13.340.60 标准查询与下载

CSA Z259.16-2004(R2014) 主动防坠落系统的设计

1 Scope 1.1 This Standard is intended for professional engineers with expertise in designing fall-protection systems. It specifies requirements for the design and performance of complete active fall-protection systems, including travel-restraint and vertical and horizontal fall-arrest systems. 1.2 This Standard is not intended as a substitute for testing and certification of individual components of fall-protection equipment in accordance with applicable CSA Z259 equipment Standards. 1.3 This Standard does not cover the design of passive fall-protection systems such as guardrails and nets, except where such passive systems are also designed to serve as anchorage and/or anchorage connector subsystems for active fall-protection systems covered by this Standard. 1.4 This Standard does not cover the design of positioning systems. 1.5 This Standard does not cover the determination of structural strength and behaviour of components or anchorages of active fall-protection systems. It does, however, establish the safety criteria once the strengths and behaviours are known. Such strengths and behaviours are determined by analytical testing or engineering methods and by CSA or other design Standards for the materials and structural systems being used. 1.6 This Standard does not specify design or performance requirements for fall-arrest equipment or systems that have been manufactured and successfully tested in accordance with the requirements of another CSA Z259 Standard. 1.7 This Standard does not supersede the requirements of applicable occupational safety and health regulations. Where the requirements in this Standard differ from legislated requirements, the most conservative requirement is followed. 1.8 In CSA Standards, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; and "may" is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Legends to equations and figures are considered requirements.

Design of Active Fall-Protection Systems

ISO 10333-6:2004 个人防跌落系统.第6部分:系统性能试验

This part of ISO 10333 specifies tests and requirements for complete personal fall arrest systems (PFAS) made up from specific combinations of components and subsystems selected from those conforming to the other parts of ISO 10333 and to ISO 14567, where it is both important and desirable to ascertain satisfactory system performance and interactive component compatibility. It includes PFAS performance tests using a rigid torso test mass as a surrogate for the fader. Examples of personal fall arrest systems, as well as descriptions of how components or subsystems may be connected together to constitute a system, are also given. This part of ISO 10333 is applicable to PFAS limited to single-person use of a total mass not exceeding 100 kg and, when activated, will arrest the person and limit the arresting force to a maximum of 6 kN. It is not applicable to a) PFAS which use waist belts or chest harnesses as the sole body holding component, b) PFAS incorporating lanyards without energy absorbers or without a means of energy dissipation, c) subsystems and components outside the PFAS scopes of the other parts of ISO 10333 and ISO 14567, or d) equipment used for material lifting purposes. Where other features are integral with components and subsystems which allow them to be assembled into other types of safety system associated with personal fall arrest systems — for example, work positioning systems (WPS), fall restraint systems (FRS), controlled descent systems (CDS), confined space access systems (CSAS) or rescue systems (RS) — this part of ISO 10333 relates only to the fall arrest function of such components and subsystems. This part of ISO 10333 does not specify those additional requirements that would apply when personal fall arrest Systems are subjected to special conditions of use (where, for example, there exist unusual limitations concerning access to the place of work and/or particular environmental factors). NOTE Personal fall arrest systems outside the scope of this part of ISO 10333 need to be performance tested in the manner in which they are intended to be used, taking into account the workplace geometry. Advice will need to be sought from the equipment manufacturer accordingly.

Personal fall-arrest systems - Part 6: System performance tests

EN 362:2004 预防高空坠落的人身保护设备.连接器

This document specifies the requirements, test methods, marking and information supplied by the manufacturer for connectors. Connectors conforming to this document are used as connecting elements in personal fall protection systems, i.e. fall arrest, work positioning, rope access, restraint and rescue systems.

Personal protective equipment against falls from a height - Connectors

ISO 22846-1:2003 个人防跌落保护性设备.绳索接近系统.第1部分:工作系统的基本原理

This part of ISO 22846 gives the fundamental principles for the use of rope-access methods for work at height. It is intended for use by employers, employees and self-employed persons who use rope-access methods, by those commissioning rope-access work and by rope-access associations. This part of ISO 22846 is applicable to the use of rope-access methods on buildings, other structures (on- or offshore) or natural features (such as cliff faces), during which ropes are suspended from or connected to a structure or natural feature. It is applicable to situations where ropes are used as the primary means of access, egress or support and as the primary means of protection against a fall. This part of ISO 22846 is not intended to apply to the use of rope-access methods for leisure activities, arboriculture, general steeplejack methods or emergency personal-evacuation systems, or to the use of rope-access (line rescue) techniques by the fire brigade and other emergency services for rescue work or for rescue training. Nevertheless, those engaged in other similar activities are likely to benefit from the advice given in this part of ISO 22846, as many of the principles do apply to, and offer good practice for, activities outside this formally defined scope. NOTE This is the first of a planned multi-part series of International Standards for rope access.

