03.120.30 统计方法的应用 标准查询与下载

DIN ISO 2859-2:2021 按属性检验的抽样程序 第2部分：用于隔离批检验的按限制质量（LQ）索引的抽样计划（ISO 2859-2:2020）

This document specifies an acceptance sampling system for inspection by attributes indexed by limiting quality (LQ). The sampling system is used for lots in isolation (isolated sequences of lots, an isolated lot, a unique lot or a short series of lots), where switching rules, suc

Sampling procedures for inspection by attributes - Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection (ISO 2859-2:2020)

21/30403747 DC BS ISO 3951-6 变量检验的抽样程序 第 6 部分：以限制质量 (LQ) 为索引的单次抽样计划规范 用于单一质量特性和单一 LQ 的隔离批次检验

BS ISO 3951-6. Sampling procedures for inspection by variables - Part 6. Specification for single sampling plans indexed by limiting quality (LQ) for isolated lot inspection for a single quality characteristic and a single LQ

DS/ISO 16355-1:2021 统计和相关方法在新技术和产品开发过程中的应用 第1部分：质量功能展开（QFD）的一般原则和观点

Application of statistical and related methods to new technology and product development process – Part 1: General principles and perspectives of quality function deployment (QFD)

ASTM E178-21 处理外围观测的标准实施规程

1.1 This practice covers outlying observations in samples and how to test the statistical significance of outliers. 1.2 The system of units for this standard is not specified. Dimensional quantities in the standard are presented only as illustrations of calculation methods. The examples are not binding on products or test methods treated. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Dealing With Outlying Observations

ASTM E2819-11(2021) 通过AQL索引的属性对产品流进行单级和多级连续采样的标准实践

1.1 This practice establishes tables and procedures for applying five different types of continuous sampling plans for inspection by attributes using MIL-STD-1235B as a basis for sampling a steady stream of lots indexed by AQL. 1.2 This practice provides the sampling plans of MIL-STD1235B in ASTM format for use by ASTM committees and others. It recognizes the continuing usage of MIL-STD-1235B in industries supported by ASTM. Most of the original text in MIL-STD-1235B is preserved in Sections 6 – 10 of this practice. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Single- and Multi-Level Continuous Sampling of a Stream of Product by Attributes Indexed by AQL

ASTM E2935-21 评价两种试验过程等效性的标准实施规程

1.1?This practice provides statistical methodology for conducting equivalence studies on numerical data from two sources of test results to determine if their true means, variances, or other parameters differ by no more than predetermined limits. 1.2?Applications include (1) eq

Standard Practice for Evaluating Equivalence of Two Testing Processes

ASTM D6299-21 应用统计质量保证和控制图表技术评估分析测量系统性能的标准实践

Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance

ISO 16355-1:2021 新技术和产品开发流程统计和相关方法的应用. 第1部分: 质量功能部署 (QFD) 通用原则和观点

This part of ISO 16355 describes the quality function deployment (QFD) process, its purpose, users, and tools. It does not provide requirements or guidelines for organizations to develop and systematically manage their policies, processes, and procedures in order to achieve specific objectives. Users of this part of ISO 16355 will include all organization functions necessary to assure customer satisfaction, including business planning, marketing, sales, research and development (R&D), engineering, information technology (IT), manufacturing, procurement, quality, production, service, packaging and logistics, support, testing, regulatory, and other phases in hardware, software, service, and system organizations.

Application of statistical and related methods to new technology and product development process - Part 1: General principles and perspectives of quality function deployment (QFD)

DB61/T 1453-2021 检验检测服务质量监测规范

本文件规定了检验检测服务质量监测的术语和定义、监测准备、监测实施、监测报告的要求。 本文件适用于监测检验检测机构的服务质量。

Inspection and testing service quality monitoring specification

DB61/T 1454-2021 特种设备隐患排查治理规范

本文件规定了特种设备隐患排查治理的术语和定义、基本要求、隐患分类、隐患排查、隐患治理、 及档案管理的要求。 本文件适用于特种设备使用单位隐患的排查和治理

Specifications for the investigation and management of hidden dangers in special equipment

