ELISPOT protocol
实验概要
The procedure below is a general guideline procedure for ELISPOT. Abcam ELISPOT kits have been designed for detection of various cytokines and growth factors from PBMC cells (Peripheral Blood Mononuclear cells). Optimized procedures are supplied with these kits and we recommend that these methods are used.
The researcher will, however, still need to optimize the cell numbers used, the length of cell culture incubation and the cell stimulant that is used.
ELISPOT pair products will require the researcher to use their own reagents and optimize the procedure.
实验原理
The Enzyme Linked Immunospot technique was developed by Cecil Czerkinskdy in 1983. ELISPOT is used for the detection of secreted proteins, such as cytokines and growth factors. It is therefore used primarily in immunology research in the following areas:
1. Transplantation – prediction of infectious risk
2. Vaccine development (IFN gamma)
3. Th1/Th2 analysis
4. Autoimmune disease
5. Cancer – tumor antigens
6. Allergy
7. Viral infection monitoring and treatment
Cells are grown in 96 well plates with antibody-coated PVDF or nitrocellulose membranes to the wells. First, the membrane is coated with primary antibody. Next, the cells are grown on this membrane and the secreted protein of interest will bind to the antibody. When this is detected using secondary antibody, the protein will be seen in the locality of that secreting cells as a spot of colour (one spot = 1 cell). The membranes are then scanned in and analyzed using one of various software programs that are available for this purpose. These are able to quantify the number and percentage of cells secreting the protein. Therefore, immune responses to various stimuli can be quantified and compared.
实验步骤
1. Prepare PVDF membranes in the 96 well plates by incubating in 70% ethanol for 30 seconds.
2. Coat 96 well ELISPOT plate with capture antibody (diluted in PBS). Incubate at 4°C overnight.
3. Empty the wells, tapping them dry, and wash with PBS
ELSIPOT plates should be handled more carefully than ELISA plates. When tapping dry, do this gently. Do NOT use plate washer at this stage. |
4. Block the plates by adding 100 ul per well 2% dry skim milk. Incubate 2 hours at room temperature.
5. Wash wells in PBS once
If necessary, the plates can be stored at this stage. Wash twice in PBS and leave to dry. Store at 4°C for not more than 2 weeks.
6. Prepare PBMCs from fresh blood on a Ficoll gradient. Count the cells (make sure they are over 95% viable). Dilute cells to the required concentration and add cell suspension to wells. If optimizing the assay for cell number, dilute 1:2 down the plate as in an ELISA. Do not shake the plates
The number of cells will require optimization. For example, if a low percentage of cells are expected to secrete the target cytokine, a larger cell number will be required. Refer to specific target kit protocols for recommendations on assay controls and cell number per well. Cell numbers should usually range between 1x105 to 2x105 cells per well.
7. Culture overnight 37°C in CO2 incubator. Do not shake the plates
*If cells take time to respond to stimulation, please see indirect method below.
1) Don’t move the plates while the cells are culturing. This will lead to ‘snail trail’ spots that will not be well defined. |
8. During the overnight incubation the cells will secrete cytokine, which will become bound to the primary antibody.
9. Wash cells and unbound cytokine away by incubating with PBS 0.1% Tween 20 for 10 minutes. Then wash the plates 3 times with PBS 0.1% Tween 20.
Ensure you include tween 20 in the wash buffer. Some cells will have started attaching after culture overnight (e.g some stem cells are known to do this). Tween 20 will help wash these off the membrane. Do not use a plate washer at this stage. |
10. Detect by using the conjugated secondary antibody (Dilute in PBS 1% BSA). Incubate for 1 to 2 hours at room temperature (optimization required)
11. Fluorescent detection / enzyme substrate color development
1) The base should be taken off the bottom of the plates washing between substrate and developing solution (e.g the wash between Streptavidin alkaline phosphatase conjugate and BICP/NBT development). Wash both sides of the membrane under running distilled water. This helps to prevent high background as some reagents can leak through the membrane into the bottom tray of the plate.
2) Monitor spot formation visually. As soon as the membranes look optimally developed, stop the reaction immediately by gently washing the plate. It is not a good idea to walk away while the spots are developing and the timing for optimal results will be slightly different each time.
12. Wash the plates in distilled water to stop the spot formation (take the base off the plates and wash both sides of the membrane).
13. Dry the plates and let membranes dry completely
Spots may become sharper if stored overnight at 4°C at this stage before reading. Membranes can be wrapped and stored at 47°C in the dark. |
14. Punch the membranes out of the wells onto a sticky plastic sheet. This step will depend on your plate reader’s requirements. Consult plate reader manual.
15. Scan the sheet and analyse the membrane circles analysed on the computer. Set parameters using the software so computer can distinguish spots:
Size/spot diameter
Intensity/saturation
Circularity/shape
Spot development/slope
These parameters can be set and saved, then used for repeated experiments for standardized results.
