13.040.30 工作场所空气 标准查询与下载

ISO 8518:2022 工作场所空气.颗粒铅和铅化合物的测定.火焰和电热原子吸收光谱法

Workplace air — Determination of particulate lead and lead compounds — Flame and electrothermal atomic absorption spectrometric methods

EN ISO 13137:2022 工作场所空气.化学和生物制剂个人采样泵.要求和试验方法

This document specifies performance requirements for battery powered pumps used for personal sampling of chemical and biological agents in workplace air. It also specifies test methods in order to determine the performance characteristics of such pumps under prescribed laboratory conditions. This document is applicable to battery powered pumps having a nominal volumetric flow rate above 10 ml ⋅ min−1, as used with combinations of sampler and collection substrate for sampling of gases, vapours, dusts, fumes, mists and fibres. This document is primarily intended for flow-controlled pumps.

Workplace atmospheres - Pumps for personal sampling of chemical and biological agents - Requirements and test methods (ISO 13137:2022)

BS ISO 21438-1:2022 职场氛围 离子色谱法测定无机酸 非挥发性酸（硫酸和磷酸）

1   Scope This document specifies a method for the determination of the time-weighted average mass concentration of sulfuric acid and phosphoric acid in workplace air by ion chromatography. The anions are detected by conductivity. The method is applicable to the personal sampling of airborne particles, as defined in ISO 7708, and to static (area) sampling. The method does not apply to the determination of sulfur trioxide. The procedure does not differentiate between the acids and their corresponding salts if both are present in the workplace air. The procedure does not differentiate between phosphoric acid and diphosphorus pentoxide (phosphoric anhydride) if both are present in the workplace air.

Workplace atmospheres. Determination of inorganic acids by ion chromatography. Non-volatile acids (sulfuric acid and phosphoric acid)

DB65/T 4526-2022 工作场所空气有毒物质23种金属及其化合物测定电感耦合等离子体质谱法

Determination of 23 kinds of metals and their compounds in workplace air toxic substances by inductively coupled plasma mass spectrometry

ISO 23861:2022 工作场所空气.气载颗粒和蒸汽混合物中的化学试剂.使用取样器评估测量程序的要求

Workplace air — Chemical agent present as a mixture of airborne particles and vapour — Requirements for evaluation of measuring procedures using samplers

ASTM D5156-22 环境、工作场所和室内大气中臭氧连续测量的标准试验方法（紫外线吸收）

1.1 This test method describes the sampling and continuous analysis of ozone (O3) in the atmosphere at concentrations ranging from 10 to 2000 µg/m3 of O3 in air (5 ppb(v) to 1 ppm(v)). 1.1.1 The test method is limited to applications by its sensitivity to interferences as described in Section 6. The interference sensitivities may limit its use for ambient and workplace atmospheres. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Continuous Measurement of Ozone in Ambient, Workplace, and Indoor Atmospheres (Ultraviolet Absorption)

ASTM D7202-22 用萃取和光学荧光检测法测定工作场所中铍的标准试验方法

1.1 This test method is intended for use in the determination of beryllium by sampling workplace air and surface dust. 1.2 This test method assumes that air and surface samples are collected using appropriate and applicable ASTM International standard practices for sampling of workplace air and surface dust. These samples are typically collected using air filter sampling, vacuum sampling or wiping techniques. See Guide E1370 for guidance on air sampling strategies, and Guide D7659 for guidance on selection of surface sampling techniques. 1.3 Determination of beryllium in soil is not within the scope of this test method. See Test Method D7458 for determination of beryllium in soil samples. 1.4 This test method includes a procedure for extraction (dissolution) of beryllium in weakly acidic medium (pH of 1 % aqueous ammonium bifluoride is 4.8), followed by field analysis of aliquots of the extract solution using a berylliumspecific-optically fluorescent dye. 1.5 The procedure is suitable for on-site use in the field for occupational and environmental hygiene monitoring purposes. The method is also applicable for use in fixed-site laboratories. 1.6 No detailed operating instructions are provided because of differences among various makes and models of suitable fluorometric instruments. Instead, the analyst shall follow the instructions provided by the manufacturer of the particular instrument. This test method does not address comparative accuracy of different devices or the precision between instruments of the same make and model. 1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.8 This test method contains notes that are explanatory and not part of mandatory requirements of the standard. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Beryllium in the Workplace by Extraction and Optical Fluorescence Detection

