,并记录下来,记住后将悬挂网笼取下。

将悬挂网笼2边套筒上的2个固定螺钉分别拧松,再将试样安放圆盘上并居中;将压棒下调压住试样,压棒2端紧扣试样,并旋紧2边套筒上的两个固定螺钉。

将安装好试样的悬挂网笼重新浸入蒸馏水中,用软毛刷跟搅拌除去悬挂网笼和硬质泡沫表层气泡。

浸泡96小时后,将盛有试样的悬挂网笼挂于天平下称钩上,称量其表现质量(m3),准确至0.1g,并记住下来 。

Second, the test method
★Measurement object size: length 150MM, width 150mm, thickness 75mm; rest is not more than 500cm3;
★ Ambient temperature: 23±2°C Ambient humidity: 50±5%
★ soaking liquid: at least 48 hours of distilled water after distillation;
★ Cut the rigid foam into 150mm wide 150mm thick 75mm square measured object.
★ Place the sample on the balance and weigh the dried sample (m1) to the nearest 0.1g and record.
★The hanging net cage is immersed in distilled water to remove the air bubbles on the surface of the hanging net cage. It is hung on the lower hook of the balance, and its performance weight (m2) is called, accurate to 0.1g, and recorded, remember to take off the hanging net cage. .★ Loosen the two fixing screws on the sleeve of the hanging cage 2, and place the sample on the disc and center it; press the pressure rod down to press the sample, press the end of the pressure rod 2, and rotate Tightening the two setscrews on the two side sleeves.
★ Re-dip the hanging net cage with the sample installed into the distilled water, and use a soft brush to stir and remove the hanging net cage and the foam bubbles on the surface of the rigid foam.
★ After soaking for 96 hours, hang the hanging net cage containing the sample on the hook under the balance, weigh the performance quality (m3), accurate to 0.1g, and remember it.

硬质泡沫吸水率测定仪切片器

二,使用说明

硬质泡沫试样切片器是硬质泡沫塑料吸水率的一部分。

硬质泡沫试样切片器其主要结构有样品安放槽,样品厚度调节器,样品加紧螺丝,样品放置调节器的作用是:安放样品,并调节样品切片厚度。

Rigid foam water absorption meter slicer
First, the instructions for use
The rigid foam sample slicer is part of the water absorption of the rigid foam.
The main structure of the rigid foam sample slicer is a sample placement groove, a sample thickness adjuster, a sample tightening screw, and a sample placement adjuster for: placing a sample and adjusting the thickness of the sample slice.


三,使用方法:

1、将试件厚度调节器调节到25mm刻度处,松开样品加紧螺丝,将试件尺寸为50*50的样件放入安放槽内,旋紧样品夹紧螺丝压紧试件。

2、用切片刀沿切样器平台表面将多余的样品切除,为确保样品上部平整,可用切片厚度调节器调节出0.3mm,用切片刀将样品齐边。

3、切片厚度调节器调节出所需切片厚度(顺时针为挤出样品,逆时针为样品退回样品安放槽),但应加上刀刃的厚度,切片刀刃厚度约为0.15-0.2mm,例如:切0.1mm厚度时应旋出0.3mm左右,再用切片机进行切片。

Third, the method of use:
1. Adjust the thickness adjuster of the test piece to the 25mm mark, loosen the sample tightening screw, put the sample piece with the test piece size of 50*50 into the mounting groove, and tighten the sample clamping screw to press the test piece.
2. Use a slicing knife to cut the excess sample along the surface of the cutter platform. To ensure that the upper part of the sample is flat, the slice thickness adjuster can be used to adjust 0.3 mm, and the sample is trimmed with a slicing knife.
3. The slice thickness adjuster adjusts the required slice thickness (clockwise for the extruded sample and counterclockwise for the sample to return to the sample placement slot), but the thickness of the blade should be added. The sliced blade thickness is about 0.15-0.2mm, for example: When cutting 0.1mm thickness, it should be rotated about 0.3mm, and then sliced with a microtome.



【技术特点对用户带来的好处】-- 荣计达XSP硬质泡沫吸水率测定仪


【典型应用举例】-- 荣计达XSP硬质泡沫吸水率测定仪



售后服务

我会维修/培训/做方法

如果您是一名工程师或者专业维修科学 仪器的服务商,都可参与登记,我们的平台 会为您的服务精确的定位并展示。

1该产品的品牌知名度如何?
2你对该产品的使用感受如何?
3该产品的性价比如何?
4该产品的售务如何?
查看
    在线咨询

    在线咨询时间:

    周一至周五

    早9:00 - 晚17:30

    若您在周六周日咨询,请直接留言您所咨询的产品名称+联系人+电话