13.340.10 防护服装 标准查询与下载
共找到 1697 条与 防护服装 相关的标准，共 114 页
Protective clothing. Protection against liquid chemicals. Measurement of repellency, retention, and penetration of liquid pesticide formulations through protective clothing materials
- ICS
- 13.340.10
- CCS
- 发布
- 2021-07-06
- 实施
- 2021-07-06
Surgical drapes, gowns and clean air suits, used as medical devices, for patients, clinical staff and equipment — Test method to determine the resistance to wet bacterial penetration
- ICS
- 13.340.10
- CCS
- 发布
- 2021-07-01
- 实施
Protective clothing for users of hand-held chainsaws —Part 6: Performance requirements and test methods for upper body protectors
- ICS
- 13.340.10
- CCS
- 发布
- 2021-07-01
- 实施
This document specifies the performance requirements, test methods, design requirements, identification and marking information for leg protectors that offer protection against cutting by hand-held chainsaws.
Protective clothing for users of hand-held chainsaws — Part 2: Performance requirements and test methods for leg protectors
- ICS
- 13.340.10
- CCS
- 发布
- 2021-07-01
- 实施
Protective clothing for users of hand-held chainsaws —Part 6: Performance requirements and test methods for upper body protectors
- ICS
- 13.340.10
- CCS
- 发布
- 2021-07-01
- 实施
This document specifies the test rig for assessing the resistance to cutting of protective clothing, footwear and gloves by hand-held chainsaws. It also describes the calibration procedure.
Protective clothing for users of hand-held chainsaws — Part 1: Test rig for testing resistance to cutting by a chainsaw
- ICS
- 13.340.10
- CCS
- 发布
- 2021-07-01
- 实施
This document specifies requirements and test methods for assessing the resistance to cutting of gaiters by hand-held chainsaws and other properties. It includes a requirement and a test method for assessing the strength of underfoot straps of gaiters. This document is applicable to gaiters used in conjunction with safety footwear with a steel toecap conforming to ISO 20345 design "C" or "D". These gaiters are designed to be used only in association with a defined model of footwear and tested together. NOTE These products are intended, but are not limited, to be used in combination with a defined model of orthopaedic footwear. This document does not apply to gaiters intended for use in situations where there is a significant risk of tripping, such as tree climbing or in forests.
Protective clothing for users of hand-held chainsaws — Part 5: Performance requirements and test methods for protective gaiters
- ICS
- 13.340.10
- CCS
- 发布
- 2021-07-01
- 实施
ISO 11999-6:2016 specifies the minimum design and performance requirements for footwear as part of personal protective equipment [PPE] to be used by firefighters, primarily but not solely to protect against flame and high thermal loads while fighting fires occurring in structures.
PPE for firefighters — Test methods and requirements for PPE used by firefighters who are at risk of exposure to high levels of heat and/or flame while fighting fires occurring in structures — Part 6: Footwear
- ICS
- 13.340.10
- CCS
- 发布
- 2021-07-01
- 实施
ISO 18639-3:2018 specifies test methods and minimum performance requirements for protective clothing for firefighters while engaged in rescue activities. Clothing related to specific rescue activities are documented in individual subclauses, see 6.2.1 or 6.2.2. NOTE For further guidance see ISO 18639‑1. Subclauses of this document cover general clothing design, the minimum performance level of the materials used and the methods of test for determining this performance level. ISO 18639-3:2018 does not cover special clothing for use in other high risk situations such as firefighting. ISO 18639-3:2018 does not cover protection for the head, hands and feet or protection against other hazards, e.g. chemical, biological, radiation and electrical hazards, except for limited, accidental exposure to some chemicals and contaminated blood or other body fluids.
PPE ensembles for firefighters undertaking specific rescue activities — Part 3: Clothing
- ICS
- 13.340.10
- CCS
- 发布
- 2021-07-01
- 实施
Clothing and equipment for protection against heat — Test method for convective heat resistance using a hot air circulating oven
- ICS
- 13.340.10
- CCS
- 发布
- 2021-07-01
- 实施
Surgical drapes, gowns and clean air suits, used as medical devices, for patients, clinical staff and equipment — Test method to determine the resistance to wet bacterial penetration
- ICS
- 13.340.10
- CCS
- 发布
- 2021-07-01
- 实施
ISO 13506-1:2017 specifies the overall requirements, equipment and calculation methods to provide results that can be used for evaluating the performance of complete garments or protective clothing ensembles exposed to short duration flame engulfment. This test method establishes a rating system to characterize the thermal protection provided by single-layer and multi-layer garments made of flame resistant materials. Any material construction such as coated, quilted or sandwich can be used. The rating is based on the measurement of heat transfer to a full-size manikin exposed to convective and radiant energy in a laboratory simulation of a fire with controlled heat flux, duration and flame distribution. The heat transfer data are summed over a prescribed time to give the total transferred energy. For the purposes of this test method, the incident heat flux is limited to a nominal level of 84 kW/m2 and limited to exposure durations of 3 s to 12 s dependant on the risk assessment and expectations from the thermal insulating capability of the garment. The results obtained apply only to the particular garments or ensembles, as tested, and for the specified conditions of each test, particularly with respect to the heat flux, duration and flame distribution. This test method requires a visual evaluation, observation and inspection on the overall behaviour of the test specimen during and after the exposure as the garment or complete ensemble on the manikin is recorded before, during and after the flame exposure. Visuals of the garment or complete ensemble on the manikin are recorded (i.e. video and still images) before, during and after the flame exposure. This also applies to the evaluation of protection for the hands or the feet when they do not contain sensors. For the interfaces of ensembles tested, the test method is limited to visual inspection. The effects of body position and movement are not addressed in this test method. The heat flux measurements can also be used to calculate the predicted skin burn injury resulting from the exposure (see ISO 13506-2). This test method does not simulate high radiant exposures such as those found in arc flash exposures, some types of fire exposures where liquid or solid fuels are involved, nor exposure to nuclear explosions. NOTE 1 This test method provides information on material behaviour and a measurement of garment performance on a stationary upright manikin. The relative size of the garment and the manikin and the fit of the garment on the shape of the manikin have an important influence on the performance. NOTE 2 This test method is complex and requires a high degree of technical expertise in both the test setup and operation. NOTE 3 Even minor deviations from the instructions in this test method can lead to significantly different test results.
