技术特点
【技术特点】-- 冠测SLYQ-96A/3路全自动聚乙烯压痕硬度测定仪
冠测SLYQ-96A/3路全自动聚乙烯压痕硬度测定仪
全自动聚乙烯压痕硬度测定仪
SLYQ-96A/3路
一、满足标准:
GB/T 23257-2009 埋地钢质管道聚乙烯防腐层
二、产品概述:
本仪器主要测试聚乙烯在一定的温度环境和恒定的压力下经过一定的时间后的压痕深度。
本仪器是国内自动化程度最高,最领先的测试聚乙烯压痕硬度的测试仪器,由于做的时间比较长,试验人员只需要在试验前设定好参数后,会自动根据设置的实验条件进行加温,并保持恒温,能够自动加载,并自动采集结果、计算平均数值。实验完成后有报警提示,报警时间长短可以设定!
三、产品特点:
1、本仪器核心控制部分通过7寸触摸屏设置参数并控制。
2、本仪器变形采集利用国内领先的微型位移传感器技术,淘汰了利用数字千分表采集位移精度低、易坏及需要更换电池等缺陷
3、设置好参数后,点开始实验后自动加载,实验结束后自动计算结果,同时压头自动复位到初始位置进行下次实验
4、 同时可以做三路实验,也可以单独进行一路或二路
5、 本仪器带有微型打印机,可以对试验结果进行打印,并自动计算平均值。
6、 测试环境温度为:室温-100度,温度可设定
7、 具有报警提示,实验完成后根据设定的报警时间进行报警。
四、主要配置及附件:
1、主 机: 一台
2、主机压头¢1.8mm: 三个
3、微型打印机: 一台
4、自动加载装置: 三套
5、位移传感器: 三个
6、恒温加热装置: 一套
7、使用说明书: 一份
8、德国西门子PLC: 一个
9、德国西门子采集模块:一个
10、寸彩色触摸屏: 一个
下面是产品英广版说明:
Full automatic polyethylene indentation hardness tester
SLYQ-96A/3 Road
One, meet the standards:
GB/T 23257-2009 polyethylene coating for buried steel pipeline
Two, product overview:
The instrument is mainly test of polyethylene in a definite temperature environment and the constant pressure after indentation depth after a certain time.
This instrument is the highest degree of automation, test instrument most leading testingpolyethylene indentation hardness, as a result of the relatively long time, test personnel only need to set parameters in the test before and after, will automatically according to the experimentalconditions set for heating, and keep constant temperature, automatic loading, automaticacquisition and calculation results, the average values. After completion of the experiment has alarm, alarm time can be set!
Three, product features:
1, the instrument is the core control part through a 7 Inch Touch screen set up parameters andcontrol.
2, the collection and utilization of micro displacement sensor deformation technology leading,eliminated using digital micrometer acquisition displacement precision is low, easily broken and the need to replace the battery and other defects
3, after parameter setting, some began to automatic loading experiment, automatic calculation results after the experiment, at the same time indenter automatic reset to the initial position for the next experiment
At the same time can do three experiments, can also be a road or two separate
The instrument with a micro printer, you can print the test results, and automatic calculation ofaverage value.
The test environment temperature: room temperature -100 degrees, the temperature can be set
With alarm, after completion of the experiment according to the set alarm time and alarm.
Four, the technical parameters:
1, the test load (25N): 10MP
2, the pressure head diameter: 1.8mm
3, temperature control precision is ± 0.5 degrees:
4, the indentation depth indicates the minimum scale value: 0.01mm
5, pressure time: you can set
6, the host deformation: ≤ 0.04mm
7, the effective value measurement range: can be set
8, to allow maximum thickness: 50MM
Five, the main configuration and accessories:
1, the main machine: a
2, the host head - 1.8mm: three
3, micro printer: a
4, automatic loading device: three sets
5, the displacement sensor: Three
6, a constant temperature heating device: a
7, the use of manual: a
8, Germany Siemens PLC: a
9, Germany Siemens acquisition module: a
10, inch color touch screen: a
【技术特点对用户带来的好处】-- 冠测SLYQ-96A/3路全自动聚乙烯压痕硬度测定仪
【典型应用举例】-- 冠测SLYQ-96A/3路全自动聚乙烯压痕硬度测定仪
经销商
除厂家/中国总经销商外,我们找不到 冠测SLYQ-96A/3路全自动聚乙烯压痕硬度测定仪 的一般经销商信息,有可能该产品在中国没有其它经销商。
如果您是,请告诉我们,我们的邮件地址是:sales@antpedia.net 请说明: 1.产品名称 2.公司介绍 3.联系方式 |
其他物性分析仪/测定仪
售后服务
我会维修/培训/做方法
如果您是一名工程师或者专业维修科学 仪器的服务商,都可参与登记,我们的平台 会为您的服务精确的定位并展示。