17.040.01 长度和角度测量综合 标准查询与下载

GSO ISO 1:2024 产品几何规范 (GPS) 几何和尺寸特性规范的标准参考温度

This document defines the concepts of a reference temperature and the standard reference temperature and specifies the standard reference temperature value for the specification of geometrical and dimensional properties of an object. Some examples of geometrical and dimensional properties include size, location, orientation (including angle), form and surface texture of a workpiece. This document is also applicable to the definition of the measurand used in verification or calibration.

Geometrical product specifications (GPS) — Standard reference temperature for the specification of geometrical and dimensional properties

T/QGCML 3248-2024 景观设计环境坡度检测装置

本文件规定了景观设计环境坡度检测装置的术语和定义、构成及原理、要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于景观设计环境坡度检测装置的生产及检验。

Landscape design environment slope detection device

T/SXICS 004-2023 带直尺的量角器校准规范

1 范围 2 规范性引用文件 3 概述 4 一般要求 5 计量特性 6 校准条件 6.1 环境条件 6.2 测量标准及其他设备 7 校准项目和校准方法 7.1 校准项目 7.2 校准方法 8 校准结果表达 9 校准间隔 附录 A（资料性） 角度示值误差的不确定度评定示例 附录 B（资料性） 直尺示值误差的不确定度评定示例 附录 C（资料性） 校准证书内页格式

calibration specification for protractors with a ruler

T/QGCML 2383-2023 自动测量钢管长度检测装置

本文件规定了自动测量钢管长度检测装置的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于自动测量钢管长度检测装置。

Automatic steel pipe length detection device

T/SPSTS 030-2023 石墨烯材料 片径尺寸测量 扫描电子显微镜法

本文件规定了利用扫描电子显微镜法测量石墨烯材料片径尺寸的术语和定义、原理、仪器设备、试剂和材料、结果分析和测试报告内容。 本文件适用于石墨烯材料片径尺寸的测量。

Graphene material sheet size measurement using scanning electron microscopy

T/NXJX 054-2023 带式输送机过渡、过盈配合零件的装配 技术要求

本文件规定了带式输送机核心部件装配用工装的设计、评审、制作、验证、使用、保管和报废全过程的管理。 本文件适用于带式输送机核心部件装配用工装的管理。

Technical requirements of assembly for transitional and interference fitting parts of belt conveyors

T/SJZSYYQXH JZ006-2023 轻骨料承压筒校准方法

7、　校准方法 7.1、　外观 目测和手摸内外表面是否光滑、平整、是否镀铬，尺寸刻度线是否清晰。 7.2、　配合 各部分应能自由滑动。 7.3、　几何尺寸 游标卡尺测量、选均匀分布的三点进行测量，三次测量平均值为测量结果，三次测量结果均应符合要求。 7.4、　筒外壁尺寸刻度线与底面的距离 游标卡尺测量、测量三次，取算术平均值为测量结果，三次测量结果均应符合设备技术要求。 7.5、　筒体、导向筒和冲压模上下表面与柱面的垂直度 用直角尺和塞尺测量筒体、导向筒和冲压模上下表面与柱面的垂直度，测量三次，算术平均值为测量结果，三次测量结果均应符合要求。

Calibration method of lightweight aggregate pressure-bearing cylinder

T/SJZSYYQXH JZ005-2023 冷弯弯芯校准方法

7.1弯芯长度校准 用钢直尺测量各冷弯弯芯长度，测量三次取平均值作为校准结果。 7.2弯心直径校准 用数显卡尺测量各冷弯弯芯直径，测量三次取平均值作为校准结果。 对于无法用数显卡尺测量的冷弯弯芯直径，可使用分辨力0.01mm的数显半径规进行校准，测量三次取平均值作为校准结果。 8校准结果处理 经校准的冷弯弯芯出具校准证书，校准证书应给出校准结果及其测量不确定度。 9校准间隔 建议校准时间间隔不超过1年。使用单位可根据校准结果、使用频次、使用条件等情况自行确定复校的时间间隔。 在此期间内如果在此检具经过调修，建议重新校准。

Cold bending core calibration method

T/SMA 0034-2023 转站式坐标测量系统校准规范——基于靶标瞄准部分

本文件规定了转站式坐标测量系统—基于靶标瞄准部分（以下简称：转站式坐标测量系统）校准的计量特性、校准条件、校准项目、校准方法、校准结果的处理、复校时间间隔。 本文件适用于基于靶标瞄准的转站市坐标测量系统的校准。

Calibration Specification for Coordinate Measuring System By Transfer Station ——Based on Target Aiming Part

KS B 5246-2022 金属直尺

Metal straight rulers

ASTM F2203-13(2022) 用精密钢尺进行线性测量的标准试验方法

1.1 This test method covers the measurement of linear dimension of flexible packages and packaging materials. It is recommended for use with an allowable tolerance range of 3 mm (1⁄8 in.) or greater based on gauge repeatability and reproducibility presented in the Precision and Bias section. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Linear Measurement Using Precision Steel Rule

