17.040.01 长度和角度测量综合 标准查询与下载

DS-håndbog 114.3:2012 几何产品规范（GPS） 第3部分：GPS 尺寸标准 规范和验证

This DS-handbook 114.3 contains standards for geometrical product specifications within the area "dimension".

Geometrical product specifications (GPS) - Part 3: GPS standards on dimension - Specification and verification

VDI/VDE 2634 Blatt 2-2012 光学 3-D 测量系统 基于区域扫描的光学系统

Die Richtlinie definiert Annahme- und ?berwachungsverfahren sowie Prüfk?rper zur Beurteilung von bildgebenden optischen 3-D-Messsystemen mit fl?chenhafter Antastung hinsichtlich ihrer Genauigkeit. Sie gilt für optische 3-D-Messsysteme mit fl?chenhafter Antastung, die nach dem Triangulationsprinzip arbeiten. Die beschriebenen Verfahren k?nnen nur für die Messung von 3-D-Objekten in einem elementaren Messvorgang ("Einzelansicht") angewendet werden. Nicht abgedeckt sind Systeme, die durch Repositionieren des Sensors und/oder des Objekts mehrere Einzelansichten in ein Objektkoordinatensystem transformieren.*www.vdi.de/2634

Optical 3-D measuring systems - Optical systems based on area scanning

LST EN ISO 17450-1:2012 几何产品规范（GPS） 一般概念 第1部分：几何规范和验证模型（ISO 17450-1:2011）

Geometrical product specifications (GPS) - General concepts - Part 1: Model for geometrical specification and verification (ISO 17450-1:2011)

LST EN ISO 1119:2012 几何产品规范（GPS） 锥度和锥角系列（ISO 1119:2011）

Geometrical product specifications (GPS) - Series of conical tapers and taper angles (ISO 1119:2011)

DS/EN ISO 17450-1:2012 几何产品规范（GPS） 一般概念 第1部分：几何规范和验证模型

This part of ISO 17450 provides a model for geometrical specification and verification and defines the corresponding concepts. It also explains the mathematical basis of the concepts associated with the model.

Geometrical product specifications (GPS) - General concepts - Part 1: Model for geometrical specification and verification

DS/EN ISO 1119:2012 几何产品规范（GPS） 锥度和锥角系列

This International Standard provides calculated values for a series of cones or conical tapers, ranging from 120° to less than 1°, or ratios from 1:0,289 to 1:500, intended for general use in technical engineering.

Geometrical product specifications (GPS) - Series of conical tapers and taper angles

LST EN ISO 22432:2012 几何产品规范（GPS） 规范和验证中使用的功能（ISO 22432:2011）

Geometrical product specifications (GPS) - Features utilized in specification and verification (ISO 22432:2011)

DS/EN ISO 22432:2012 产品几何规格（GPS） 规格和验证中使用的特征

This International Standard defines general terms and types of features for geometrical features ofspecifications for workpieces.

Geometrical product specifications (GPS) - Features utilized in specification and verification

EN ISO 17450-2:2012 几何产品规范(GPS).一般概念.第2部分:基本原则,规范,运营商,不确定性和模糊性

This part of ISO 17450 defines terms related to specifications, operators (and operations) and uncertaintiesused in geometrical product specifications (GPS) standards. It presents the basic tenets of the GPS philosophywhile discussing the impact of uncertainty on those tenets, and examines the processes of specification andverification as they apply to GPS.

Geometrical product specifications (GPS) - General concepts - Part 2: Basic tenets, specifications, operators, uncertainties and ambiguities

VDI/VDE/DGQ/DKD 2622 Blatt 15.1-2011 电量测量设备的校准-人工电源网络

The guideline covers the calibration of network emulations for power supply connectors. It is valid for network emulations, which correspond to the standard CISPR 16-1-2 in structure and requirements. The guideline defines a procedure for the calibration of the relevant characteristics of network emulations. Further the required standards as well as the documentation and evaluation of the measurement results are described. In the Annex a detailed determination of the uncertainty of measurement of the calibration is illustrated. Furthermore the deviation of the model equation for the determination of the uncertainty of measurement is shown.

Calibration for measuring equipment for electrical quantities - Artificial mains networks

LST EN ISO 14253-2:2011 几何产品规范（GPS） 通过测量工件和测量设备进行检验 第2部分：GPS 测量、测量设备校准和产品验证中的不确定性估计指南（ISO 1425

Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification (ISO 1425

LST EN ISO 25378:2011 产品几何规格（GPS） 特性和条件 定义（ISO 25378:2011）

Geometrical product specifications (GPS) - Characteristics and conditions - Definitions (ISO 25378:2011)

LST EN ISO 14253-3:2011 几何产品规范（GPS） 通过测量工件和测量设备进行检验 第3部分：达成测量不确定性声明协议的指南（ISO 14253-3:2011）

Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 3: Guidelines for achieving agreements on measurement uncertainty statements (ISO 14253-3:2011)

LST EN ISO 12780-2:2011 几何产品规范（GPS） 直线度 第2部分：规范运算符（ISO 12780-2:2011）

Geometrical product specifications (GPS) - Straightness - Part 2: Specification operators (ISO 12780-2:2011)

