13.340.60 标准查询与下载

DS/EN 358:2000 工作定位和防止从高处坠落的个人防护设备 工作定位和约束带以及工作定位系索

This European standard applies to belts and lanyards intended for the purpose of work positioning or restraint. It specifies the requirements, testing, marking and information supplied by the manufacturer.

Personal protective equipment for work positioning and prevention of falls from a height - Belts for work positioning and restraint and work positioning lanyards

ISO 10333-1:2000 个体防跌落系统 第1部分:整体吊带

This part of ISO 10333 specifies the requirements, test methods, instructions for general use, marking, packaging and maintenance for full-body harnesses (FBH). The main purpose of a FBH is to allow the user to connect into a personal fall-arrest system (PFAS), which will be specified in a future International Standard (see ISO 10333-6 in the Bibliography), such that if an arrest takes place, the arresting force will not exceed 6 kN. For the purposes of this part of ISO 10333, FBH may have attachment elements that allow the user to connect into other types of safety or access system, for example a work-positioning system, a controlled descent/ascent system or a confined-space access system. This part of ISO 10333 includes requirements for such attachment elements. This part of ISO 10333 is applicable only to FBH limited to single-person use of a total mass not exceeding 100 kg. NOTE Users of fall-protection equipment whose total mass (including tools and equipment) exceeds 100 kg are advised to seek advice from the equipment manufacturer regarding the suitability of the equipment, which may need additional testing. The scope of this part of ISO 10333 does not extend to: a) waist belts or chest harnesses: such equipment is not considered as safe to use in personal fall-arrest systems (PFAS); b) all other types of harnesses that are not designed primarily for use in PFAS; c) other special requirements for FBH, peculiar to use in a controlled descent/ascent system or a confined-space access system; d) any assessment of compatibility or suitability in respect of the performance of FBH in a controlled descent/ascent system or a confined-space access system. This part of ISO 10333 does not specify those additional requirements that would apply when harnesses are subjected to special conditions of use (where, for example, there exist unusual limitations concerning access to the place of work and/or particular environmental factors). Thus treatments to ensure the durability of the materials of construction (such as heat treatment, anti-corrosion treatment, protection against physical and chemical hazards) are not specified in this part of ISO 10333, but should comply with appropriate International Standards or, failing that, with national standards and other specifications dealing with relevant physical characteristics and/or the safety of users. In particular, when it is considered necessary to test the corrosion resistance of metallic parts of the equipment, reference should be made to ISO 9227.

Personal fall-arrest systems - Part 1: Full-body harnesses

ISO 10333-3:2000 个体防跌落系统 第3部分:自控器

This part of 10333 specifies requirements, test methods, instructions for use and maintenance, marking, labelling and packaging, as appropriate, for self-retracting lifelines, including self-retracting lifelines that have an integral-rescue facility. Self-retracting lifelines are used as a connecting sub-system in personal fall-arrest systems (PFAS), which will be specified in a future International Standard (see ISO 10333-6 in the Bibliography), and are attached to anchor devices that are above the work place. This part of 10333 is applicable only to self-retracting lifelines limited to single-person use of a total mass not exceeding 100 kg. NOTE Users of PFAS whose total mass (which includes attached tools and equipment) exceeds 100 kg are advised to seek advice from the equipment manufacturers regarding the suitability of the equipment, which may need additional testing to take into account the larger mass. This part of 10333 does not specify those additional requirements that would apply when self-retracting lifelines are subjected to special conditions of use (where, for example, there exist unusual limitations concerning access to the place of work and/or particular environmental factors). Thus treatments to ensure the durability of the materials of construction (such as heat treatment, anti-corrosion treatment, protection against physical and chemical hazards) are not specified in this part of 10333, but should comply with appropriate International Standards or, failing that, with national standards and other specifications dealing with relevant physical characteristics and/or the safety of users.

Personal fall-arrest systems - Part 3: Self-retracting lifelines

BS EN 358:2000 工作定位和防止从高处坠落的个人防护设备.工作定位和限动用固定带及工作定位用牵索

Specifies requirements, testing, marking, labelling and packaging of equipment that is intended for work positioning and support of users working at a height (including the prevention of a free fall) but that is not intended to be used to arrest a fall.

Personal protective equipment for work positioning and prevention of falls from a height - Belts for work positioning and restraint and work positioning lanyards

NF S71-505:2000 控制工作位置和防止从高处坠落的人员防护设备.控制和限制工作位置的安全带以及控制工作位置的小短索

Personal protective equipment for work positioning and prevention of falls from a height - Belts for work positioning and restraint and work positioning lanyards.

