13.220.40 材料和制品的可燃性和燃烧性能 标准查询与下载

IEC 60332-3-24:2018 着火条件下电缆和光缆的试验第3-24部分:垂直安装的成束电线或电缆的垂直火焰蔓延试验C类

"This part of IEC 60332 covers category C for methods of test for the assessment of vertical flame spread of vertically mounted bunched wires or cables@ electrical or optical@ under defined conditions. This document relates to cables installed on the test ladder to achieve a nominal total volume of non-metallic material of 1@5 l/m of test sample. The flame application time is 20 min. The method of mounting uses the front of the standard ladder. The category is intended for general use where low volumes of non-metallic material are required to be evaluated. The test is intended for type approval testing. The requirements for the selection of cables for testing are given in Annex A. The flame spread is measured as the extent of damage of the cable sample. This procedure can be used to demonstrate the cable??s ability to limit flame spread. A recommended performance requirement is given in Annex B. NOTE For the purposes of this document the term ""electric wire or cable"" covers all insulated metallic conductor cables used for the conveyance of energy or signals."

Tests on electric and optical fibre cables under fire conditions - Part 3-24: Test for vertical flame spread of vertically-mounted bunched wires or cables - Category C

BS EN 17077:2018 粉尘层燃烧行为的测定

What is BS EN 17077 - Burning behaviour of dust layers about?   BS EN 17077 is a European Standard on explosion and fire precautions in industrial and   chemical plants, that specifies a method for experimental determination of the burning behaviour of dust layers.   BS EN 17077 describes a test method for the determination of the burning behaviour of dust layers under defined initial conditions of airflow, temperature, and ignition. The main objective of BS EN 17077 is to establish efficient explosion and fire precautions in industrial and chemical plants and facilities  

Determination of burning behaviour of dust layers

ISO/TS 19021:2018 使用傅里叶变换红外光谱法测定ISO5659-2中气体浓度的试验方法

Test method for determination of gas concentrations in ISO 5659-2 using Fourier transform infrared spectroscopy

ASTM D4986-18 泡沫聚合材料水平燃烧特性的标准试验方法

1.1 This fire-test-response standard contains a test method for small-scale laboratory procedures to be used to determine the relative rate of burning and the extent and time of burning of horizontally oriented cellular polymeric materials having a density less than 250 kg/m3 . 1.2 The results are intended to serve as a preliminary indication of their acceptability with respect to flammability for a particular application. The final acceptance of the material is dependent upon its use in the end-product that conforms with the standards applicable to such end-product. 1.3 The classification system described in the Appendix X1 is intended for quality assurance and the preselection of component materials for products. 1.4 This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.5 The values stated in SI units are to be regarded as standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see 6.1.1. 1.7 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. NOTE 1—This test method is equivalent to ISO 9772. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Horizontal Burning Characteristics of Cellular Polymeric Materials

ASTM D4391-18 与纺织品燃烧性能有关的标准术语

Standard Terminology Relating to The Burning Behavior of Textiles

IEC 60331-3:2018 RLV 着火条件下电缆的试验.电路完整性.第3部分:在金属外壳中试验的额定电压0.6/1.0 kV及以下电缆在至少830°C温度下冲击着火的试验方法

Tests for electric cables under fire conditions - Circuit integrity - Part 3: Test method for fire with shock at a temperature of at least 830°C for cables of rated voltage up to and including 0,6/1,0

IEC 60331-1:2018 RLV 着火条件下电缆的试验.电路完整性.第1部分:额定电压0.6/1.0 kV及以下 总直径超过20 mm的电缆在至少830°C温度下冲击着火的试验方法

Tests for electric cables under fire conditions - Circuit integrity - Part 1: Test method for fire with shock at a temperature of at least 830°C for cables of rated voltage up to and including 0,6/1,0

IEC 60331-2:2018 RLV 着火条件下电缆的试验.电路完整性.第2部分:额定电压0.6/1.0 kV及以下 总直径不超过20 mm的电缆在至少830°C温度下冲击着火的试验方法

Tests for electric cables under fire conditions - Circuit integrity - Part 2: Test method for fire with shock at a temperature of at least 830°C for cables of rated voltage up to and including 0,6/1,0

IEC 60331-3:2018 着火条件下电缆的试验.电路完整性.第3部分:在金属外壳中试验的额定电压0.6/1.0 kV及以下电缆在至少830°C温度下冲击着火的试验方法

Tests for electric cables under fire conditions - Circuit integrity - Part 3: Test method for fire with shock at a temperature of at least 830°C for cables of rated voltage up to and including 0,6/1,0

IEC 60754-3:2018 电缆材料燃烧过程中产生的气体试验 - 第3部分:离子色谱法测量低含量卤素含量

Test on gases evolved during combustion of materials from cables - Part 3: Measurement of low level of halogen content by ion chromatography

ASTM E2688-18 标准样品制备和安装用于评估表面燃烧特性的标准实施规程

1.1 This practice describes a procedure for specimen preparation and mounting when testing tapes to assess flame spread and smoke development as surface burning characteristics using Test Method E84. Tapes are to be tested in full coverage as applied to fiber cement board as described in Test Method E84. 1.2 This practice applies to tapes intended for various uses within buildings. The tapes addressed in this practice are not able to be supported by their own structural characteristics during the test. 1.3 Testing is conducted in accordance with Test Method E84. 1.4 This practice does not provide pass/fail criteria that can be used as a regulatory tool. 1.5 This practice does not apply to materials for which the test specimen does not remain in place before and during the test until maximum flame propagation has occurred. 1.6 This practice is not for system evaluation. It is for the comparison of the materials only. 1.7 Use the values stated in inch-pound units as the standard, in referee decisions. The values in the SI system of units are given in parentheses, for information only; see IEEE/ASTM SI-10 for further details. 1.8 This fire standard cannot be used to provide quantitative measures. 1.9 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.10 This standard gives instructions on specimen preparation and mounting, but the fire-test-response method is given in Test Method E84. See also Section 9. 1.11 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes shall not be considered requirements of the standard. 1.12 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.13 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Specimen Preparation and Mounting of Tapes to Assess Surface Burning Characteristics

