13.340.60 标准查询与下载

EN 1263-2:2002 安全网.第2部分:定位区域的安全要求

This European Standard specifies safety requirements forThe positioning of safety nets in accordance withThe manufacturer's instruction manual and withThe product specifications and forThe testing of system S, system T, system U and system V safety nets in accordance with EN 1263-1. Small safety nets of system S according to EN 1263-1 (less than 35 m and 5,0 m onThe shortest side) are not dealt with inThis European Standard.#,,#

Safety Nets - Part 2: Safety Requirements for the Positioning Limits

BS EN 361:2002 预防从高空坠落用的人员保护设备.全身保护背带吊具

This European Standard specifies the requirements, test methods, marking, information supplied by the manufacturer and packaging for full body harnesses. Other types of body support, specified in other European Standards, e. g. EN 358, EN 813 or EN 1497, may be incorporated into the full body harness. Fall arrest systems are specified in EN 363.

Personal protective equipment against falls from a height - Full body harnesses

BS EN 363:2002 预防从高空坠落用的人员保护设备.防止坠落装置

This European Standard specifies the terminology and the general requirements for fall arrest systems which serve as personal protective equipment against falls from a height. This European Standard additionally describes examples of how components or assemblies of components may be connected into a fall arrest system. These examples should enable the purchaser or user to assemble all components in a correct manner and to build up a fall arrest system.

Personal protective equipment against falls from a height - Fall arrest systems

BS EN 360:2002 预防从高空坠落的人员保护设备.伸缩型防坠落装置

This European Standard specifies the requirements, test methods, marking, information supplied by the manufacturer and packaging for retractable type fall arresters. Retractable type fall arresters conforming to this European Standard are sub-systems constituting one of the fall arrest systems covered by EN 363, when combined with a full body harness specified in EN 361. Other types of fall arresters are specified in EN 353-1 and EN 353-2. Energy absorbers are specified in EN 355.

Personal protective equipment against falls from a height - Retractable type fall arresters

BS EN 355:2002 预防从高空坠落用的人员保护设备.能量吸收器

This European Standard specifies the requirements, test methods, marking, information supplied by the manufacturer and packaging for energy absorbers. Energy absorbers conforming to this European Standard are used as elements or components either integrated in a lanyard, an anchor line or a full body harness or in combination with one of them. Combinations of an energy absorber and a lanyard are sub-systems constituting one of the fall arrest systems covered by EN 363, when combined with a full body harness specified in EN 361. Fall arresters are specified in EN 353-1, EN 353-2 and EN 360.

Personal protective equipment against falls from a height - Energy absorbers

BS EN 354:2002 预防从高空坠落用的人员保护设备.短绳

This European Standard specifies the requirements, test methods, marking, information supplied by the manufacturer and packaging for non-adjustable and adjustable lanyards. Lanyards conforming to this European Standard are used as connecting elements or components in fall arrest systems specified in EN 363. Other types of lanyards are specified in EN 358.

Personal protective equipment against falls from a height - Lanyards

BS EN 353-2:2002 预防从高空坠落用的人员保护设备.包括柔性锚固定链的定向型防坠落装置

This European Standard specifies the requirements, test methods, marking, information supplied by the manufacturer and packaging for guided type fall arresters including a flexible anchor line which can be secured to an upper anchor point. Guided type fall arresters including a flexible anchor line conforming to this European Standard are sub- systems constituting a part of one of the fall arrest systems covered by EN 363. Other types of fall arresters are specified in EN 353-1 or EN 360. Energy absorbers are specified in EN 355.

Personal protective equipment against falls from a height - Guided type fall arresters including a flexible anchor line

BS EN 353-1:2002 预防从高空坠落用的人员保护设备.包括刚性锚固定链的定向型防坠落装置

This European Standard specifies the requirements, test methods, marking, information supplied by the manufacturer and packaging for guided type fall arresters including a rigid anchor line usually attached to or integrated in fixed ladders or rungs adequately adjusted to suitable structures. Guided type fall arresters including a rigid anchor line conforming to this European Standard are sub-systems constituting one of the fall arrest systems covered by EN 363, when combined with a full body harness specified in EN 361 including a front attachment point located appropriately in relation to the fall arrester. Other types of fall arresters are specified in EN 353-2 or in EN 360. Energy absorbers are specified in EN 355.