ISO 10333-2:2000 个体防跌落系统 第2部分:缓冲器

This part of ISO 10333 specifies requirements, test methods, instructions for use and maintenance, marking, labelling and packaging, as appropriate, for lanyards and energy absorbers. Lanyards and energy absorbers are used together as a connecting subsystem in personal fall-arrest systems (PFAS) which will be specified in a future International Standard (see ISO 10333-6 in the Bibliography). Two classes of energy absorbers are specified for the purposes of this part of ISO 10333: a) Type 1: used in PFAS where, due to installation, the potential free-fall distance can be limited to a maximum of 1,8 m and, if a fall takes place, the arresting force is limited to a maximum of 4,0 kN; b) Type 2: used in PFAS where, due to installation, the potential free-fall distance can be limited to a maximum of 4,0 m and, if a fall takes place, the arresting force is limited to a maximum of 6,0 kN. This part of ISO 10333 is applicable only to lanyards and energy absorbers limited to single-person use of a total mass not exceeding 100 kg. NOTE Users of fall-protection equipment whose total mass (including tools and equipment) exceeds 100 kg are advised to seek advice from the equipment manufacturer regarding the suitability of this equipment, which may need additional testing. For the purposes of this part of ISO 10333, energy absorbers may be supplied integral to a lanyard, integral to a full body harness (FBH), or may be supplied separately. The scope of this part of ISO 10333 does not extend to: a) PFAS that incorporate lanyards without energy absorbers or without a means of energy dissipation; b) special lanyards and energy absorbers which are integral (i.e. can only be separated by mutilation or by special tool) to the PFAS components as specified in ISO 10333-4. This part of ISO 10333 does not specify those additional requirements that would apply when lanyards and energy absorbers are subjected to special conditions of use (where, for example, there exist unusual limitations concerning access to the place of work and/or particular environmental factors). Thus treatments to ensure the durability of the materials of construction (such as heat treatment, anti-corrosion treatment, protection against physical and chemical hazards) are not specified in this part of ISO 10333, but should comply with appropriate International Standards or, failing that, with national standards and other specifications dealing with relevant physical characteristics and/or the safety of users. In particular, when it is considered necessary to test the corrosion resistance of metallic parts of the equipment, reference should be made to ISO 9227.

Personal fall-arrest systems - Part 2: Lanyards and energy absorbers

DIN EN 358:2000 控制工作位置和防止从高处坠落的人员防护设备.工作定位、约束和工作用的安全带和牵索

The document applies to belts and lanyards intended for the purpose of work positioning of restraint. It specifies the requirements, testing, marking and information supplied by the manufacturer.

Personal protective equipment for work positioning and prevention of falls from a height - Belts for work positioning and restraint and work positioning lanyards; German version EN 358:1999

ISO 14567:1999 防止从高处坠落的个人防护装置 单点锚定设备

This International Standard specifies requirements, test methods, and marking, labelling and packaging, as appro-priate, of both permanent and temporary single-point anchor devices exclusively for the attachment of personal protective equipment (PPE) for protection against falls from a height for fall arrest, work positioning and travel restriction (work restraint). It is applicable only to anchor devices for PPEs that conform to ISO 10333-1, ISO 10333-2, ISO 10333-3 and ISO 10333-5. NOTE 1 Further standards are in preparation for other types of PPE: ISO 10333-6 and ISO 14566 (see bibliography). Anchor devices are rated to sustain a maximum (dynamic) arresting force of 6,0 kN, and a maximum (static) loading of 1,0 kN (assuming a person of 100 kg mass) in post-fall arrest suspension, work-positioning mode, or restraint mode. Anchor devices are intended for single person use only. A rescuer should not attach to the same anchor device as a person being rescued, unless the anchor device has been specifically designed for such purposes, and the instructions for use specifically permit this application. NOTE 2 Vertical rigid or flexible line systems and horizontal lifelines are not within the scope of this International Standard, but are covered in ISO 10333-4 and ISO 16024.

Personal protective equipment for protection against falls from a height - Single-point anchor devices

DS/EN 1891:1999 防止高处坠落的个人防护设备 低弹力绳索

This European Standard applies to low stretch textile ropes of kernmantel construction from 8,5 mm to 16 mm diameter, for use by persons in rope access including all kinds of work positioning and restraint; for rescue and in speleology. Two types of low stretch kernmantel rope are defined: A and B. The European Standard specifies requirements, testing, marking and information to be supplied by the manufacturer including instructions for use of such low stretch kernmantel ropes.

Personal protective equipment for the prevention of falls from a height - Low stretch kernmantel ropes

EN 358:1999 控制工作位置和防止从高处坠落的人员防护设备.工作定位,约束和工作用的安全带和牵索

This European Standard applies to belts and lanyards intended forThe purpose of work positioning or restraint. It specifiesthe requirements, testing, marking and information supplied byThe manufacturer.