ISO 13137:2022 工作场所空气.化学和生物制剂个人取样用泵.要求和试验方法

Workplace atmospheres — Pumps for personal sampling of chemical and biological agents — Requirements and test methods

ANSI/CAN/UL/ULC 4402:2022 用于大麻种植和收获后加工的建筑物和设施的室内空气质量

1.1 This Standard provides minimum indoor air quality (IAQ) requirements and guidelines for a building or portions of a building utilized for cannabis cultivation, post-harvest processing as well as ancillary spaces. Note: For the purposes of this Standard, ancillary spaces include areas that support the general operations required to run a cannabis facility. Examples include but are not limited to: Corridors, HVAC/Mechanical Rooms and Electrical Rooms. 1.2 This Standard recognizes the issues surrounding lead paint and asbestos in the built environment. Due to differing legal restrictions and licensure requirements, these materials are beyond the scope of this standard. It is the responsibility of the building owner and/or operator to assure compliance with all regulations applicable within the jurisdiction. 1.3 This Standard does not address: fumigation and insecticidal fogging, ozone generating air cleaning devices, ultraviolet germicidal irradiation (UVGI) exposure from air cleaning devices, nor exposure limits for hydrofluoroalkane (HFA-134a). 1.4 This Standard does not address cannabis related biogenic volatile organic compounds (BVOCs). These BVOCs include thiols (also called volatile sulfur compounds, or VSCs) as part of their natural biological cycles. The VOCs emitted by cannabis include terpenes with main constituents as isoprene, monoterpenes and sesquiterpenes. These terpenes are odorants with extremely low odor thresholds. At the time of this publication, the STP is not aware of any evidence that suggests health hazards are related to cannabis BVOC emissions at the typically observed concentrations. 1.5 This Standard does not include provisions for greenhouses.

Indoor Air Quality in Buildings and Facilities Utilized for the Cultivation and Post-Harvest Processing of Cannabis

BS EN ISO 23320:2022 工作场所空气 气体和蒸气 使用扩散采样器评估测量程序的要求

1   Scope This document specifies performance requirements and test methods under prescribed laboratory conditions for the evaluation of diffusive samplers (see Reference [1]) and of procedures using these samplers for the determination of gases and vapours in workplace atmospheres (see Reference [2]). This document is applicable to diffusive samplers and measuring procedures using these samplers, such as ISO 16200‑2 and ISO 16017‑2, in which sampling and analysis are carried out in separate stages. This document is not applicable to — diffusive samplers which are used for the direct determination of concentrations, and — diffusive samplers which rely on sorption into a liquid. This document addresses requirements for method developers and/or manufacturers. NOTE For the purposes of this document a manufacturer can be any commercial or non-commercial entity.

Workplace air. Gases and vapours. Requirements for evaluation of measuring procedures using diffusive samplers

ISO 21438-1:2022 工作场所空气.用离子色谱法测定无机酸.第1部分:非挥发性酸（硫酸和磷酸）

This document specifies a method for the determination of the time-weighted average mass concentration of sulfuric acid and phosphoric acid in workplace air by ion chromatography. The anions are detected by conductivity. The method is applicable to the personal sampling of airborne particles, as defined in ISO 7708, and to static (area) sampling. The method does not apply to the determination of sulfur trioxide. The procedure does not differentiate between the acids and their corresponding salts if both are present in the workplace air. The procedure does not differentiate between phosphoric acid and diphosphorus pentoxide (phosphoric anhydride) if both are present in the workplace air.

Workplace atmospheres — Determination of inorganic acids by ion chromatography — Part 1: Non-volatile acids (sulfuric acid and phosphoric acid)

T/CAB 0149-2022 场馆生物气溶胶监控处置系统技术要求

2.1.1工作条件 2.1.2技术要求 2.1.2.1  监控系统技术要求 2.1.2.1.1  外观要求 2.1.2.1.2  监控项目要求 2.1.2.1.3  运行环境要求 2.1.2.1.4  生物气溶胶采样器技术要求 1）仪器工作模式 2）采样效率 3）工作噪声 4）平均无故障时间 2.1.2.1.5  生物危害因子检测工作站技术要求 1）工作站工作环境要求 2）前处理模块升温速度要求 3）核酸检测模块要求 2.1.2.1.6  生物危害因子消杀器技术要求 1）主要元器件紫外线灯 2）紫外线强度 3）紫外线强度波动范围 4）有效寿命 5）工作噪声 6）消毒效果 2.1.2.2  生物气溶胶物联网云平台技术要求 1）可视化监视屏幕 2）调控要求 3）云端服务器 4）数据传输 2.1.2.3  监控处置系统运行要求 1）人员要求 2）监控样本量及监控频次 3）安装及布点要求 2.1.2.34  电气安全 2.1.2.35  电磁兼容

