01.100.20 机械工程制图 标准查询与下载



共找到 332 条与 机械工程制图 相关的标准,共 23

This International Standard specifies a series of knurling dimensions intended for general use in mechanical engineering and is intended to avoid an unnecessary multiplicity of tools by restricting the profile angle to 90°and by a restricted selection of

Technical product documentation (TPD) - Dimensioning and indication of knurling

ICS
01.100.20
CCS
发布
2012-10-26
实施
2012-10-26

Technical product documentation (TPD). Dimensioning and indication of knurling

ICS
01.100.20
CCS
J04
发布
2012-08-31
实施
2012-08-31

This International Standard specifies a series of knurling dimensions intended for general use in mechanical engineering and is intended to avoid an unnecessary multiplicity of tools by restricting the profile angle to 90° and by restricting the selection of diametral pitches.

Technical product documentation (TPD) - Dimensioning and indication of knurling

ICS
01.100.20
CCS
J04
发布
2012-08
实施

Geometrical product specifications (GPS) - Dimensioning and tolerancing - Cones (ISO 3040:2009)

ICS
01.100.20
CCS
发布
2012-07-27
实施
2012-07-27

ISO 3040:2009 establishes the definition of cones and specifies the graphical symbol to be used for their indication and methods for their dimensioning and tolerancing.

Geometrical product specifications (GPS) - Dimensioning and tolerancing - Cones

ICS
01.100.20
CCS
发布
2012-05-03
实施
2012-05-03

Types and Applications of Engineering Drawings

ICS
01.100.20
CCS
J04
发布
2012
实施

Geometrical product specifications (GPS) - Dimensioning and tolerancing - Non-rigid parts; Technical Corrigendum 1

ICS
01.100.20
CCS
J04
发布
2011-12
实施

General requirements of three-dimensional modeling for mechanical products

ICS
01.100.20
CCS
发布
2011-12
实施

Geometrical product specifications (GPS) - Fundamentals - Concepts, principles and rules (ISO 8015:2011)

ICS
01.100.20
CCS
发布
2011-10-28
实施
2011-10-28

ISO 5459 describes the terminology, the rules, the explanations and the manner in which datums and datumsystems are indicated in technical product documentation.

Geometrical product specifications (GPS) - Geometrical tolerancing - Datums and datum systems

ICS
01.100.20
CCS
发布
2011-10-07
实施
2011-10-07

ISO 8015:2011 specifies fundamental concepts, principles and rules valid for the creation, interpretation and application of all other International Standards, Technical Specifications and Technical Reports concerning dimensional and geometrical product specifications (GPS) and verification.It applies to the interpretation of GPS indications on all types of drawings. For the purposes of ISO 8015:2011, the term """"drawing"""" is to be interpreted in the broadest possible sense, encompassing the total package of documentation specifying the workpiece.

Geometrical product specifications (GPS) - Fundamentals - Concepts, principles and rules

ICS
01.100.20
CCS
发布
2011-08-12
实施
2011-08-12

See Danish Scope

Basic Technical Drawing - Extracts from Standards

ICS
01.100.20
CCS
发布
2011-07-20
实施
2011-07-20

Geometrical product specifications (GPS) - Fundamentals - Concepts, principles and rules

ICS
01.100.20
CCS
A41
发布
2011-06
实施

Technical product documentation (TPD). General principles of presentation. Simplified representation for mechanical engineering drawings

ICS
01.100.20
CCS
J04
发布
2011-04-30
实施
2011-04-30

Representation of center hole

ICS
01.100.20
CCS
发布
2011-01-24
实施

Unified system of design documentation. Rules for presentation of kinematic diagrams

ICS
01.100.20
CCS
发布
2011
实施
2012-01-01

This part of ISO 128 specifies general principles and basic methods for the application of the simplifiedrepresentation on mechanical engineering drawings.The provisions of this part of ISO 128 are based on those of ISO 128-20, ISO 128-30, ISO 128-40, ISO 128-50,ISO 129-1 (Technical drawings — Indication of dimensions and tolerances — Part 1: General principles) andISO 6411 (Technical drawings — Simplified representation of centre holes).NOTE For the simplified representation of individual products, such as fastenings, springs, seals, gear wheels, racks,worms, worm gear-wheels, splint joints and rolling bearings, see the relevant International Standards.

Technical product documentation (TPD) - General principles of presentation - Part 71: Simplified representation for mechanical engineering drawings

ICS
01.100.20
CCS
发布
2010-11-05
实施
2010-11-05

Technical product documentation (TPD) - General principles of presentation - Part 71: Simplified representation for mechanical engineering drawings

ICS
01.100.20
CCS
J04
发布
2010-09
实施

Technical drawings for mechanical engineering

ICS
01.100.20
CCS
J04
发布
2010-04-20
实施

This standard specifies rules and conventions for the indications of requirements for moulded parts on technical product documentation. It also specifies the proportions and dimensions of the graphical symbols used for this representation.

Geometrical product specifications (GPS) - Drawing indications for moulded parts in technical product documentation (TPD)

ICS
01.100.20
CCS
发布
2009-06-22
实施
2009-06-22



Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号