ASTM D4151-18 易燃性的标准试验方法

1.1 This test method provides a means to identify blanket fabrics which ignite easily and propagate flame across the surface. 1.2 This test method specifies the procedures described in the “Voluntary Blanket Flammability Standard” which has been used by the blanket industry in the United States since 1972. 1.3 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions. NOTE 1—This test method is not identical to 16 CFR Part 1610, Flammability of Clothing Textiles. Consumer Product Safety Commission regulations require that fabrics introduced into commerce meet the requirements of 16 CFR Part 1610. 1.4 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Flammability of Blankets

ASTM D6545-18 用于儿童的纺织品的可燃性的标准试验方法

1.1 This test method evaluates the relative flammability of textiles and garments intended for use in children’s sleepwear. The procedures of this test method follow testing and laundering procedures used to evaluate the flammability of children’s sleepwear contained in U.S. Federal Regulations 16 CFR 1615 and 1616. 1.2 A textile used in children’s sleepwear must be tested in its original state and after 50 laundering and drying cycles to assess the flame resistance of the textile relative to its use life. 1.3 This method is identical to the method outlined in the regulations 16 CFR 1615 or 1616. The regulation includes additional information such as sampling plans, record keeping requirements, and interpretations for compliance applicable to children’s sleepwear. Please consult 16 CFR 1615 and 1616 for these operations and interpretations. 1.4 The values stated in SI units are to be regarded as the standard; inch-pound units are provided for information only. 1.5 This test method is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.6 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental health practices and determines the applicability of regulatory limitations prior to use. Specific precautionary information is found in 8.5 and 9.5. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Flammability of Textiles Used in Children's Sleepwear

ASTM F1516-13(2018) 用热熔法密封弹性地板产品接缝的标准实施方法（推荐时）

1.1 This practice covers the instructions and precautions to be observed to ensure satisfactory performance of seams in resilient flooring sealed by the heat weld method. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See precaution information in 6.1. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Sealing Seams of Resilient Flooring Products by the Heat Weld Method (when Recommended)

ASTM D635-18 水平位置的燃烧速率和/或程度和燃烧时间的标准测试方法

1.1 This fire-test-response test method covers a small-scale laboratory screening procedure for comparing the relative linear rate of burning or extent and time of burning, or both, of plastics in the form of bars, molded or cut from sheets, plates, or panels, and tested in the horizontal position. NOTE 1—This test method, and test method A of IEC 60695-11-10 are technically equivalent. NOTE 2—For additional information on materials which do not burn to the first reference mark by this test, see Test Method D3801. 1.2 This test method was developed for polymeric materials used for parts in devices and appliances. The results are intended to serve as a preliminary indication of their acceptability with respect to flammability for a particular application. The final acceptance of the material is dependent upon its use in complete equipment that conforms with the standard applicable to such equipment. 1.3 The classification system described in Appendix X1 is intended for quality assurance and the preselection of component materials for products. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazards or fire risk assessment of materials, products, or assemblies under actual fire conditions. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements, see 9.2. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position

KS C IEC 60695-11-2:2017 火灾危险性试验第11-2部分:试验火焰1kw标称预混火焰装置、验证性试验装置和指南

Fire hazard testing — Part 11-2: Test flames — 1 kW nominal premixed flame — Apparatus, confirmatory test arrangement and guidance

KS C IEC 60695-11-2-2017 火灾危险性试验第11-2部分:试验火焰1kw标称预混火焰装置、验证性试验装置和指南

Fire hazard testing — Part 11-2: Test flames — 1 kW nominal premixed flame — Apparatus, confirmatory test arrangement and guidance

KS C IEC 60695-11-2-2017(2022) 火灾危险试验.第11-2部分:试验火焰.1kW标称预混合火焰.设备、确认试验布置和指南

Fire hazard testing — Part 11-2: Test flames — 1 kW nominal premixed flame — Apparatus, confirmatory test arrangement and guidance

ASTM G86-17 测定环境液体氧和加压液体和气态氧环境中材料对机械冲击的点火灵敏度的标准测试方法

1.1 This test method2 describes test equipment and techniques to determine the impact sensitivity of materials in oxygen under two different conditions: (1) in ambient pressure liquid oxygen (LOX) or (2) under pressure-controlled conditions in LOX or gaseous oxygen (GOX). It is applicable to materials for use in LOX or GOX systems at pressures from ambient to 68.9 MPa (0 to 10 000 psig). The test method described herein addresses testing with pure oxygen environments; however, other oxygen-enriched fluids may be substituted throughout this document. 1.2 This test method provides a means for ranking nonmetallic materials as defined in Guide G63 for use in liquid and gaseous oxygen systems and may not be directly applicable to the determination of the sensitivity of the materials in an end-use configuration. This test method may be used to provide batch-to batch acceptance data. This test method may provide a means for evaluating metallic materials in oxygen-enriched atmospheres also; however, Guide G94 should be consulted for preferred testing methods. 1.3 Values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See also Section 9. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining Ignition Sensitivity of Materials to Mechanical Impact in Ambient Liquid Oxygen and Pressurized Liquid and Gaseous Oxygen Environments

ASTM E1822-17 堆叠椅子防火试验标准试验方法

Standard Test Method for Fire Testing of Stacked Chairs