BS ISO 16337:2021 统计及相关方法在新技术和产品开发过程中的应用 稳健的公差设计 (RTD)

What is ISO 16337 about?    ISO 16337 specifies guidelines for applying the robust tolerance design (RTD) provided by the Taguchi methods to a product to finalize the design of the product.   Note 1: RTD is applied to the target product to set the optimum tolerances of the design parameters around the nominal values. RTD identifies the effects of errors in the controllable design parameters on product output and estimates the total variance of the product output if the tolerances are changed. Hence, RTD achieves the target variance of the output from the viewpoints of robustness, performance, and cost.  Note 2: The tolerance expresses a maximum allowable error in the value of a design parameter in the manufacturing process. In a perfect world, the parts or elements of every product have the designed nominal values of the design parameters. However, actual manufacturing does not reproduce the exact designed nominal values of the design parameters for all products. The actual products have errors in the values of their parts or elements. These errors are supposed to be within the designed tolerances. 

Application of statistical and related methods to new technology and product development process. Robust tolerance design (RTD)

ISO 16337:2021 统计和相关方法在新技术和产品开发过程中的应用稳健公差设计（RTD）

This document specifies guidelines for applying the robust tolerance design (RTD) provided by the Taguchi methods to a product in order to finalize the design of the product. NOTE 1 RTD is applied to the target product to set the optimum tolerances of the design parameters around the nominal values. RTD identifies the effects of errors in the controllable design parameters on product output and estimates the total variance of the product output if the tolerances are changed. Hence, RTD achieves the target variance of the output from the viewpoints of robustness, performance, and cost. NOTE 2 The tolerance expresses a maximum allowable error in the value of a design parameter in the manufacturing process. In a perfect world, the parts or elements of every product have the designed nominal values of the design parameters. However, actual manufacturing does not reproduce the exact designed nominal values of the design parameters for all products. The actual products have errors in the values of their parts or elements. These errors are supposed to be within the designed tolerances.

Application of statistical and related methods to new technology and product development process — Robust tolerance design (RTD)

JIS Z 8405:2021 多个实验室间比较的方法测定熟练度的统计方法

Statistical methods for use in proficiency testing by interlaboratory comparison

KS Q ISO TR 13587:2021 测量不确定度评定和解释的三种统计方法

Three statistical approaches for the assessment and interpretation of measurement uncertainty

KS Q ISO TR 13587-2021 测量不确定度评定和解释的三种统计方法

Three statistical approaches for the assessment and interpretation of measurement uncertainty

KS Q ISO 16355-4-2021 统计和相关方法在新技术和产品开发过程中的应用.第4部分:非定量和定量客户声音和利益相关者声音的分析

Applications of statistical and related methods to new technology and product development process —Part 4: Analysis of non-quantitative and quantitative Voice of Customer and Voice of Stakeholder

KS Q ISO 22514-5-2021 过程管理中的统计方法.能力和性能.第5部分:属性特征的过程能力估计和性能

Statistical methods in process management —Capability and performance — Part 5: Process capability estimates and performance for attributive characteristics

KS Q ISO 16355-2:2021 统计和相关方法在新技术和产品开发过程中的应用.第2部分:获取客户声音和利益相关者声音的非定量方法

Applications of statistical and related methods to new technology and product development process —Part 2: Non-quantitative approaches for the acquisition of voice of customer and voice of stakeholder

KS Q ISO 16355-2-2021 统计和相关方法在新技术和产品开发过程中的应用.第2部分:获取客户声音和利益相关者声音的非定量方法

Applications of statistical and related methods to new technology and product development process —Part 2: Non-quantitative approaches for the acquisition of voice of customer and voice of stakeholder

KS Q ISO 22514-5:2021 过程管理中的统计方法.能力和性能.第5部分:属性特征的过程能力估计和性能

Statistical methods in process management —Capability and performance — Part 5: Process capability estimates and performance for attributive characteristics