Technical requirements for the stadiums bioaerosol monitor and treatment system

EN ISO 23320:2022 工作场所空气.气体和蒸汽.使用扩散取样器的测量程序评估要求

This document specifies performance requirements and test methods under prescribed laboratory conditions for the evaluation of diffusive samplers (see Reference [1]) and of procedures using these samplers for the determination of gases and vapours in workplace atmospheres (see Reference [2]). This document is applicable to diffusive samplers and measuring procedures using these samplers, such as ISO 16200‑2 and ISO 16017‑2, in which sampling and analysis are carried out in separate stages. This document is not applicable to — diffusive samplers which are used for the direct determination of concentrations, and — diffusive samplers which rely on sorption into a liquid. This document addresses requirements for method developers and/or manufacturers. NOTE For the purposes of this document a manufacturer can be any commercial or non-commercial entity.

Workplace air - Gases and vapours - Requirements for evaluation of measuring procedures using diffusive samplers (ISO 23320:2022)

ISO 23320:2022 工作场所空气.气体和蒸汽.使用扩散取样器的测量程序评估要求

This document specifies performance requirements and test methods under prescribed laboratory conditions for the evaluation of diffusive samplers (see Reference [1]) and of procedures using these samplers for the determination of gases and vapours in workplace atmospheres (see Reference [2]). This document is applicable to diffusive samplers and measuring procedures using these samplers, such as ISO 16200-2 and ISO 16017-2, in which sampling and analysis are carried out in separate stages. This document is not applicable to — diffusive samplers which are used for the direct determination of concentrations, and — diffusive samplers which rely on sorption into a liquid. This document addresses requirements for method developers and/or manufacturers. NOTE For the purposes of this document a manufacturer can be any commercial or non-commercial entity.

Workplace air — Gases and vapours — Requirements for evaluation of measuring procedures using diffusive samplers

EN ISO 23875:2022 采矿.操作室的空气质量控制系统.性能要求和试验方法

This document specifies performance and design requirements for air quality control systems for operator enclosures and their monitoring devices. The design specifications are universal in their application and do not contemplate specific mining environments. They are intended to meet identified parameters of both pressurization and respirable particulate and carbon dioxide concentrations. This document also specifies test methods to assess such parameters and provides operational and maintenance instructions. Recommendations are made for operational integration of the air quality control system. Gases and vapours that can be a hazard in the work environment outside of the operator enclosure are excluded from this document.

Mining - Air quality control systems for operator enclosures - Performance requirements and test methods (ISO 23875:2021)

