11.080.20 消毒剂和防腐剂 标准查询与下载

ASTM E1054-21e1 抗菌剂灭活剂评价的标准实施规程

Standard Practices for Evaluation of Inactivators of Antimicrobial Agents

T/CAS 470-2021 乙醇消毒剂（气雾剂型）

1　范围 本标准规定了乙醇消毒剂（气雾剂型）的要求、试验方法、应用范围、使用方法、检验规则、标志、包装、运输和贮存。 本标准适用于在铁（铝）制气雾罐内填充了抛射剂和 75 %（v/v）乙醇原料的气雾剂型乙醇消毒剂。 2　规范性引用文件 下列文件对于本文件的应用是必不可少的。凡是注日期的引用文件，仅注日期的版本适用于本文件。凡是不注日期的引用文件，其最新版本（包括所有的修改单）适用于本文件。 GB/T 2828.1—2012　计数抽样检验程序 第1部分：按接收质量限（AQL）检索的逐批检验抽样计划 GB/T 2829—2002  周期检验计数抽样程序及表（适用于对过程稳定性的检验） GB 13042  包装容器 铁质气雾罐  GB/T 14449—2017  气雾剂产品测试方法 GB/T 17447  气雾阀 GB/T 25164  包装容器25.4 mm口径铝气雾罐 GB 26373—2020  醇类消毒剂卫生要求 GB 27949  医疗器械消毒剂通用要求 GB 27950  手消毒剂通用要求 GB 27951  皮肤消毒剂卫生要求 GB 27952  普通物体表面消毒剂通用要求 GB 28644.2  危险货物有限数量及包装要求 GB 30000.4  化学品分类和标签规范 第4部分：气溶胶 GB 31640  食品安全国家标准 食用酒精 BB/T 0005  气雾剂产品的标示、分类及术语 BB/T 0006  包装容器20 mm口径铝气雾罐 QB 2549—2002  一般气雾剂产品的安全规定 JJF 1070　定量包装商品净含量计量检验规则 WS 310.2  医院消毒供应中心 第2部分：清洗消毒剂灭菌技术操作规范 T/CAS 420—2020　车用零部件溶剂清洗气雾剂（轻垢型）

Ethanol-based disinfectant (Aerosol type)

PN-EN 17111-2018-12 P 化学消毒剂和防腐剂—医用器械杀病毒活性评价用定量载体试验—试验方法和要求（第2阶段第2步）

Chemical disinfectants and antiseptics -- Quantitative carrier test for the evaluation of virucidal activity for instruments used in the medical area -- Test method and requirements (phase 2, step 2)

prEN 16616-2020 化学消毒剂和防腐剂 化学-热纺织品消毒 试验方法和要求（第 2 阶段，第 2 步）

Chemical disinfectants and antiseptics - Chemical-thermal textile disinfection - Test method and requirements (phase 2, step 2)

OENORM EN 14885-2020 化学消毒剂和防腐剂 欧洲化学消毒剂和防腐剂标准的应用

Chemical disinfectants and antiseptics - Application of European Standards for chemical disinfectants and antiseptics

BS EN 13697:2015+A1:2019 化学消毒剂和防腐剂，用于评价食品、工业、家庭和机构领域中使用的化学消毒剂的杀菌和/或杀真菌活性的定量无孔表面试验 试验方法及要求w

Chemical disinfectants and antiseptics, Quantitative non-porous surface test for the evaluation of bactericidal and/or fungicidal activity of chemical disinfectants used in food, industrial, domestic and institutional areas. Test method and requirements w

NF T72-700*NF EN 13623:2020 化学消毒剂和防腐剂. 水溶液系统使用的化学消毒剂的抗军团杆菌杀菌活性的评定用定量悬浮试验. 要求和试验方法(相位2,阶1).

Domaine d'applicationLe présent document décrit une méthode d'essai et les prescriptions minimales relatives à l'activité bactéricide des produits désinfectants chimiques destinés au traitement des systèmes aqueux vis-à-vis de Legionella pneumophila et donnant une préparation hom

Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of bactericidal activity against Legionella of chemical disinfectants for aqueous systems - Test method and requirements (phase 2, step 1)

T/SICCA 010-2020 空气净化用电解水

    本标准主要技术内容包含了空气净化用电解水的生产用水、感官指标、性能指标（理化性能：pH值、有效氯浓度、氧化还原电位。净化性能：甲醛、甲苯、抗菌性能、除臭性能）、有害物质限量、安全性、稳定性等方面的要求。

