01.040.19 试验 (词汇) 标准查询与下载

ASTM E1316-19b 无损检测的标准术语

Standard Terminology for Nondestructive Examinations

EN ISO 12718:2019 无损检测.涡流探伤.词汇

This document defines terms used in eddy current testing.

Non-destructive testing - Eddy current testing - Vocabulary (ISO 12718:2019)

ASTM E1316-19a 无损检测的标准术语

Standard Terminology for Nondestructive Examinations

ASTM E1316-19 无损检测的标准术语

Standard Terminology for Nondestructive Examinations

ASTM E1638-18 筛分法筛分和筛分介质的标准术语

Standard Terminology Relating to Sieves, Sieving Methods, and Screening Media

ASTM E1402-13(2018) 抽样设计标准指南

1.1 This guide defines terms and introduces basic methods for probability sampling of discrete populations, areas, and bulk materials. It provides an overview of common probability sampling methods employed by users of ASTM standards. 1.2 Sampling may be done for the purpose of estimation, of comparison between parts of a sampled population, or for acceptance of lots. Sampling is also used for the purpose of auditing information obtained from complete enumeration of the population. 1.3 No system of units is specified in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Sampling Design

ASTM E1316-17 无损检测的标准术语

Standard Terminology for Nondestructive Examinations

ASTM E1316-16 无损检测的标准术语

3.1 The terms found in this standard are intended to be used uniformly and consistently in all nondestructive testing standards. The purpose of this standard is to promote a clear understanding and interpretation of the NDT standards in which they are used. 1.1 This standard defines the terminology used in the standards prepared by the E07 Committee on Nondestructive Testing. These nondestructive testing (NDT) methods include: acoustic emission, electromagnetic testing, gamma- and X-radiology, leak testing, liquid penetrant testing, magnetic particle testing, neutron radiology and gauging, ultrasonic testing, and other technical methods. 1.2 Committee E07 recognizes that the terms examination, testing and inspection are commonly used as synonyms in nondestructive testing. For uniformity and consistency in E07 nondestructive testing standards, Committee E07 encourages the use of the term examination and its derivatives when describing the application of nondestructive test methods. There are, however, appropriate exceptions when the term test and its derivatives may be used to describe the application of a nondestructive test, such as measurements which produce a numeric result (for example, when using the leak testing method to perform a leak test on a component, or an ultrasonic measurement of velocity). Additionally, the term test should be used when referring to the NDT method, that is, Radiologic Testing (RT), Ultrasonic Testing (UT), and so forth. (Example: Radiologic Testing (RT) is often used to examine material to detect internal discontinuities.) 1.3 Section A defines terms that are common to multiple NDT methods, whereas, the subsequent sections define terms pertaining to specific NDT methods. 1.4 As shown on the chart below, when nondestructive testing produces an indication, the indication is subject to interpretation as false, nonrelevant or relevant. If it has been interpreted as relevant, the necessary subsequent evaluation will result in the decision to accept or reject the material. With the exception of accept and reject, which retain the meaning found in most dictionaries, all the words used in the chart are defined in Section A.

Standard Terminology for Nondestructive Examinations

ASTM E1316-16a 无损检测的标准术语

3.1 The terms found in this standard are intended to be used uniformly and consistently in all nondestructive testing standards. The purpose of this standard is to promote a clear understanding and interpretation of the NDT standards in which they are used. 1.1 This standard defines the terminology used in the standards prepared by the E07 Committee on Nondestructive Testing. These nondestructive testing (NDT) methods include: acoustic emission, electromagnetic testing, gamma- and X-radiology, leak testing, liquid penetrant testing, magnetic particle testing, neutron radiology and gauging, ultrasonic testing, and other technical methods. 1.2 Committee E07 recognizes that the terms examination, testing and inspection are commonly used as synonyms in nondestructive testing. For uniformity and consistency in E07 nondestructive testing standards, Committee E07 encourages the use of the term examination and its derivatives when describing the application of nondestructive test methods. There are, however, appropriate exceptions when the term test and its derivatives may be used to describe the application of a nondestructive test, such as measurements which produce a numeric result (for example, when using the leak testing method to perform a leak test on a component, or an ultrasonic measurement of velocity). Additionally, the term test should be used when referring to the NDT method, that is, Radiologic Testing (RT), Ultrasonic Testing (UT), and so forth. (Example: Radiologic Testing (RT) is often used to examine material to detect internal discontinuities.) 1.3 Section A defines terms that are common to multiple NDT methods, whereas, the subsequent sections define terms pertaining to specific NDT methods. 1.4 As shown on the chart below, when nondestructive testing produces an indication, the indication is subject to interpretation as false, nonrelevant or relevant. If it has been interpreted as relevant, the necessary subsequent evaluation will result in the decision to accept or reject the material. With the exception of accept and reject, which retain the meaning found in most dictionaries, all the words used in the chart are defined in Section A.

Standard Terminology for Nondestructive Examinations

ASTM E1325-16 有关实验设计的标准术语

3.1 This standard is a subsidiary to Terminology E456. 3.2 It provides definitions, descriptions, discussion, and comparison of terms. 1.1 This standard includes those statistical items related to the area of design of experiments for which standard definitions appear desirable.