Personal protective equipment against falls from a height - Guided type fall arresters including a rigid anchor line

DIN EN 1263-1:2002 安全网络.第1部份:安全要求、试验方法; 德文版本 EN 1263-1:2002

This European Standard is applicable to safety nets and their accessories for use in construction, scaffolding, falsework and assembly work and specifies safety requirements and test methods. This product standard does is not applicable to the installation of safety nets. For a European Standard covering the installation of safety nets see prEN 1263-2:1995.

Safety nets - Part 1: Safety requirements, test methods; German version EN 1263-1:2002

BS EN 1263-1:2002 安全网.安全性要求,试验方法

This European Standard applies to safety nets and their accessories for use in construction and assembly work to protect from deeper fall. It specifies safety requirements and test methods and is based on the performance characteristics of polypropene and polyamide fibres. Materials used in nets should have no significant reduction in mechanical properties between - 10 ℃ and + 40 ℃. This standard is not applicable to the installation of safety nets. For a European Standard covering the installation of safety nets see EN 1263-2.

Safety nets - Safety requirements, test methods

EN 353-2:2002 预防高空坠落的人身保护设备.第2部分:包括挠性锚固线的指导型防坠落装置

This European Standard specifies the requirements, test methods, marking, information supplied byThe manufacturerand packaging for guided type fall arresters including a flexible anchor line which can be secured to an upper anchorpoint. Guided type fall arresters including a flexible anchor line conforming toThis European Standard are su卜systems constituting a part of one of the fall arrest systems covered by EN 363. Other types of fall arresters arespecified in EN 353-1 or EN 360. Energy absorbers are specified in EN 355.

Personal protective equipment against falls from a height - Part 2: Guided type fall arresters including a flexible anchor line

EN 361:2002 预防高空坠落的人员保护设备.全身保护成套装置

This European Standard specifies the requirements, test methods, marking, information supplied byThemanufacturer and packaging for full body harnesses. Other types of body support, specified in other EuropeanStandards, e. g. EN 358, EN 813 or EN 1497, may be incorporated intoThe full body harness. Fall arrest systemsare specified in EN 363.

Personal protective equipment against falls from a height - Full body harnesses

ISO 10333-4:2002 人员坠落救护系统.第4部分:垂直下落和滑动型下落救护车连接的垂直升降索道

This part of ISO 10333 specifies requirements, test methods, instructions for use and maintenance, marking, labelling and packaging, as appropriate, for vertical rails and vertical lifelines which incorporate a sliding-type fall arrester. When connected to a full-body harness as specified in ISO 10333-1, vertical rails and vertical lifelines which incorporate a sliding-type fall arrester constitute a personal fall-arrest system (PFAS), which will be specified in a future International Standard. Vertical rails and vertical lifelines which incorporate a sliding-type fall arrester in accordance with this part of ISO 10333 are limited to use by a single person of total mass not exceeding 100 kg. NOTE 1 Users of PFAS whose total mass (which includes attached tools and equipment) exceeds 100 kg are advised to seek advice from the equipment manufacturers regarding the suitability of the equipment, which may need additional testing. NOTE 2 PFAS using vertical rails and permanent vertical lifelines inherently limit the user's horizontal movement, whereas PFAS using a temporary vertical lifeline permit significant horizontal movement by the user. Special notice should be given to the requirements which accommodate this difference. The scope of this part of ISO 10333 does not extend to: a) inclined rails and lifelines, i.e. those which are installed at an angle between the true vertical and the lifeline or rail of more than 15°when viewed from the side elevation; b) the horizontally installed elements of compound rails or lifelines, i.e. those which have both vertically and - horizontally installed elements linked by junctions. This part of ISO 10333 does not specify those additional requirements that would apply when PFAS are subjected to special conditions of use (where, for example, there exist unusual limitations concerning access to the place of work and/or particular environmental factors). Thus treatments to ensure the durability of the materials of construction (such as heat treatment, anti-corrosion treatment, protection against physical and chemical hazards) are not specified in this part of ISO 10333, but should comply with appropriate International Standards or, failing that, with national standards or other specifications dealing with relevant physical characteristics and/or the safety of users.