Electrolyzed water for purifying air

T/NAHIEM 23-2020 中国儿童消毒剂标准

本标准规定了中国儿童消毒剂的物理指标要求、杀灭微生物要求、现场或模拟现场杀菌能力要求、安全性要求、腐蚀性要求、使用范围和方法、检验方法、检验规则、标志、包装、运输、贮存、说明书以及使用注意事项。

China Children's Disinfectant Standard

GSO EN 12791:2020 化学消毒剂和防腐剂 外科手消毒 测试方法和要求（第 2 阶段 步骤 2）

This European Standard specifies a test method simulating practical conditions for establishing whether a product for surgical handrub and handwash reduces the release of resident and eventually present transient microbial flora on hands when used for the treatment of clean hands of volunteers. This European Standard applies to products for surgical handrub or handwash for use in areas and situations where disinfection is medically indicated. Such indications occur in patient care, for example: - in hospitals, in community medical facilities and in dental institutions; - in clinics of schools, of kindergartens and of nursing homes. and may occur in the workplace and in the home. It may also include services such as laundries and kitchens supplying products directly for the patient. EN 14885 specifies in detail the relationship of the various tests to one another and to "use recommendations". NOTE This method corresponds to a phase 2, step 2 test.

Chemical disinfectants and antiseptics - Surgical hand disinfection - Test method and requirements (phase 2, step 2)

GSO EN 1500:2020 化学消毒剂和防腐剂 卫生洗手液 测试方法和要求（第 2 阶段/步骤 2）

This European Standard specifies a test method simulating practical conditions for establishing whether a product for hygienic handrub reduces the release of transient microbial flora on hands when rubbed onto the artificially contaminated hands of volunteers. NOTE 1 Attention is drawn to the fact that tests on human volunteers are the subject of legal provisions in certain European countries/regions. This European Standard applies to products for hygienic handrub for use in areas and situations where disinfection is medically indicated. Such indications occur in patient care, for example: - in hospitals, in community medical facilities and in dental institutions, - in clinics of schools, of kindergartens and of nursing homes; and may occur in the workplace and in the home. It may also include services such as laundries and kitchens supplying products directly for the patient. EN 14885 specifies in detail the relationship of the various tests to one another and to "use recommendations". NOTE 2 This method corresponds to a phase 2, step 2 test.

Chemical disinfectants and antiseptics - Hygienic handrub - Test method and requirements (phase 2/step 2)

GSO EN 1499:2020 化学消毒剂和防腐剂 卫生洗手 测试方法和要求（第 2 阶段/步骤 2）

This European Standard specifies a test method simulating practical conditions for establishing whether a product for hygienic handwash reduces the release of transient microbial flora on hands when used to wash the artificially contaminated hands of volunteers. NOTE 1 Attention is drawn to the fact that tests on human volunteers are the subject of legal provisions in certain European countries/regions. This European Standard applies to products for hygienic handwash for use in areas and situations where disinfection is medically indicated. Such indications occur in patient care, for example: - in hospitals, in community medical facilities and in dental institutions, - in clinics of schools, of kindergartens and of nursing homes; and may occur in the workplace and in the home. It may also include services such as laundries and kitchens supplying products directly for the patient. EN 14885 specifies in detail the relationship of the various tests to one another and to "use recommendations". NOTE 2 This method corresponds to a phase 2, step 2 test.

Chemical disinfectants and antiseptics - Hygienic handwash - Test method and requirements (phase 2/step 2)

T/DLYP 001-2020 《乙醇消毒剂生产技术规范》团体标准

为创建产业发展和企业良好的生产秩序，以标准引领产品质量提升，加强对乙醇消毒剂生产、包装、储存等过程中的安全、规范性的操作要领和经验，让企业更科学、更规范地组织生产，形成产业核心竞争力。

"Technical Specifications for the Production of Alcohol Disinfectants" Group Standard

ASTM E1839-20 造纸工业用杀粘剂效力的标准实施规程&x2014；细菌和真菌粘液

1.1 This practice presents a procedure to evaluate the efficacy of slimicides for the control of bacterial and fungal slimes in paper mill systems and their counterparts. 1.2 It is the responsibility of the investigator to determine whether Good Laboratory Practices (GLP) are required and to follow them where appropriate (40 CFR 160). 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Efficacy of Slimicides for the Paper Industry—Bacterial and Fungal Slime

