13.220.40 材料和制品的可燃性和燃烧性能 标准查询与下载

EN IEC 60332-3-10:2018/AC:2018-11 着火条件下的电缆和光缆试验 第 3-10 部分：垂直安装的成束电线或电缆的垂直火焰蔓延试验 设备

NEW! IEC 60332-3-10:2018 is available as IEC 60332-3-10:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60332-3-10:2018 details the apparatus and its arrangement and calibration for methods of test for the assessment of vertical flame spread of vertically mounted bunched wires or cables, electrical or optical, under defined conditions. This second edition cancels and replaces the first edition published in 2000 and Amendment 1:2008. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) adjustments have been made to the title, and elsewhere, to emphasise the standard is applicable to optical fibre cables as well as metallic conductor types; b) details of the way in which cables are mounted on the ladder have been better defined in order to improve repeatability and reproducibility; c) the connection of the venturi mixer to the burner is better defined. It has the status of a group safety publication in accordance with IEC Guide 104.

Tests on electric and optical fibre cables under fire conditions - Part 3-10: Test for vertical flame spread of vertically-mounted bunched wires or cables - Apparatus

ASTM D5425-18 电工产品火灾危险性评估标准制定的标准指南

1.1 This guide provides guidance on the development of fire hazard assessment standards for electrotechnical products. For the purposes of this guide, products include materials, components, and end-use products. 1.2 This guide is directed toward development of standards that will provide procedures for assessing fire hazards harmful to people, animals, or property. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This fire standard cannot be used to provide quantitative measures. 1.5 This standard is used to predict or provide a quantitative measure of the fire hazard from a specified set of fire conditions involving specific materials, products, or assemblies. This assessment does not necessarily predict the hazard of actual fires which involve conditions other than those assumed in the analysis. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Development of Fire Hazard Assessment Standards of Electrotechnical Products

ASTM D5424-18 垂直电缆槽结构中燃烧时电缆或光缆中绝缘材料烟雾遮蔽的标准试验方法

1.1 This is a fire-test-response standard. 1.2 This test method provides a means to measure the smoke obscuration resulting from burning electrical insulating materials contained in electrical or optical fiber cables when the cable specimens, excluding accessories, are subjected to a specified flaming ignition source and burn freely under well ventilated conditions. 1.3 This test method provides two different protocols for exposing the materials, when made into cable specimens, to an ignition source (approximately 20 kW), for a 20 min test duration. Use it to determine the flame propagation and smoke release characteristics of the materials contained in single and multiconductor electrical or optical fiber cables designed for use in cable trays. 1.4 This test method does not provide information on the fire performance of electrical or optical fiber cables in fire conditions other than the ones specifically used in this test method, nor does it measure the contribution of the cables to a developing fire condition. 1.5 Data describing the burning behavior from ignition to the end of the test are obtained. 1.6 The production of light obscuring smoke is measured. 1.7 The burning behavior is documented visually, by photographic or video recordings, or both. 1.8 The test equipment is suitable for making other, optional, measurements, including the rate of heat release of the burning specimen, by an oxygen consumption technique and weight loss. 1.9 Another set of optional measurements are the concentrations of certain toxic gas species in the combustion gases. 1.10 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. (See IEEE/ASTM SI 10.) 1.11 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.12 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.13 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.14 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Smoke Obscuration of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration

ASTM D3874-18 用热线源点燃材料的标准试验方法

Standard Test Method for Ignition of Materials by Hot Wire Sources

ASTM D5537-18 垂直电缆槽结构中燃烧时电缆或光缆中绝缘材料的热释放、火焰蔓延、烟雾遮蔽和质量损失试验的标准试验方法

1.1 This is a fire-test-response standard. 1.2 This test method provides a means to measure the heat released and smoke obscuration by burning the electrical insulating materials contained in electrical or optical fiber cables when the cable specimens, excluding accessories, are subjected to a specified flaming ignition source and burn freely under well ventilated conditions. Flame propagation cable damage, by char length, and mass loss are also measured. 1.3 This test method provides two different protocols for exposing the materials, when made into cable specimens, to an ignition source (approximately 20 kW), for a 20 min test duration. Use it to determine the heat release, smoke release, flame propagation and mass loss characteristics of the materials contained in single and multiconductor electrical or optical fiber cables. 1.4 This test method does not provide information on the fire performance of materials insulating electrical or optical fiber cables in fire conditions other than the ones specifically used in this test method nor does it measure the contribution of the materials in those cables to a developing fire condition. 1.5 Data describing the burning behavior from ignition to the end of the test are obtained. 1.6 This test equipment is suitable for measuring the concentrations of certain toxic gas species in the combustion gases (see Appendix X4). 1.7 The values stated in SI units are to be regarded as standard (see IEEE/ASTM SI-10). The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.8 This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions 1.9 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Heat Release, Flame Spread, Smoke Obscuration, and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable T

ASTM D6194-18 材料的辉光丝点火的标准试验方法

1.1 This test method covers the minimum temperature required to ignite insulating materials using a glowing heat source. In a preliminary fashion, this test method differentiates between the susceptibilities of different materials with respect to their resistance to ignition due to an electrically-heated source. 1.2 This test method applies to molded or sheet materials available in thicknesses ranging from 0.25 to 6.4 mm. 1.3 This test method is not valid for determining the ignition behavior of complete electrotechnical equipment, since the design of the electrotechnical product influences the heat transfer between adjacent parts. 1.4 This test method measures and describes the response or materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. (See IEEE/ASTM SI-10 for further details.)For specific precautionary statements, see Section 9. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 9. 1.7 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. NOTE 1—Although this test method and IEC 60695-2-13 differ in approach and in detail, data obtained using either are technically equivalent. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Glow-Wire Ignition of Materials