Personal Protective Equipment for Work Positioning and Prevention of Falls from a Height - Belts for Work Positioning and Restraint and Work Positioning Lanyards

BS EN 1891:1998 防高处坠落个人保护设备.低弹力纤维绳索

This European Standard applies to low stretch textile ropes of kernmantel construction from 8,5 mm to 16 mm diameter, for use by persons in rope access including all kinds of work positioning and restraint; for rescue and in speleology. Two types of low stretch kernmantel rope are defined: A and B. The European Standard specifies requirements, testing, marking and information to be supplied by the manufacturer including instructions for use of such low stretch kernmantel ropes. NOTE 1 It is possible that rope not conforming to this European Standard may also be suitable for the activities described above. NOTE 2 Ropes used for protection during any free climbing activity in rope access, rescue or speleology should take account of other standards, e.g. EN 892. Dynamic mountaineering rope may also be used for protection during rope access and work positioning.

Personal protective equipment for the prevention of falls from a height - Low stretch kernmantel ropes

CAN/CSA-Z259.2.2-1998(R2009) 用于个人防坠落系统的自动回缩装置

1. Scope 1.1 This Standard specifies the requirements for all self-retracting devices (SRDs) used as connecting components in personal fall-arrest systems. SRDs are further classified in this Standard according to method of use and effective length. 1.2 The equipment specified in this Standard is intended for users at risk of potential falls from height while at work. 1.3 This Standard outlines requirements for labelling products and providing instructions for use that will inform the user of performance limitations, inspection, maintenance, and hazards associated with misuse. 1.4 Some self-retracting devices for personal fall-arrest systems incorporate a means of worker retrieval following a fall-arrest incident.

Self-Retracting Devices for Personal Fall-Arrest Systems

NF S71-519*NF EN 1891:1998 防止由高处跌落的个人防护设备.低膨胀芯套绳索

Personal protective equipment for the prevention of falls from ů height - Low stretch kernmantel ropes.

DIN EN 1891:1998 预防个人从高处坠落的保护设备.低延伸性芯套绳索

The document applies to low stretch textile ropes of kernmantel construction 8,5 mm to 16 mm diameter, for use by personnel in rope access including all kinds of work positioning and restraint; for rescue and in speleology. Two types of low stretch kernmantel ropes are defined: A and B. It specifies requirements, testing, marking and information to be supplied by the manufacturer including instructions for use of such low stretch kernmantel ropes.

Personal protective equipment for the prevention of falls from a height - Low stretch kernmantel ropes; German version EN 1891:1998

EN 1891:1998 防高处坠落用个人保护设备.低弹力纤维绳索

This European Standard applies to low stretch textile ropes of kernmantel construction from 8,5 mm to 16 mm diameter, for use by persons in rope access including all kinds of work positioning and restraint; for rescue and in speleology. Two types of low stretch kernmantel rope are defined:A and B.The European Standard specifies requirements, testing, marking and information to be supplied byThe manufacturer including instructions for use of such low stretch kernmantel ropes.NOTE 1 It is possible that rope not conforming toThis European Standard may also be suitable forThe activities described above.NOTE 2 Ropes used for protection during any free climbing activity in rope access, rescue or speleology should take account of other standards, e.g. EN 892. Dynamic mountaineering rope may also be used for protection during rope access and work positioning.

Personal protective equipment for the prevention of falls from a height - Low stretch kernmantel ropes

NF S71-606:1998 娱乐艇甲板安全带和安全线.安全要求和试验方法

Deck safety harness and safety line for use on recreational craft. Safety requirements and test methods.

BS EN 1868:1997 防人员坠落设备.相同含义名称表

This European Standard is applicable to personal protective equipment against falls from a height. This European Standard specifies a list of terms used to define personal protective equipment against falls from a height. The terms are listed in alphabetical order in the three official languages of CEN, English, French and German. The terms or explanations given in parentheses are added exclusively for better understanding.

Personal protective equipment against falls from a height - List of equivalent terms

DIN EN 1868:1997 防人员坠落设备.等义术语表

The document is applicable to personal protective equipment against falls from a height. It specifies a list of terms used to define personal protective equipment against falls from height.

Personal protective equipment against falls from a height - List of equivalent terms; German version EN 1868:1997

NF S71-514:1997 防高处坠落的个人防护设备.座位挽具(欧洲标准EN 813)

Personal protective equipment for prevention of falls from a height. Sit harnesses.

EN 1868:1997 防坠落人员保护设备.等效术语表

This European Standard is applicable to personal protective equipment against falls from a height.This European Standard specifies a list of terms used to define personal protective equipment against falls from a height.The terms are listed in alphabetical order inThe three official languages of CEN, English, French and German.The terms or explanations given in parentheses are added exclusively for better understanding.

Personal Protective Equipment Against Falls from a Height - List of Equivalent Terms