JIS K 0804:2022 气体检测管测量系统

Gas detector tube measurement system

T/GIEHA 035-2022 医院室内空气质量要求

一般要求 医院室内空气应无毒、无害、无异常嗅味。 医院室内空气中不得检出致病菌、病毒等微生物。 分类要求 I类环境空气质量应符合GB 50333等标准的要求。 II类、III类环境空气质量除应满足GB/T 18883等标准的要求（除甲醛以外），还应满足表1的要求。 IV类环境空气质量应符合附录A的要求。 Ⅴ类环境空气质量应符合GB 37488等标准的要求。 有负压要求的房间，除满足相对应类别的空气质量要求外，还应符合附录B的要求。 表1　II类、III类环境医院室内环境空气质量要求 序号　项目　平均时间　指标　单位 　　　II类　III类　 1　新风量　-　30　m3/(h*人) 2　温度　日平均值　符合GB 51039的要求　℃ 3　相对湿度　日平均值　　% 4　菌落总数　空气　依据仪器定　4 (15min)　4 (5min)　CFU/皿 　　物表　　5　10　CFU/cm2 5　二氧化硫SO2　1小时平均值　0.40　0.5　mg/m3 6　二氧化氮NO2　1小时平均值　0.16　0.24　mg/m3 7　一氧化碳CO　日平均值　4　10　mg/m3 8　苯C6H6　1小时平均值　0.01　0.02　mg/m3 9　可吸入颗粒物PM10　日平均值　45　75　ug/m3 10　可吸入颗粒物PM2.5　日平均值　15　25　ug/m3 11　氡222Rn　年平均值 （行动水平）　100　200　Bq/m3 新风量≧分级指标，其他参数要求≦分级指标。 6　检测方法 采样要求 菌落总数的布点方式、采样时间和频次、采样方法等按照GB 15982-2012附录A的规定执行，其他项目按照GB/T 18883和GB/T 18204.6的规定执行。 检测方法 I类环境空气质量检测方法参照GB 50333等标准的相关要求进行。 II类、III类环境空气质量检测方法参照表2进行。 IV类环境空气质量检测方法参照DB11 409-2007等标准的相关要求进行。 Ⅴ类环境空气质量检测方法参照GB 37488等标准的相关要求进行。 表2　室内空气质量项目检测方法 序号　项目　检测方法　来源 1　新风量　（1）示踪气体法 （2）风量罩法等　GB/T 18204 2　温度、相对湿度　热环境参数的检验方法　GB/T 18883 3　菌落总数　按照GB 15982规定的方法进行　GB 15982 4　二氧化硫SO2　甲醛溶液吸收 盐酸副玫瑰苯胺分光光度法　GB/T 16128 GB/T 15262 5　二氧化氮NO2　改进的Saltzaman法　GB 12372 GB/T 15435 6　一氧化碳CO　（1）不分光红外线气体分析法 （2）气相色谱法 （3）容量滴定法　GB/T 18204.23 7　苯C6H6　气相色谱法　（1）GB/T 18883 附录C （2）GB 11737 8　可吸入颗粒物 PM10　撞击式 称重法　GB/T 17095 9　可吸入颗粒物 PM2.5　检测方法按照HJ 618规定的方法进行　HJ 618 10　氡222Rn　(1)空气中氡浓度的闪烁瓶测量方法 (2)径迹蚀刻法 (3)双滤膜法 (4)活性炭盒法　（1）GB/T 14582 （2）GB/T 16147 （3）GB/T 14582 （4）GB/T 14582

Hospital indoor air quality requirements

ASTM D6494-22 工作场所大气中沥青烟颗粒物苯可溶部分测定的标准试验方法

1.1 This test method covers the determination of asphalt fume particulate matter (as benzene soluble fraction) and total particulate matter weight in workplace atmospheres using a polytetrafluoroethylene (PTFE) filter methodology. 1.2 This procedure has been adapted from NIOSH Method 5023 (withdrawn prior to 4th edition (1994) and replaced in 1998 with NIOSH Method 5042) and OSHA Method 58. This adaptation was made to reduce the level of background contamination providing better reproducibility. 1.3 This procedure is compatible with high flow rate personal sampling equipment–0.5 to 2.0 L/min. It can be used for personal or area monitoring. 1.4 The sampling method develops a time-weighted average (TWA) sample and can be used to determine short-term exposure limit (STEL). 1.5 The applicable concentration range for the TWA sample is from 0.2 to 2.0 mg/m3 . NOTE 1—A study has suggested candidate solvents for benzene replacement.2 A less toxic solvent for this analysis would be more appropriate, although the substitution with a solvent other than benzene needs further validations with field data. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For more specific precautionary statements, see Section 9. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Asphalt Fume Particulate Matter in Workplace Atmospheres as Benzene Soluble Fraction

ASTM D4600-22 工作场所大气中苯可溶颗粒物测定的标准试验方法

1.1 This test method describes the sampling and gravimetric determination of benzene-soluble particulate matter that has become airborne as a result of certain industrial processes. This test method can be used to determine the total weight of benzene-soluble materials and to provide a sample that may be used for specific and detailed analyses of the soluble components. 1.2 The limit of detection is 0.05 mg/m3 by sampling a 1 m3 volume of air. NOTE 1—Other volatile organic solvents have been used for this determination and whereas a less toxic solvent for this analysis might be desirable, the substitution of a solvent other than benzene is unwise at this time. A tremendous volume of environmental sampling data based on benzene-soluble determinations has been accumulated over many years in several industries.2 Some of the determinations have been used in epidemiological studies. Furthermore, the use of benzene is specified in existing United States federal standards.3 As a result, it appears imprudent to use a different solvent until the qualitative and quantitative relationship of analyses derived from benzene and a substitute solvent is established. With proper care, benzene can be safely used in the laboratory. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Benzene-Soluble Particulate Matter in Workplace Atmospheres

T/SCIAC 001-2021 尘埃粒子计数器

本文件规定了尘埃粒子计数器的环境条件、要求、试验方法、检验规则和标志、包装、运输、贮存。

Dust Particle Counter