ASTM D5048-18 用125mm火焰测量固体塑料的比较燃烧特性和耐烧穿性的标准试验方法

Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using a 125-mm Flame

IEC 60332-3-24:2018 RLV 着火条件下电缆和光缆的试验第3-24部分:垂直安装的成束电线或电缆的垂直火焰蔓延试验C类

Tests on electric and optical fibre cables under fire conditions - Part 3-24: Test for vertical flame spread of vertically-mounted bunched wires or cables - Category C

IEC 60332-3-22:2018 RLV 着火条件下电缆的试验第3-22部分:垂直安装的成束电线或电缆的垂直火焰蔓延试验A类

Tests on electric cables under fire conditions - Part 3-22: Test for vertical flame spread of vertically-mounted bunched wires or cables - Category A

IEC 60332-3-21:2018 着火条件下电缆和光缆的试验第3-21部分:垂直安装的成束电线或电缆的垂直火焰蔓延试验A类F/R

Tests on electric and optical fibre cables under fire conditions - Part 3-21: Test for vertical flame spread of vertically-mounted bunched wires or cables - Category A F/R

IEC 60332-3-22:2018 着火条件下电缆的试验第3-22部分:垂直安装的成束电线或电缆的垂直火焰蔓延试验A类

Tests on electric cables under fire conditions - Part 3-22: Test for vertical flame spread of vertically-mounted bunched wires or cables - Category A

IEC 60332-3-23:2018 RLV 着火条件下电缆和光缆的试验第3-23部分:垂直安装的成束电线或电缆的垂直火焰蔓延试验B类

Tests on electric and optical fibre cables under fire conditions - Part 3-23: Test for vertical flame spread of vertically-mounted bunched wires or cables - Category B

IEC 60332-3-25:2018 RLV 着火条件下电缆和光缆的试验第3-25部分:垂直安装的成束电线或电缆的垂直火焰蔓延试验D类

Tests on electric and optical fibre cables under fire conditions - Part 3-25: Test for vertical flame spread of vertically-mounted bunched wires or cables - Category D

IEC 60332-3-10:2018 RLV 着火条件下电缆和光缆的试验第3-10部分:垂直安装的成束电线或电缆的垂直火焰蔓延试验仪器

Tests on electric and optical fibre cables under fire conditions - Part 3-10: Test for vertical flame spread of vertically-mounted bunched wires or cables - Apparatus

IEC 60332-3-21:2018 RLV 着火条件下电缆和光缆的试验第3-21部分:垂直安装的成束电线或电缆的垂直火焰蔓延试验A类F/R

Tests on electric and optical fibre cables under fire conditions - Part 3-21: Test for vertical flame spread of vertically-mounted bunched wires or cables - Category A F/R

IEC 60332-3-23:2018 着火条件下电缆和光缆的试验第3-21部分:垂直安装的成束电线或电缆的垂直火焰蔓延试验A类F/R

Tests on electric and optical fibre cables under fire conditions - Part 3-21: Test for vertical flame spread of vertically-mounted bunched wires or cables - Category A F/R

ASTM D8211-18 平坦表面上气体热表面着火温度的标准试验方法

Standard Test Method for Hot Surface Ignition Temperature of Gases on Flat Surface

DIN EN 17077:2018 粉尘层燃烧行为的测定；德文版 EN 17077:2018

Safety assessments need to look at the possibility of a fire in dust layers which could then propagate or initiate an explosion. The so-called burning class of a dust gives an indication of dust layer combustion behaviour. The burning class can be determined by a simple screening test. It is aimed to develop a European standard describing the methodology for the determination and classification of dust layer combustion behaviour.The standard should describe whether a fire started in a dust layer using an external ignition source can propagate, and if so to what extent . Based on the test result the combustion behaviour is classified according to the following:Type of Reaction Class No ignition 1 Brief ignition, rapid extinction 2 Localised combustion, negligible spreading 3 Smouldering or slow combustion without flame 4 Slow, quiet burning with flames 5 Very rapid combustion with flame propagation or rapid decomposition without flame 6 The standard will cover: - Details of the test set-up; - Description of test performance; - Classification procedure; - Effect of process conditions (e. g. process temperature).

Determination of burning behaviour of dust layers; German version EN 17077:2018

ASTM D4391-18a 与纺织品燃烧性能有关的标准术语

Standard Terminology Relating to The Burning Behavior of Textiles

IEC 60332-3-24:2018 着火条件下电缆和光缆的试验第3-24部分:垂直安装的成束电线或电缆的垂直火焰蔓延试验C类

"This part of IEC 60332 covers category C for methods of test for the assessment of vertical flame spread of vertically mounted bunched wires or cables@ electrical or optical@ under defined conditions. This document relates to cables installed on the test ladder to achieve a nominal total volume of non-metallic material of 1@5 l/m of test sample. The flame application time is 20 min. The method of mounting uses the front of the standard ladder. The category is intended for general use where low volumes of non-metallic material are required to be evaluated. The test is intended for type approval testing. The requirements for the selection of cables for testing are given in Annex A. The flame spread is measured as the extent of damage of the cable sample. This procedure can be used to demonstrate the cable??s ability to limit flame spread. A recommended performance requirement is given in Annex B. NOTE For the purposes of this document the term ""electric wire or cable"" covers all insulated metallic conductor cables used for the conveyance of energy or signals."

Tests on electric and optical fibre cables under fire conditions - Part 3-24: Test for vertical flame spread of vertically-mounted bunched wires or cables - Category C