19/30396906 DC BS EN 17430 化学消毒剂和防腐剂 卫生洗手液具有杀病毒作用 测试方法和要求（第2阶段/步骤2）

BS EN 17430. Chemical disinfectants and antiseptics. Hygienic handrub virucidal. Test method and requirements (phase 2/step 2)

DIN EN 14476:2019 化学消毒剂和防腐剂.人用药物中化学消毒剂和防腐剂的病毒定量悬浮试验.试验方法和要求(阶段2,第1步).德文版本EN 14476-2013+A1-2015

Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of virucidal activity in the medical area - Test method and requirements (Phase 2/Step 1); German version EN 14476:2013+A1:2015

BS EN 17126:2018 化学消毒剂和防腐剂 定量悬浮试验用于评价医疗领域化学消毒剂的杀孢子活性 测试方法和要求（第2阶段 步骤1）

What is BS EN 17126- Sporicidal activity of chemical disinfectants for medical areas about?    BS EN 17126 is a European standard that discusses chemical disinfectants and antiseptics. It provides the best industry guidance on the evaluation of the sporicidal activity of chemical disinfectants and antiseptics in the medical area to prevent transmission of any infectious disease and meet a safe and healthy environment.   BS EN 17126 layouts a test method and the minimum requirements for sporicidal activity of chemical disinfectant that form a homogeneous, physically stable preparation when diluted with hard water, or - in the case of ready-to-use products - with water. Products can only be tested at a concentration of 80 % or less (97 % wi...

Chemical disinfectants and antiseptics. Quantitative suspension test for the evaluation of sporicidal activity of chemical disinfectants in the medical area. Test method and requirements (phase 2, step 1)

BS EN 16777:2018 化学消毒剂和防腐剂 无机械作用的定量无孔表面测试 用于评估医疗领域使用的化学消毒剂的杀病毒活性 测试方法和要求（第2阶段/步骤2）

What is BS EN 16777- Quantitative non-porous surface test about?    BS EN 16777 is a European standard that discusses chemical disinfectants and antiseptics. It provides the best industry on the quantitative non-porous surface test for the evaluation of the virucidal activity of chemical disinfectants and antiseptics used in the medical area to prevent the transmission of any infectious disease and meet a safe and healthy environment.    BS EN 16777 layouts test method and the minimum requirements for virucidal activity of chemical disinfectants that form a homogeneous physically stable preparation when diluted with hard water – or in the case of ready-to-use products - with water. BS EN 16777 applies to products that are used in the medical area for disinfecting non-porous  

Chemical disinfectants and antiseptics. Quantitative non-porous surface test without mechanical action for the evaluation of virucidal activity of chemical disinfectants used in the medical area. Test method and requirements (phase 2/step 2)

BS EN 17111:2018 化学消毒剂和防腐剂 用于评估医疗领域使用的仪器的杀病毒活性的定量载体测试 测试方法和要求（第2阶段 步骤2）

What is BS EN 17111- Virucidal activity for instruments used in the medical area about?    BS EN 17111 is a European standard that discusses chemical disinfectants and antiseptics. It provides the best industry guidance on the evaluation of virucidal activity for instruments used in the medical area to prevent transmission of any infectious disease and meet a safe and healthy environment   BS EN 17111 layouts a test method and the minimum requirements for virucidal activity of chemical disinfectant products that form a homogeneous, physically stable preparation when diluted with hard water – or in the case of ready-to-use products – with water.   BS EN 17111 applies to products that are used in the medical area for disinfecting instruments by immersion. It also applies to areas and situations where disinfection ...

Chemical disinfectants and antiseptics. Quantitative carrier test for the evaluation of virucidal activity for instruments used in the medical area. Test method and requirements (phase 2, step 2)

ASTM E3178-18 用离心过滤管评价静态和杀灭化学去污剂对芽孢杆菌的作用

1.1 This practice is used to quantify the efficacy of liquid or solid decontaminants on Bacillus spores dried on the surface of coupons made from porous and non-porous materials. This practice can distinguish between bactericidal and bacteriostatic chemicals within decontamination mixtures. This is important because many decontaminants contain both reactive compounds and high concentrations of bacteriostatic surfactants. All test samples are directly compared to pre-neutralized controls, un-inoculated negative growth controls, and solution controls on the same day as the test in order to increase practical confidence in the inactivation data. 1.2 This procedure should be performed only by those trained in microbiological techniques, are familiar with antimicrobial (sporicidal) agents and the application instructions of the antimicrobial products. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Evaluating Static and Cidal Chemical Decontaminants against Bacillus Spores using Centrifugal Filtration Tubes