Protective clothing against heat and flame — Part 1: Test method for complete garments — Measurement of transferred energy using an instrumented manikin
- ICS
- 13.340.10
- CCS
- 发布
- 2021-07-01
- 实施
This document provides a test method for evaluating the physiological impact of protective fabric ensembles and potentially protective clothing ensembles in a series of simulated activities (phases) under defined ambient conditions. This standard test method characterizes the essential properties of fabric assemblies of a representative garment or clothing ensemble for thermo-physiological assessment: — dry thermal insulation; — cooling properties during average metabolic activity and moisture management (dry and wet heat transfer); — drying behaviour. Default measurements are done on fabric samples representing the garment or protective clothing combination. Optionally and in addition to the standard test method, the same testing protocol can be applied to characterise more complex protective clothing ensembles including underwear, air layer and certain design features[1]. In addition, measurements on readymade garments are possible. This test method is intended to be used to measure and describe the behaviour of fabric assemblies of a garment or clothing ensemble in response to a simulated series of activities under controlled laboratory conditions, with the results used to optimize garment combinations and material selection. Furthermore, this document together ISO 18640-2, is intended to be used to describe the thermo-physiological impact of protective clothing but not the risk for heat stress under actual fire conditions. The results of this test can be used as elements of a risk assessment with respect to thermo-physiological load. [1] A study conducted by Empa (Swiss Federal Laboratories for Materials Science and Technology, Switzerland) showed good correlation between results of standard torso tests (without underwear and air layers on fabrics) to tests on fabrics with underwear, tests on fabrics with underwear and air layers and test on readymade garments (with underwear and with or without air layers) of the same material composition. Due to the added thermal insulation values of the additional layers direct comparison of results between different measurement configurations is not possible, however.
Protective clothing for firefighters — Physiological impact — Part 1: Measurement of coupled heat and moisture transfer with the sweating torso
- ICS
- 13.340.10
- CCS
- 发布
- 2021-07-01
- 实施
Protective clothing — Protection against flame —Method of test for limited flame spread
- ICS
- 13.340.10
- CCS
- 发布
- 2021-07-01
- 实施
Protective clothing — Protection against flame —Method of test for limited flame spread
- ICS
- 13.340.10
- CCS
- 发布
- 2021-07-01
- 实施
1.1 This practice covers standardized exposures to laundering, simulated sunlight, and chlorinated pool water to simulate two years of seasonal exposure for apparel textiles labeled as ultraviolet (UV)-protective. 1.2 This practice is used in conjunction with AATCC TM183 and Specification D6603 as they relate to testing and labeling of UV-protective textiles after two years of simulated seasonal use. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Practice for Preparation of Textiles Prior to Ultraviolet (UV) Transmission Testing
- ICS
- 13.340.10
- CCS
- 发布
- 2021-07-01
- 实施
ISO 13506-2:2017 provides technical details for calculating predicted burn injury to human skin when its surface is subject to a varying heat flux, such as may occur due to energy transmitted through and by a garment or protective clothing ensemble exposed to flames. A series of test cases are provided against which the burn injury prediction calculation method is verified. It also contains requirements for the in situ calibration of the thermal energy sensor ? skin injury prediction system for the range of heat fluxes that occur under garments. The skin burn injury calculation methods as presented in this test method do not include terms for handling short wavelength radiation that may penetrate the skin. The latter include arc flashes, some types of fire exposures with liquid or solid fuels, and nuclear sources.
Protective clothing against heat and flame — Part 2: Skin burn injury prediction — Calculation requirements and test cases
- ICS
- 13.340.10
- CCS
- 发布
- 2021-07-01
- 实施
This document specifies the performance requirements, test methods, design requirements, identification and marking information for upper body protectors that offer protection against cutting by hand-held chainsaws. It also specifies procedures for sampling and pre-treatment of upper body protectors, the measurement of the protective coverage, the apparatus and test methods for assessing resistance to cutting, and the practical performance test for evaluating ergonomic properties. Guidance on chainsaw use and the selection of appropriate upper body protectors is given in Annex A.
Protective clothing for users of hand-held chainsaws — Part 6: Performance requirements and test methods for upper body protectors
- ICS
- 13.340.10
- CCS
- 发布
- 2021-07-01
- 实施
ISO 11999-4:2015 specifies minimum design and performance requirements for gloves as part of personal protective equipment (PPE) to be used by firefighters, primarily, but not solely, to protect against exposure to flame and high thermal loads.
PPE for firefighters — Test methods and requirements for PPE used by firefighters who are at risk of exposure to high levels of heat and/or flame while fighting fires occurring in structures — Part 4: Gloves
- ICS
- 13.340.10
- CCS
- 发布
- 2021-07-01
- 实施
Clothing for protection against liquid chemicals —Determination of the resistance of protective clothing materials to penetration by liquids under pressure
- ICS
- 13.340.10
- CCS
- 发布
- 2021-07-01
- 实施