DS/EN ISO 25378:2011 产品几何规格（GPS） 特性和条件 定义

This document defines general terms for geometrical specifications, characteristics and conditions. These definitions are based on concepts developed in ISO/TS 17450-1 and ISO 22432 and they are given by using a mathematical description based on Annex B of ISO/TS 17450-1.This document is not intended for industrial use as such among designers, but is aimed to serve as the ""road map"" mapping out the requirements based on geometrical features, thus enabling future standardisation for industry and software makers in a consistent manner.“This document defines general types of geometrical characteristics and conditions, which can be used in GPS. These descript

Geometrical product specifications (GPS) - Characteristics and conditions - Definitions

DS/EN ISO 14253-2:2011 几何产品规范（GPS） 通过测量工件和测量设备进行检验 第2部分：GPS 测量、测量设备校准和产品验证中的不确定性估计指南

ISO 14253-2:2011 gives guidance on the implementation of the concept of the """"Guide to the estimation of uncertainty in measurement"""" (in short GUM) to be applied in industry for the calibration of (measurement) standards and measuring equipment in the field of GPS and the measurement of workpiece GPS characteristics. The aim is to promote full information on how to achieve uncertainty statements and provide the basis for international comparison of measurement results and their uncertainties (relationship between purchaser and supplier). ISO 14253-2:2011 is intended to support ISO 14253-1. Both parts are beneficial to all technical functions in a compa

Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification

DS/EN ISO 14253-3:2011 几何产品规范（GPS） 通过测量工件和测量设备进行检验 第3部分：达成测量不确定性陈述协议的指南

ISO 14253-3:2011 provides guidelines and defines procedures for assisting the customer and supplier to reach amicable agreements on disputed measurement uncertainty statements regulated in accordance with ISO 14253-1, and so avoid costly and time-consuming disputes.

Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 3: Guidelines for achieving agreements on measurement uncertainty statements

BS EN ISO 25378:2011 产品几何量技术规范(GPS).特性和条件.定义

This International Standard defines general terms for geometrical specifications, characteristics and conditions. These definitions are based on concepts developed in ISO 17450-1 and ISO 22432 and they are given by using a mathematical description based on Annex B of ISO 17450-1:2011. This International Standard is not intended for industrial use as such among designers, but is aimed to serve as the “road map” mapping out the requirements based on geometrical features, thus enabling future standardization for industry and software makers in a consistent manner. This International Standard defines general types of geometrical characteristics and conditions which can be used in GPS. These descriptions are applicable to - a workpiece, - an assembly, - a population of workpieces, and - a population of assemblies. These definitions are based on concepts of operators and the duality principle contained in ISO 17450-1 and ISO/TS 17450-2 and on the description of types of geometrical features defined in ISO 22432. Conceptually, these specification operators can be used as specification operators or as verification operators (duality principle). This International Standard is not intended to define GPS specifications, symbology or other types of expression.

Geometrical product specifications (GPS). Characteristics and conditions. Definitions

BS EN ISO 14253-2:2011 产品几何量技术规范(GPS).工件与测量设备的测量检验.GPS测量中,测量设备校准中和产品检验中不确定度的评估指南

This part of ISO 14253 gives guidance on the implementation of the concept of the “Guide to the estimation of uncertainty in measurement” (in short GUM) to be applied in industry for the calibration of (measurement) standards and measuring equipment in the field of GPS and the measurement of workpiece GPS characteristics. The aim is to promote full information on how to achieve uncertainty statements and provide the basis for international comparison of measurement results and their uncertainties (relationship between purchaser and supplier). This part of ISO 14253 is intended to support ISO 14253-1. Both parts are beneficial to all technical functions in a company in the interpretation of GPS specifications [i.e. tolerances of workpiece characteristics and values of maximum permissible errors (MPEs) for metrological characteristics of measuring equipment]. This part of ISO 14253 introduces the Procedure for Uncertainty MAnagement (PUMA), which is a practical, iterative procedure based on the GUM for estimating uncertainty of measurement without changing the basic concepts of the GUM. It is intended to be used generally for estimating uncertainty of measurement and giving statements of uncertainty for: - single measurement results; - the comparison of two or more measurement results; - the comparison of measurement results — from one or more workpieces or pieces of measurement equipment — with given specifications [i.e. maximum permissible errors (MPEs) for a metrological characteristic of a measurement instrument or measurement standard, and tolerance limits for a workpiece characteristic, etc.], for proving conformance or non-conformance with the specification. The iterative method is based basically on an upper bound strategy, i.e. overestimation of the uncertainty at all levels, but the iterations control the amount of overestimation. Intentional overestimation — and not underestimation — is necessary to prevent wrong decisions based on measurement results. The amount of overestimation is controlled by economical evaluation of the situation. The iterative method is a tool to maximize profit and minimize cost in the metrological activities of a company. The iterative method/procedure is economically self-adjusting and is also a tool to change/reduce existing uncertainty in measurement with the aim of reducing cost in metrology (manufacture). The iterative method makes it possible to compromise between risk, effort and cost in uncertainty estimation and budgeting.

Geometrical product specifications (GPS). Inspection by measurement of workpieces and measuring equipment. Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification

LST EN ISO 14406:2011 几何产品规范（GPS） 提取（ISO 14406:2010）

Geometrical product specifications (GPS) - Extraction (ISO 14406:2010)