Personal fall-arrest systems - Part 4: Vertical rails and vertical lifelines incorporating a sliding-type fall arrester

ISO 10333-1:2000/Amd 1:2002 防人员坠落系统.第1部分:全套衣帽装备.修改件1

This is Amendment 1 ISO 10333-1-2000 (Personal fall-arrest systems —Parti:Full-body harnesses AMENDMENT 1)

Personal fall-arrest systems - Part 1: Full-body harnesses; Amendment 1

ISO 10333-5:2001 个人防跌落系统 第5部分：带有自动关闭和自动锁门的连接器

This part of ISO 10333 specifies requirements, test methods, instructions for use and maintenance, marking, labelling and packaging, as appropriate, for connectors with self-closing and self-locking gates made from metallic materials. Connectors are used in personal fall-arrest systems (PFAS), which will be specified in a future International Standard (see ISO 10333-6 in the Bibliography), such that, if an arrest takes place, the arresting force will not exceed 6kN. This part of ISO 10333 is applicable only to connectors limited to single person use of a total mass not exceeding 100 kg. NOTE Users of fall protection equipment whose total mass (including tools and equipment) exceeds 100 kg are advised to seek advice from the equipment manufacturer regarding the suitability of this equipment, which may need additional testing. The scope of this part of ISO 10333 does not extend to: a) attachment elements, fastening buckles, adjusting buckles and other metallic fittings used in the manufacture of full-body harnesses, which are specified in ISO 10333-6; b) connectors used for material-lifting purposes; c) connectors used in special techniques or situations, e.g. rescue, or rope access. This part of ISO 10333 does not specify those additional requirements that would apply when connectors are subjected to special conditions of use (where, for example, there exist unusual limitations concerning access to the place of work and/or particular environmental factors). Thus, treatments to ensure the durability of the materials of construction (such as heat treatment, anti-corrosion treatment, protection against physical and chemical hazards) are not specified in this part of ISO 10333, but should comply with appropriate International Standards or, failing that, with national standards and other specifications dealing with relevant physical characteristics and/or the safety of users. In particular, when it is considered necessary to test the corrosion resistance of metallic parts of the equipment, reference should be made to ISO 9227.

Personal fall-arrest systems - Part 5: Connectors with self-closing and self-locking gates

DIN 34300:2001 救护设备.带安全绳环的救护钩

The document specifies requirements, test methods, instructions for use and marking for rescue hooks with safety eyelet holes including load bearing rope and additonal protection. Rescue hooks with safety eyelet holes are components of personal protective equipment for rescue of persons by a rescuer. Rescue hooks with safety eyelet holes are used in connection with an additional protection for example a fall arrest system following DIN EN 363 set up for the expected weight.

Rescue equipment - Rescue hooks with safety eyelet holes

AS/NZS 1891.2/SUPP 1:2001 工业防坠系统和设备.水平救生索和围栏系统.水平救生索的规定结构

Specifies a range of system configurations which have been determined by investigation to meet the performance and safety requirements of AS/NZS 1891.2. It also specifies hardware and installation requirements for such systems.

Industrial fall-arrest systems and devices - Horizontal lifeline and rail systems - Prescribed configurations for horizontal lifelines (Supplement to AS/NZS 1891.2:2001)

CAN/CSA-Z259.12-2001(R2011) 个人防坠落系统 (PFAS) 的连接组件

1. Scope 1.1 This Standard sets out design and performance requirements, test methods, and requirements for marking and labelling individual connecting components used as part of a personal fall arrest system (PFAS). This Standard applies to components that are (a) used in the interconnection of a complete unit referred to in other published Standards and/or projected Standards related to PFAS; (b) intended to be used as the primary single link to a permanent anchorage connector; and (c) intended to be used as a primary attachment point between two or more subsystems, as described and certified under other Standards related to PFAS. 1.2 This Standard does not apply to anchorages or anchorage connectors.

Connecting Components for Personal Fall Arrest Systems (PFAS)

NF S71-513/A1:2000 高处坠落防护.锚固装置.要求和试验

Protection against falls from a height - Anchor devices - Requirements and testing.

CAN/CSA-Z259.2.2-1998(C2009) 用于防坠落装置的自动回缩绳索装置

1. Domaine d'application 1.1 Cette norme énonce des exigences visant les dispositifs à cordon autorétractable utilisés comme organes de raccordement sur des dispositifs antichutes individuels. Les dispositifs à cordon autorétractable sont classés selon le mode d'utilisation et la longueur efficace. 1.2 Le matériel visé par cette norme est destiné aux travailleurs qui risquent de faire des chutes. 1.3 Cette norme énonce des exigences visant l'étiquetage des produits et les instructions d'utilisation qui indiquent aux utilisateurs les limites de performance, les méthodes d'inspection et d'entretien ainsi que les risques découlant d'une mauvaise utilisation. 1.4 Certains dispositifs à cordon autorétractable pour dispositifs antichutes comportent un moyen de sauvetage après une chute interrompue.

Self-retracting cord devices for fall arrest devices