01.100.20 机械工程制图 标准查询与下载
共找到 332 条与 机械工程制图 相关的标准，共 23 页
ISO 10110 specifies the presentation of design and functional requirements for optical elements in technical drawings used for manufacturing and inspection. This part of ISO 10110 specifies rules for the indication of the surface texture of optical elements. Surface texture is the characteristic of a surface that can be effectively described with statistical methods. Typically, surface texture is associated with high spatial frequency errors (roughness) and mid-spatial frequency errors (waviness). This part of ISO 10110 is primarily intended for the specification of polished optics. This part of ISO 10110 describes a method for characterizing the residual surface that is left after detrending by subtracting the surface form. The control of the surface form is specified in ISO 10110-5 and ISO 10110-12, it is not specified in this part of ISO 10110.
Optics and photonics -- Preparation of drawings for optical elements and systems -- Part 8: Surface texture; roughness and waviness
- ICS
- 01.100.20
- CCS
- 发布
- 2014-12-25
- 实施
ISO 10110 specifies the presentation of design and functional requirements for optical elements and systems in technical drawings used for manufacturing and inspection. This part of ISO 10110 specifies rules for indicating centring tolerances for optical elements, subassemblies, and assemblies. They apply to rotationally symmetric optical systems only.
Optics and optical instruments -- Preparation of drawings for optical elements and systems -- Part 6: Centring tolerances
- ICS
- 01.100.20
- CCS
- 发布
- 2014-12-25
- 实施
ISO 10110 specifies the presentation of design and functional requirements for optical elements and systems in technical drawings used for manufacturing and inspection. This part of ISO 10110 specifies the indication of the tolerance for stress birefringence in optical elements made of isotropic material.
Optics and optical instruments -- Preparation of drawings for optical elements and systems -- Part 2: Material imperfections -- Stress birefringence
- ICS
- 01.100.20
- CCS
- 发布
- 2014-12-25
- 实施
The ISO 10110 series specifies the presentation of design and functional requirements for optical elements in technical drawings used for manufacturing and inspection. This part of ISO 10110 specifies rules for presentation, dimensioning and tolerancing of optically effective surfaces of aspheric form. This part of ISO 10110 does not apply to discontinuous surfaces such as Fresnel surfaces or gratings. This part of ISO 10110 does not specify the method by which compliance with the specifications is to be tested.
Optics and photonics -- Preparation of drawings for optical elements and systems -- Part 12: Aspheric surfaces
- ICS
- 01.100.20
- CCS
- 发布
- 2014-12-25
- 实施
ISO 8015:2011 specifies fundamental concepts, principles and rules valid for the creation, interpretation and application of all other International Standards, Technical Specifications and Technical Reports concerning geometrical product specifications (GPS) and verification. It applies to the interpretation of GPS indications on all types of drawings. For the purposes of ISO 8015:2011, the term "drawing" is to be interpreted in the broadest possible sense, encompassing the total package of documentation specifying the workpiece.
Geometrical product specifications (GPS) -- Fundamentals -- Concepts, principles and rules
- ICS
- 01.100.20
- CCS
- 发布
- 2014-12-25
- 实施
ISO 10110 specifies the presentation of design and functional requirements for optical elements and systems in technical drawings used for manufacturing and inspection. This part of ISO 10110 specifies rules for indicating the tolerance for surface form. NOTE 1 The terminology of interferometry is used for the specification of tolerances and, in particular, for the units in which the tolerances are to be specified; however, this does not stipulate that only interferometric methods may be used for the actual testing of optical parts. Other non-interferometric methods may be used if the results are converted to the units specified here. This part of ISO 10110 applies to surfaces of both spherical and aspheric form. NOTE 2 ISO 10110-12 allows the surface form tolerance for aspheric surfaces to be specified without reference to this part of ISO 10110.
Optics and photonics -- Preparation of drawings for optical elements and systems -- Part 5: Surface form tolerances
- ICS
- 01.100.20
- CCS
- 发布
- 2014-12-25
- 实施
ISO 10110 specifies the presentation of design and functional requirements for optical elements and systems in technical drawings used for manufacturing and inspection. This part of ISO 10110 specifies the permissible deviations and material imperfections when these are not explicitly indicated.
Optics and photonics -- Preparation of drawings for optical elements and systems -- Part 11: Non-toleranced data
- ICS
- 01.100.20
- CCS
- 发布
- 2014-12-25
- 实施
ISO 10110 specifies the presentation of design and functional requirements for optical elements and systems in technical drawings used for manufacturing and inspection. This part of ISO 10110 specifies rules for indicating the treatments and coatings applied to optical surfaces for functional and/or protective purposes.
Optics and optical instruments -- Preparation of drawings for optical elements and systems -- Part 9: Surface treatment and coating
- ICS
- 01.100.20
- CCS
- 发布
- 2014-12-25
- 实施
ISO 10110 specifies the presentation of design and functional requirements for optical elements in technical drawings used for manufacturing and inspection. This part of ISO 10110 specifies rules for the indication of allowable inhomogeneity and striae in optical elements.
Optics and optical instruments -- Preparation of drawings for optical elements and systems -- Part 4: Material imperfections -- Inhomogeneity and striae
- ICS
- 01.100.20
- CCS
- 发布
- 2014-12-25
- 实施
ISO 10110 specifies the presentation of design and functional requirements for optical elements and systems in technical drawings used for manufacturing and inspection. This part of ISO 10110 specifies the indication of the level of acceptability of bubbles and other inclusions in optical elements.
Optics and optical instruments -- Preparation of drawings for optical elements and systems -- Part 3: Material imperfections -- Bubbles and inclusions
- ICS
- 01.100.20
- CCS
- 发布
- 2014-12-25
- 实施
Technical drawings-Simplified representation of centre holes
- ICS
- 01.100.20
- CCS
- P50
- 发布
- 2014/12/23
- 实施
- 2014/12/23
Technical drawings-General principles of presentation-Part 24:Lines on mechanical engineering drawings
- ICS
- 01.100.20
- CCS
- J04
- 发布
- 2014/12/23
- 实施
- 2014/12/23
Technical drawings — Symbols for geometrical tolerancing — Proportions and dimension
- ICS
- 01.100.20
- CCS
- P50
- 发布
- 2014-12-23
- 实施
- 2014/12/23
Technical drawings — Simplified representation of center holes
- ICS
- 01.100.20
- CCS
- 发布
- 2014-12-23
- 实施
Technical drawings — Simplified representation of center holes
- ICS
- 01.100.20
- CCS
- 发布
- 2014-12-23
- 实施
Technical drawings — Simplified representation of bars and profile sections
- ICS
- 01.100.20
- CCS
- P50
- 发布
- 2014-12-23
- 实施
- 2014/12/23
Geometrical Product Specifications(GPS) — Drawing indications for moulded parts in technical product documentation(TPD)
- ICS
- 01.100.20
- CCS
- 发布
- 2014-12-17
- 实施
Technical drawings — General principles of presentation — Part 34: Views on mechanical engineering drawings
- ICS
- 01.100.20
- CCS
- J01
- 发布
- 2014-12-17
- 实施
- 2014/12/17
Technical drawings — General principles of presentation — Part 44: Sections on mechanical engineering drawings
- ICS
- 01.100.20
- CCS
- J01
- 发布
- 2014-12-17
- 实施
- 2014/12/17
Technical drawings — Dimensioning and tolerancing of profiles
- ICS
- 01.100.20
- CCS
- J04
- 发布
- 2014-12-17
- 实施
- 2014/12/17