Standard Terminology Relating to Design of Experiments

GSO ISO/TS 17822-1:2015 体外诊断测试系统 用于检测和鉴定微生物病原体的基于DNA的定性实验室分析程序 第1部分：一般要求、术语和定义

  Scope is not provided for this standard

In vitro diagnostic test systems -- Qualitative nucleic acid-based in vitro examination procedures for detection and identification of microbial pathogens -- Part 1: General requirements, terms and definitions

ASTM E6-15e1 与机械测试方法有关的标准术语

1.1 This terminology covers the principal terms relating to methods of mechanical testing of solids. The general definitions are restricted and interpreted, when necessary, to make them particularly applicable and practicable for use in standards requiring or relating to mechanical tests. These definitions are published to encourage uniformity of terminology in product specifications. 1.2 Terms relating to fatigue and fracture testing are defined in Terminology E1823. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Terminology Relating to Methods of Mechanical Testing

ASTM E6-15e2 与机械测试方法有关的标准术语

Standard Terminology Relating to Methods of Mechanical Testing

ASTM E6-15e4 与机械测试方法有关的标准术语

1.1 This terminology covers the principal terms relating to methods of mechanical testing of solids. The general definitions are restricted and interpreted, when necessary, to make them particularly applicable and practicable for use in standards requiring or relating to mechanical tests. These definitions are published to encourage uniformity of terminology in product specifications. 1.2 Terms relating to fatigue and fracture testing are defined in Terminology E1823. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Terminology Relating to Methods of Mechanical Testing

ASTM E6-15e3 与机械测试方法有关的标准术语

Standard Terminology Relating to Methods of Mechanical Testing

SL/T 13-2015 灌溉试验规程

Irrigation test procedures

SL 13-2015 灌溉试验规范

本标准适用于下列四类试验，对于不属于以上四类的试验，若其部分内容在本标准中做了规定，则这部分内容应符合本标准的要求： --作物及林、草蒸发蒸腾量观测试验； --作物及林、草灌溉制度试验； --作物劣态试验和灌溉效益试验； --灌水方法及灌水技术试验。

Specifications for irrigation experiment

ASTM F2078-15 有关氢脆化试验的标准术语

3.1 The terms used in describing hydrogen embrittlement have precise definitions. The terminology and its proper usage must be completely understood to communicate and transfer information adequately within the field. 3.2 The terms defined in other terminology standards, are respectively identified in parentheses following the definition. 1.1 This terminology covers the principal terms, abbreviations, and symbols relating to mechanical methods for hydrogen embrittlement testing, which are present in more than one of the standards under the jurisdiction of ASTM Committee F07 on Aerospace and Aircraft. These definitions are published to encourage uniformity of terminology in product specifications.

Standard Terminology Relating to Hydrogen Embrittlement Testing

ASTM E1316-15a 无损检测的标准术语

3.1 The terms found in this standard are intended to be used uniformly and consistently in all nondestructive testing standards. The purpose of this standard is to promote a clear understanding and interpretation of the NDT standards in which they are used. 1.1 This standard defines the terminology used in the standards prepared by the E07 Committee on Nondestructive Testing. These nondestructive testing (NDT) methods include: acoustic emission, electromagnetic testing, gamma- and X-radiology, leak testing, liquid penetrant testing, magnetic particle testing, neutron radiology and gauging, ultrasonic testing, and other technical methods. 1.2 Committee E07 recognizes that the terms examination, testing and inspection are commonly used as synonyms in nondestructive testing. For uniformity and consistency in E07 nondestructive testing standards, Committee E07 encourages the use of the term examination and its derivatives when describing the application of nondestructive test methods. There are, however, appropriate exceptions when the term test and its derivatives may be used to describe the application of a nondestructive test, such as measurements which produce a numeric result (for example, when using the leak testing method to perform a leak test on a component, or an ultrasonic measurement of velocity). Additionally, the term test should be used when referring to the NDT method, that is, Radiologic Testing (RT), Ultrasonic Testing (UT), and so forth. (Example: Radiologic Testing (RT) is often used to examine material to detect internal discontinuities.) 1.3 Section A defines terms that are common to multiple NDT methods, whereas, the subsequent sections define terms pertaining to specific NDT methods. 1.4 As shown on the chart below, when nondestructive testing produces an indication, the indication is subject to interpretation as false, nonrelevant or relevant. If it has been interpreted as relevant, the necessary subsequent evaluation will result in the decision to accept or reject the material. With the exception of accept and reject, which retain the meaning found in most dictionaries, all the words used in the chart are defined in Section A.

Standard Terminology for Nondestructive Examinations

ASTM E6-15 机械试验方法相关标准术语

1.1 This terminology covers the principal terms relating to methods of mechanical testing of solids. The general definitions are restricted and interpreted, when necessary, to make them particularly applicable and practicable for use in standards requiring or relating to mechanical tests. These definitions are published to encourage uniformity of terminology in product specifications. 1.2 Terms relating to fatigue and fracture testing are defined in Terminology E1823.

Standard Terminology Relating to Methods of Mechanical Testing