T/FJSJLCSXH 002-2022 地下管线探测用探地雷达技术规范

本文件规定了地下管线探测用探地雷达的性能要求及检验方法。

Technical specification of ground penetration radar for underground pipeline detection

BS EN ISO 1:2022 产品几何规格(GPS)几何和尺寸特性规范的标准参考温度

1   Scope This document defines the concepts of a reference temperature and the standard reference temperature and specifies the standard reference temperature value for the specification of geometrical and dimensional properties of an object. Some examples of geometrical and dimensional properties include size, location, orientation (including angle), form and surface texture of a workpiece. This document is also applicable to the definition of the measurand used in verification or calibration.

Geometrical product specifications (GPS). Standard reference temperature for the specification of geometrical and dimensional properties

EN ISO 1:2022 产品几何技术规范(GPS)-几何和尺寸性能规格标准参考温度

This document defines the concepts of a reference temperature and the standard reference temperature and specifies the standard reference temperature value for the specification of geometrical and dimensional properties of an object. Some examples of geometrical and dimensional properties include size, location, orientation (including angle), form and surface texture of a workpiece. This document is also applicable to the definition of the measurand used in verification or calibration.

Geometrical product specifications (GPS) - Standard reference temperature for the specification of geometrical and dimensional properties (ISO 1:2022)

ISO 1:2022 产品几何技术规范（GPS）.几何和尺寸特性规范的标准参考温度

This document defines the concepts of a reference temperature and the standard reference temperature and specifies the standard reference temperature value for the specification of geometrical and dimensional properties of an object. Some examples of geometrical and dimensional properties include size, location, orientation (including angle), form and surface texture of a workpiece. This document is also applicable to the definition of the measurand used in verification or calibration.

Geometrical product specifications (GPS) — Standard reference temperature for the specification of geometrical and dimensional properties

T/CAQ 20201-2022 机电产品 基于三维模型的数字化检验实施指南

数字化研制环境下，产品设计、工艺、制造以及过程质量管理要求和方法都作出了相应转变，制造过程的管控对象从单一的实物验证向虚拟验证和预防控制转变；质量控制方式从单一的事后把关向数据自动采集、过程在线监督转变；生产过程的检验依据、工作流程、测量方法、检验手段和检验策略也随之发生了变化。本标准以基于三维模型制造的机械零部件几何尺寸检验为对象，结合基于三维模型的数字化接触式测量与非接触式测量方法的应用实践，融合国家标准、行业标准的要求，形成数字化环境下基于三维模型的数字化检验实施指南，为企业全面推进实施三维数字化检验提供参考和借鉴。

Electromechanical products Implementation Guide for digital inspection based on three-dimensional model

GSO ISO 21204:2022 产品几何规格 (GPS) 过渡规格

This document defines a number of specification operators for the specification of extended edge transition features between features. An edge transition feature is an integral feature connecting two adjacent integral features. The extended edge transition feature includes portions of the adjacent features. All these specifications apply to any line in a defined direction in the extended edge transition feature. This document also defines the specification modifiers and the drawing indications for such transition specifications. The proportions and dimensions of the graphical symbols to be used are also specified. The specifications defined in this document are suitable for relatively simple edge transition functions, for example ensuring assembly without interference. For more complex functions, geometrical tolerancing offers more precise tools. This document is by intention limited to only edge transition features between two planes and between a cylinder and a plane nominally perpendicular to it. Annex A gives the first approach for an algorithm to identify toleranced features and adjacent reference sections. This algorithm is subject to change as more experience is gathered. This document provides a set of tools to express several transition specifications. It does not present any information on the relationship between a function or a use and a transition specification. NOTE 1 Corners (the transition between three or more features) are not edge transition features and are consequently not covered by this document. NOTE 2 An edge transition feature exists between two single features. A defined edge transition feature has a defined nominal shape and is not sharp (r = 0).

Geometrical product specifications (GPS) — Transition specification

DIN EN ISO 21204:2022 几何产品规范（GPS） 过渡规范（ISO 21204:2020）；德文版 EN ISO 21204:2020

This document defines a number of specification operators for the specification of extended edge transition features between features. An edge transition feature is an integral feature connecting two adjacent integral features. The extended edge transition feature includes portio

Geometrical product specifications (GPS) - Transition specification (ISO 21204:2020); German version EN ISO 21204:2020

KS B ISO 2538-2:2021 产品几何技术规范（GPS）.楔块.第2部分:尺寸和公差

Geometrical product specifications(GPS) — Wedges —Part 2: Dimensioning and tolerancing

KS B ISO 2538-1:2021 几何产品规范（GPS）.楔块.第1部分:角度和坡度系列

Geometrical product specifications(GPS) — Wedges —Part 1: Series of angles and slopes