Personal equipment for protection against falls - Rope access systems - Part 1: Fundamental principles for a system of work

NF P93-311-2:2003 安全网.第2部分:安全网定位极限的安全要求

Safety nets - Part 2: safety requirements for the positioning limits

NF P93-311-1:2003 安全网.第1部分:安全要求和试验方法

Safety nets - Part 1 : safety requirements, test methods.

DS/EN 360:2002 防止从高处坠落的个人防护设备 伸缩式防坠器

This European Standard specifies the requirements, test methods, marking, information supplied by the manufacturer and packaging for retractable type fall arresters. Retractable type fall arresters conforming to this European Standard are sub-systems constituting one of the fall arrest systems covered in EN 363, when combined with a full body harness specified in EN 361. Other types of fall arresters are specified in EN 353-1 and EN 353-2. Energy absorbers are specified in EN 355.

Personal protective equipment against falls from a height - Retractable type fall arresters

DIN EN 1263-2:2002 安全网络.第2部分:定位范围安全要求; 德文版本 EN 1263-2:2002

This European Standard specifies safety requirements for the positioning of safety nets in accordance with the manufacturer's instruction manual and with the product specifications and for the testing of system S, system T, system U and system V safety nets in accordance with EN 1263-1. Small safety nets of system S according to EN 1263-1 (less than 35 m and 5,0 m on the shortest side) are not dealt with in this European Standard.#,,#

Safety nets - Part 2: Safety requirements for the positioning limits; German version EN 1263-2:2002

DS/EN 1263-2:2002 安全网 第2部分：定位限制的安全要求

This Standard specifies safety requirements for the positioning of safety nets in accordance with the manufacturer's instruction manual and with the product specifications and for testing of system S, system T, system U and system V safety nets in accordance with EN 1263-1.

Safety nets - Part 2: Safety requirements for the positioning limits

DS/EN 353-1:2002 防止从高处坠落的个人防护设备 第1部分：包括刚性锚索的导向型坠落制动器

This European Standard specifies the requirements, test methods, marking, information supplied by the manufacturer and packaging for guided type fall arresters including a rigid anchor line usually attached to or integrated in fixed ladders or rungs adequately adjusted to suitable structures. Guided type fall arresters including a rigid anchor line conforming to this European Standard are sub-systems constituting one of the fall arrest systems covered by EN 363, when combined with full body harness specified in EN 361 including a front attachment point located appropriately in relation to the fall arrester. Other types of fall arresters are specified in EN

Personal protective equipment against falls from a height - Part 1: Guided type fall arresters including a rigid anchor line

DS/EN 353-2:2002 防止从高处坠落的个人防护设备 第2部分：包括柔性锚索的导向型防坠器

This European Standard specifies the requirements, test methods, marking, information supplied by the manufacturer and packaging for guided type fall arresters including a flexible anchor line which can be secured to an upper anchor point. Guided type fall arresters including a flexible anchor line conforming to this European Standard are sub-systems constituting a part of one of the fall arrest systems covered by EN 363. Other types of fall arresters are specified in EN 353-1 or EN 360. Energy absorbers are specified in EN 355.

Personal protective equipment against falls from a height - Part 2: Guided type fall arresters including a flexible anchor line

DS/EN 355:2002 防止从高处坠落的个人防护设备 能量吸收器

This European Standard specifies the requirements, test methods, marking, information supplied by the manufacturer and packaging for energy absorbers. Energy absorbers conforming to this European Standard are used as elements or components either intergrated in a lanyard, an anchor line or a full body harness or in combination with one of them. Combinations of an energy absorber and a lanyard are sub-systems constituting one of the fall arrest systems covered by EN 363, when combined with a full body harness specified in EN 361. Fall arresters are specified in EN 353-1, EN 353-2 and EN 360.

