13.040.40 固定源排放限值 标准查询与下载
共找到 1182 条与 固定源排放限值 相关的标准，共 79 页
1 Scope This document specifies the requirements for the installation and on-going quality assurance and quality control of data acquisition and handling systems (DAHS). This includes requirements on: — installation (Clause 5); — quality assurance and quality control during QAL2 (Clause 6); — quality assurance and quality control during on-going operation (Clause 7); — annual functional test (Clause 8); — documentation (Clause 9). This document supports the requirements of EN 14181 and legislation such as the IED [1], MCPD [2] and E-PRTR [3]. It does not preclude the use of additional features and functions provided the minimum requirements of this document are met and that these features do not adversely affect data quality, clarity or access.
Stationary source emissions. Data acquisition and handling systems - Specification of requirements for the installation and on-going quality assurance and quality control of data acquisition and handling systems
- ICS
- 13.040.40
- CCS
- 发布
- 2023-05-31
- 实施
- 2023-05-31
This document specifies the following requirements: a) requirements for measurement sections and sites with respect to performing emission measurements; b) requirements for the measurement objective, plan and report of emission measurements of air pollutants and reference quantities to be carried out in waste gas ducts at industrial plants. This document applies to periodic measurements using manual or automated reference methods (RM). This document specifies generic principles which can be applied to perform emission measurements at different plant types and to meet different measurement objectives. NOTE The measurement objective is specified by the customer. The testing institute identifies the measurement objective and related regulatory requirements at the beginning of the measurement planning. Where measurements are being made for regulatory purposes, the customer should seek approval from the competent authority. This document specifies procedures for taking representative samples in waste gas ducts. This document specifies a procedure for finding the best available sampling point for automated measuring systems used for continuous monitoring of emissions. The planning and reporting aspects of this document are applicable to emission measurements at diffusive and fugitive emission sources. This document does not address aspects of structural safety of chimneys and ducts, construction of working platforms and safety of personnel using them.
Air quality — Measurement of stationary source emissions — Requirements for measurement sections and sites and for the measurement objective, plan and report
- ICS
- 13.040.40
- CCS
- 发布
- 2023-05-17
- 实施
Stationary source emissions - Determination of the mass concentration of sulfur dioxide in flue gases - Performance characteristics of automated measuring systems
- ICS
- 13.040.40
- CCS
- 发布
- 2023-05
- 实施
Stationary source emissions — Sampling and determination of mercury in flue gas using chemical absorption method
- ICS
- 13.040.40
- CCS
- 发布
- 2023-05
- 实施
Stationary source emissions — Determination of mass concentration of particulate matter (dust) at low concentrations — Manual gravimetric method
- ICS
- 13.040.40
- CCS
- 发布
- 2023-05
- 实施
Air quality — Measurement of stationary source emissions — Requirements for measurement sections and sites and for the measurement objective, plan and report
- ICS
- 13.040.40
- CCS
- 发布
- 2023-05
- 实施
Emission Standards of Air Pollutants for Printing Industry
- ICS
- 13.040.40
- CCS
- Z60
- 发布
- 2023-04-24
- 实施
- 2024-01-01
Air Pollutant Emission Standards for Automobile Manufacturing Industry
- ICS
- 13.040.40
- CCS
- Z60
- 发布
- 2023-04-24
- 实施
- 2024-01-01
Technical Specifications for Laboratory Exhaust Gas Pollution Control
- ICS
- 13.040.40
- CCS
- Z 05
- 发布
- 2023-03-23
- 实施
- 2023-04-23
1 Scope This document specifies procedures for establishing quality assurance levels (QAL) for automated measuring systems ( AMS ) installed on industrial plants for the determination of the flue gas components and other flue gas parameters. This document specifies: — a procedure (QAL2) to calibrate the AMS and determine the variability of the measured values obtained by it, so as to demonstrate the suitability of the AMS for its application, following its installation; — a procedure (QAL3) to maintain and demonstrate the required quality of the measurement results during the normal operation of an AMS , by checking that the zero and span characteristics are consistent with those determined during QAL1; — a procedure for the annual surveillance tests (AST) of the AMS in order to evaluate (i) that it functions correctly and its performance remains valid and (ii) that its calibration function and variability remain as previously determined. This document is designed to be used after the AMS has been certified in accordance with the series of documents EN 15267.
Stationary source emissions. Quality assurance of automated measuring systems
- ICS
- 13.040.40
- CCS
- 发布
- 2023-02-28
- 实施
- 2023-02-28
Stationary source emissions — Quality assurance of automated measuring systems
- ICS
- 13.040.40
- CCS
- 发布
- 2023-02-10
- 实施
- 2023-02
Emission Standards of Air Pollutants for Brick and Tile Industry
- ICS
- 13.040.40
- CCS
- Z 60
- 发布
- 2023-02-03
- 实施
- 2023-05-01
本标准规定了玻璃工业废气治理工程的污染物与污染负荷、总体要求、工艺设计、主要工艺设备和材料、检测及过程控制、主要辅助工程、劳动安全与职业卫生、施工与验收、运行与维护等技术要求。 本标准适用于平板玻璃制造的废气治理工程，可作为工程咨询、环境保护设施设计与施工、建设项目竣工环境保护验收及建成后运行管理的参考依据。 玻璃制品制造、玻璃纤维及制品制造、其他玻璃制造的废气治理工程可参考本标准执行。
Technical specifications for waste-gas treatment fromglass industry
- ICS
- 13.040.40
- CCS
- Z25
- 发布
- 2023-02-01
- 实施
- 2023-05-01
BS ISO 7935. Stationary source emissions. Determination of the mass concentration of sulfur dioxide in flue gases. Performance characteristics of automated measuring systems
- ICS
- 13.040.40
- CCS
- 发布
- 2023-01-25
- 实施
- 2023-01-25
Air Pollutant Emission Standards for Thermal Power Plants
- ICS
- 13.040.40
- CCS
- Z 60
- 发布
- 2023-01-05
- 实施
- 2023-03-01
Air Pollutant Emission Standards for Furniture Manufacturing Industry
- ICS
- 13.040.40
- CCS
- Z 60
- 发布
- 2023-01-05
- 实施
- 2023-03-01
Stationary source emissions — Determination of mass concentration of particulate matter (dust) at low concentrations — Manual gravimetric method
- ICS
- 13.040.40
- CCS
- 发布
- 2022-12-30
- 实施
Stationary source emissions — Determination of PM10/PM2.5 mass concentration in flue gas — Measurement at low concentrations by use of impactors
- ICS
- 13.040.40
- CCS
- 发布
- 2022-12-30
- 实施
Stationary source emissions — Determination of mass concentration of particulate matter (dust) at low concentrations — Manual gravimetric method
- ICS
- 13.040.40
- CCS
- 发布
- 2022-12-30
- 实施
Emission Standards of Air Pollutants for Chemical Fiber Industry
- ICS
- 13.040.40
- CCS
- Z60
- 发布
- 2022-12-30
- 实施
- 2023-01-30
