17.040.10 极限和配合 标准查询与下载
共找到 276 条与 极限和配合 相关的标准，共 19 页
Geometrical product specifications(GPS) — Dimensional measuring equipment — Part 1: Plain limit gauges of linear size
- ICS
- 17.040.10
- CCS
- 发布
- 2020-11-10
- 实施
General tolerances — Part 1: Tolerances for linear and angular dimensions without individual tolerance indications
- ICS
- 17.040.10
- CCS
- 发布
- 2019-12-31
- 实施
General tolerances — Part 1: Tolerances for linear and angular dimensions without individual tolerance indications
- ICS
- 17.040.10
- CCS
- 发布
- 2019-12-31
- 实施
This document illustrates the ambiguity caused by the use of dimensional specifications to control properties other than linear or angular size and the benefit of using geometrical specifications instead. Dimensional tolerancing can be indicated by ± tolerancing or geometrical specifications. The ambiguity caused by using ± tolerances for dimensions other than linear or angular sizes (for individual tolerances and general tolerances according to, e.g. ISO 2768-1 and ISO 8062-3) is explained in Annex A. NOTE 1 The figures, as shown in this document, merely illustrate the text and are not intended to reflect actual usage. The figures are consequently simplified to indicate only the relevant principles. NOTE 2 For indications of dimensional specifications, see the following: NOTE 3 The rules for geometrical specifications are given in ISO 1101.
Geometrical product specifications (GPS) — Dimensional tolerancing — Part 3: Angular sizes
- ICS
- 17.040.10
- CCS
- 发布
- 2018-12-14
- 实施
- 0000-00-00
Castings — System of dimensional tolerances and machining allowances
- ICS
- 17.040.10
- CCS
- 发布
- 20181031
- 实施
- 20181031
Geometrical product specifications (GPS) - Geometrical tolerancing - Pattern and combined geometrical specification
- ICS
- 17.040.10
- CCS
- 发布
- 2018-06-01
- 实施
This document specifies general geometrical tolerances using surface profile tolerances related to a general datum system that remains on the final part. It also specifies machining allowances and draft angles (tapers) for castings in all cast metals and their alloys produced by various casting manufacturing processes. NOTE When there is no datum system (target or integral) on surfaces remaining in the final condition, this document cannot be applied.
Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 4: General tolerances for castings using profile tolerancing in a general datum system
- ICS
- 17.040.10
- CCS
- 发布
- 2017-07-31
- 实施
- 0000-00-00
Geometrical product specifications(GPS) — Dimensional tolerancing — Part 2: Dimensions other than linear sizes
- ICS
- 17.040.10
- CCS
- 发布
- 2017-01-10
- 实施
Geometrical product specifications(GPS) — Dimensional tolerancing — Part 2: Dimensions other than linear sizes
- ICS
- 17.040.10
- CCS
- 发布
- 2017-01-10
- 实施
Geometrical product specifications(GPS) — Dimensional tolerancing — Part 1: Linear sizes
- ICS
- 17.040.10
- CCS
- 发布
- 2017-01-10
- 实施
Geometrical product specifications(GPS) — Dimensional tolerancing — Part 1: Linear sizes
- ICS
- 17.040.10
- CCS
- 发布
- 2017-01-10
- 实施
Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 2: Reference disk gauges
- ICS
- 17.040.10
- CCS
- J42
- 发布
- 2017-01-01
- 实施
This part of ISO 14405 establishes the default specification operator for angular size and defines a number of special specification operators for features of angular size: cone (truncated, i.e. frustum, or not), wedge (truncated or not), two opposite straight lines (intersection of a wedge/truncated wedge and a plane perpendicular to the intersection straight line of the two planes of the wedge/truncated wedge, intersection of a cone/frustum and a plane containing the axis of revolution of the cone/frustum). See Figure 1 and Figure 2. This part of ISO 14405 also defines the specification modifiers and the drawing indications for these angular sizes. This part of ISO 14405 covers the following angular sizes: — local angular size: — angular size between two lines; — portion angular size; — global angular size: — direct global angular size: — least squares angular size; — minimax angular size; — rank order angular size/indirect global angular size: — maximum angular size; — minimum angular size; — average angular size; — range of angular sizes; — mid-range angular size; — median angular size; — standard deviation of angular size. This part of ISO 14405 defines the meaning of tolerances of angular sizes indicated as — + and/or - limit deviations, e.g. 0°/-0,5°, or — indicated with upper limit of size (ULS) and/or lower limit of size (LLS), e.g. 35° max. or 15° min., 34°/36°, — with or without modifiers. This part of ISO 14405 provides a set of tools to express several types of angular size characteristics. It does not give any information on the relationship between a function or a use and an angular size characteristic.
Geometrical product specifications (GPS) — Dimensional tolerancing — Part 3: Angular sizes
- ICS
- 17.040.10
- CCS
- 发布
- 2016-12-13
- 实施
- 0000-00-00
Geometrical product specifications(GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits
- ICS
- 17.040.10
- CCS
- 发布
- 2016-11-30
- 实施
Geometrical product specifications(GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits
- ICS
- 17.040.10
- CCS
- 发布
- 2016-11-30
- 实施
General tolerances — Part 1: Tolerances of linear and angular dimensions without individual tolerance indications
- ICS
- 17.040.10
- CCS
- 发布
- 2016-11-30
- 实施
Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits
- ICS
- 17.040.10
- CCS
- 发布
- 2016-11-30
- 实施
Geometrical product specifications (GPS). Dimensional tolerancing. Linear sizes
- ICS
- 17.040.10
- CCS
- A50
- 发布
- 2016-09-30
- 实施
- 2016-09-30