Personal protective equipment against falls from a height - Energy absorbers

DS/EN 361:2002 防止从高处坠落的个人防护设备 全身式安全带

The European Standard specifies the requirements, test methods, marking, information supplied by the manufacturer and packaging for full body harnesses. Other types of body support specified in other European Standards, e.g. EN 358, EN 813 or EN 1497, may be incorporated into the full body harness. Fall arrest systems are specified in EN 363.

Personal protective equipment against falls from a height - Full body harnesses

NF S71-508*NF EN 361:2002 防高处坠落用个人防护设备.全身式吊带

Personal protective equipment against falls from a height - Full body harnesses.

DIN EN 360:2002 防止人员从高处跌落的保护设备.回收型跌落保护装置; 德文版本 EN 360:2002

This European Standard specifies the requirements, test methods, information supplied by the manufacturer and marking for retractable type fall arresters. Retractable type fall arresters according to this European Standard are used in fall arrest systems specified in EN 363 in conjunction with full body harnesses specified in EN 361. Other types of fall arresters are specified in EN 353-1 and EN 353-2, and energy absorbers are specified in EN 355.#,,#

Personal protective equipment against falls from a height - Retractable type fall arresters; German version EN 360:2002

DIN EN 361:2002 防止人员从高处跌落的保护设备.全身保护安全带; 德文版本 EN 361:2002

This European Standard specifies the requirements, test methods, information supplied by the manufacturer, marking and packaging for full body harnesses. Other types of body support, specified in other European Standard, may be incorporated into the full body harness. Fall arrest systems are specified in EN 363. Rescue harnesses are specified in EN 1497.#,,#

Personal protective equipment against falls from a height - Full body harnesses; German version EN 361:2002

DIN EN 353-1:2002 防止人员从高处跌落的保护设备.第1部分:设有刚性铰链的导向跌落保护装置; 德文版本 EN 353-1:2002

This European Standard specifies the requirements, test methods, information supplied by the manufacturer and marking for guided type fall arresters including a rigid anchorage line usually attached to or integrated in climbing ladders or climbing iron tracks adequately adjusted to suitable structures. Guided type fall arresters according to this European Standard are used in fall arrest systems specified in EN 363 in conjunction with full body harnesses specified in EN 361. Other types of fall arresters are specified in EN 360 and in EN 353-2. Energy absorbers are specified in EN 355.

Personal protective equipment against falls from a height - Part 1: Guided type fall arresters including a rigid anchor line; German version EN 353-1:2002

DIN EN 353-2:2002 防止人员从高处跌落的保护设备.第2部分:设有柔性铰链的导向跌落保护装置; 德文版本 EN 353-2:2002

This European Standard specifies the requirements, test methods, information supplied by the manufacturer and marking for guided type fall arresters including a flexible anchorage line which can be secured to an upper anchorage point. Guided type fall arresters according to this European Standard are used in fall arrest systems specified in EN 363 in conjunction with full body harnesses specified in EN 361. Other types of all arresters are specified in EN 360 and in EN 353-1. Energy absorbers are specified in EN 355.

Personal protective equipment against falls from a height - Part 2: Guided type fall arresters including a flexible anchor line; German version EN 353-2:2002

DIN EN 355:2002 防止人员从高处跌落的保护设备.能量减震器; 德文版本 EN 355:2002

This European Standard specifies the requirements, test methods, information supplied by the manufacturer, marking and packaging for energy absorbers. Energy absorbers according to this European Standard are used in fall arrest systems specified in EN 363 either integrated in a lanyard or in combination with a lanyard ready for use. Fall arresters are specified in EN 353-1, EN 353-2 and EN 360.

Personal protective equipment against falls from a height - Energy absorbers; German version EN 355:2002

BS EN 1263-2:2002 安全网.定位极限的安全性要求

This European Standard specifies safety requirements for the positioning of safety nets in accordance with the manufacturer's instruction manual and with the product specifications and for the testing of system S, system T, system U and system V safety nets in accordance with EN 1263-1. Small safety nets of system S according to EN 1263-1 (less than 35 m and 5,0 m on the shortest side) are not dealt with in this European Standard.

Safety nets - Safety requirements for the positioning limits