13.060.30 污水 标准查询与下载

JB/T 14104-2020 异形沉淀池刮泥机

Special-shaped sedimentation tank mud scraper

JB/T 14105-2020 永磁电机潜水搅拌机

Permanent magnet motor submersible mixer

JB/T 14087-2020 穿层式中心传动刮泥机

Through-layer center drive mud scraper

JB/T 14103-2020 一体化生活污水处理设备

Integrated domestic sewage treatment equipment

JB/T 14095-2020 农村生活污水净化装置

Rural domestic sewage purification device

JB/T 14084-2020 板框式旋转滤网除污机

Plate and frame rotary filter decontamination machine

JB/T 14094-2020 螺旋式砂水分离器

Spiral sand water separator

JB/T 6932-2020 生物接触氧化法 生活污水净化器

Biological contact oxidation domestic sewage purifier

JB/T 14097-2020 上流式多相芬顿塔

Upflow multiphase Fenton tower

ASTM D3753-20 玻璃纤维（玻璃纤维增强热固性树脂）检修孔和湿井的标准规范

1.1 This specification covers “fiberglass” (glass fiberreinforced thermosetting-resin) manholes and wetwells fabricated with polyester, vinyl ester, or epoxy resin for use primarily in sanitary, storm, and industrial sewer applications. 1.2 The values given in inch-pound units are to be regarded as the standard. The values in parentheses are provided for information purposes only. 1.3 The following precautionary caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—There is no known ISO equivalent to this standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Manholes and Wetwells

BS ISO 5667-10:2020 水质. 采样. 废水采样导则

Water quality. Sampling. Guidance on sampling of waste water

T/DLEPI 003-2020 日用废塑料容器清洗废水治理工程技术规范

本文件规定了日用废塑料容器（PET矿泉水瓶、PET饮料瓶、PET食用油瓶）回收利用加工工艺过程产生的清洗废水治理工程设计、施工、验收、运行与维护的技术要求。

Technical specification for cleaning waste water treatment engineering of household waste plastic containers

DS/ISO 5667-10:2020 水质“取样”第10部分：废水取样指南

Water quality – Sampling – Part 10: Guidance on sampling of waste water

ASTM D4198-20 评价细菌分析和生长用薄膜过滤器的吸水垫的标准试验方法

1.1 These test methods cover the determination of the nutrient-holding capacity and the toxic or nutritive effect on bacterial growth of organisms retained on a membrane filter, when the absorbent pad being tested is used as a nutrient reservoir and medium supply source for the retained bacteria. 1.2 The tests described are conducted on 47 mm diameter disks, although other size disks may be employed for bacterial culture techniques. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Evaluating Absorbent Pads Used with Membrane Filters for Bacteriological Analysis and Growth 

ISO 5667-10:2020 水质. 采样. 第10部分: 废水采样导则

This document contains details on the sampling of domestic and industrial waste water, i.e. the design of sampling programmes and techniques for the collection of samples. It covers waste water in all its forms, i.e. industrial waste water, radioactive waste water, cooling water, raw and treated domestic waste water. It deals with various sampling techniques used and the rules to be applied so as to ensure the samples are representative. Sampling of accidental spillages is not included, although the methods described in certain cases may also be applicable to spillages.

Water quality - Sampling - Part 10: Guidance on sampling of waste water

DB45/T 2164-2020 乡镇卫生院污水处理设施建设技术规范

Technical specifications for the construction of sewage treatment facilities in township health centers

T/SCSX 0101-2020 水处理剂 复合型除磷剂

本标准规定了《水处理剂 复合型除磷剂》的产品分类、技术要求、试验方法、检验规则以及包装、标志、运输、贮存等。 本标准适用于以铝、铁化合物为主要原料，经聚合熟化工艺制成的《水处理剂 复合型除磷剂》，主要用于工业废水、生活污水的除磷处理。

Water treatment agent composite phosphorus removal agent

T/SCSX 0102-2020 水处理剂 复合碳源

本标准规定了《水处理剂  复合碳源》的产品分类、技术要求、试验方法、检验规则以及包装、标志、运输、贮存等。 本标准适用于以醇类、糖类，有机酸及其盐类为主要原料生产的《水处理剂  复合碳源》，该产品主要用于工业废水、生活污水处理系统补充碳源。

Water treatment agent composite carbon source

ASTM C478/C478M-20 圆形预制钢筋混凝土人孔部分的标准规范

Standard Specification for Circular Precast Reinforced Concrete Manhole Sections

ASTM C1814/C1814M-20 雨水过滤元件液压特性测量标准试验方法

1.1 This test standard shall be used to determine the hydraulic characteristics of stormwater filtration elements. 1.2 Elements tested shall be of a size commonly manufactured, not a scale model. 1.3 The position and orientation of all filter elements during testing shall be identical to the position and orientation used during normal operation. 1.4 The direction of flow during testing shall be identical to the direction of flow during normal operation. 1.5 As each stormwater treatment device is unique in design and hydraulic capacity, a sufficient number of accurately measured data points are needed to properly define the hydraulic characteristics of each test element. Therefore, it is imperative that the element setup and subsequent testing methodologies be well defined and executed to assure accurate flow and elevation data. 1.6 This test determines the hydraulic capacity of stormwater filtration systems. Test results are not an indicator of the filtration performance with respect to the capture of solids or other materials. 1.7 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measurement of Hydraulic Characteristics of Stormwater Filtration Elements