17.040.10 极限和配合 标准查询与下载

DS/EN ISO 286-2:2010 几何产品规范（GPS） 线性尺寸公差的 ISO 代码系统 第2部分：孔和轴的标准公差等级和极限偏差表

This part of ISO 286 gives values of the limit deviations for commonly used tolerance classes for holes and shafts calculated from the tables given in ISO 286-1. This part of ISO 286 covers values for the upper limit deviations ES (for holes) and es (for shafts), and the lower limit deviations EI (for holes) and ei (for shafts)

Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts

BS EN ISO 286-1:2010 几何产品规范（GPS）.线性尺寸公差的ISO编码系统.公差、偏差和配合的基础

This part of ISO 286 establishes the ISO code system for tolerances to be used for linear sizes of features of the following types: a) cylinder; b) two parallel opposite surfaces. It defines the basic concepts and the related terminology for this code system. It provides a standardized selection of tolerance classes for general purposes from amongst the numerous possibilities. Additionally, it defines the basic terminology for fits between two features of size without constraints of orientation and location and explains the principles of “basic hole” and “basic shaft”.

Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Basis of tolerances, deviations and fits

KS B ISO 286-1:2009 线性尺寸公差的ISO规范体系.第1部分:基本公差、偏差和定值

이 표준은 치수 공차 및 끼워 맞춤 방식의 기본 사항과 기본 공차 및 기초가 되는 치수 허

ISO system of limits and fits-Part 1:Bases of tolerances, deviations and fits

BS 1916-2:2009 工程的公差与配合.BS1916-1中配合选择的指南

This British Standard gives guidance on the selection of fits given in BS 1916-1. The recommendations apply, in particular, to fits between cylindrical parts, designated as “holes” and “shafts”, in which case the term “size” refers to the diameter of the mating parts. The recommendations are also applicable to parts other than cylindrical, in which case the term “size” refers to a length, width or other dimension. Tables of preferred sizes are included to avoid the indiscriminate selection of dimensions, and their use is strongly recommended.

Limits and fits for engineering Part 2: Guide to the selection of fits in BS 1916-1

BS 1916-1:2009 工程用极限与配合.第1部分:极限与公差指南

This part of BS 1916 gives guidance on tolerances, limits and fits for engineering sizes up to 19.69 in. The recommendations apply particularly to fits between cylindrical parts, designated as “holes” and “shafts”, in which case the term “size” refers to the diameter of the mating parts. The data may also be applied in appropriate cases, by suitable selection of the grades of allowance and tolerances, to fits between other than cylindrical mating parts, in which case the “size” refers to a length, width or other dimension instead of to a diameter. The system described in this British Standard comprises suitable combinations of 16 grades of tolerance and 21 types of fit for both hole and shaft, ranging from fits of extreme interference to those of extreme clearance. All but very exceptional engineering requirements are covered, from very coarse work to fine gauge manufacture. A selection of fits for general use is given in Figure 4, and further guidance on tolerances for shafts and holes for a wide range of fits is given in Part 2 of this British Standard, but it is intended that a particular industry or organization extracts and uses those limits which suit its own product. A unilateral hole basis system is recommended but a full range of holes suitable for use on a shaft basis system, unilateral or bilateral, is also included in the tables.

Limits and fits for engineering Part 1: Guide to limits and tolerances

BS 1916-3:2009 工程公差和配合.大直径的公差,极限和配合指南

This part of BS 1916 gives guidance on tolerances, limits and fits for large diameters (19.69 in to 125 in). In many industries, components in large sizes are made to interchangeable as well as to matched fits. There are many practical problems, however, in achieving interchangeable manufacture in large diameters, due mainly to difficulties of measurement. Clause 4 and Clause 5 in Section 1 discuss the known difficulties which might be encountered and draw attention to those tolerances and fits where the greater difficulties might be expected to arise. Section 2 puts forward tables of tolerances, deviations and limits for shafts and holes. It is strongly emphasized that these should be regarded as recommendations intended for trial purposes. They are published in the expectation that experience in their use will enable them to be confirmed or modified, and will help to bring to light deficiencies in measuring techniques. An explanation of the system to which this standard forms an extension is contained in BS 1916-1.

Limits and fits for engineering. Guide to tolerances, limits and fits for large diameters

BS 4500:2009 公差和配合.锥形配合系统和从C=1:3到1:500,长度从6 mm至630 mm直径小于等于500 mm的锥形的公差系统指南

This British Standard gives guidance on a system of cone fits and tolerances for cones from C = 1:3 to 1:500 and lengths from 6 mm to 630 mm. The appropriate tolerances of this British Standard can also be used for prismatic workpieces, for example wedges. This British Standard applies to cones which are dimensioned and toleranced according to BS ISO 3040, Method 1, Basic Taper method. This means that the tolerances limit the variation of penetration of mating surfaces, each surface being within two limiting profiles of the same taper corresponding to the maximum material condition (MMC) and the least material condition (LMC). This British Standard is derived from BS EN 20286, and is a complement to BS EN ISO 1119. NOTE For dimensioning and tolerancing cones on drawings, see BS ISO 3040.

Limits and fits - Guidance for system of cone (taper) fits and tolerances for cones from C = 1:3 to 1:500, lengths from 6 mm to 630 mm and diameters up to 500 mm

LST EN ISO 8062-3:2007/AC:2009 几何产品规范（GPS） 模制零件的尺寸和几何公差 第3部分：铸件的一般尺寸和几何公差和加工余量（ISO 8062-3:2007/Cor 1:2009）

Geometrical Product Specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 3: General dimensional and geometrical tolerances and machining allowances for castings (ISO 8062-3:2007/Cor 1:2009)

BS 969:2008 普通极限量规的极限和公差规范

This British Standard specifies tolerances and limits for simple forms of limit gauges, such as cylindrical plain plug, ring and gap gauges, for which gauge limits have not been stipulated. It specifies gauge tolerances for workpiece tolerances in the range between 0.009 mm and 3.200 mm and how gauge limits are related to the workpiece limits. It also specifies types of gauge according to size and minimum workpiece tolerance. NOTE Where a workpiece tolerance is outside the range 0.009 mm to 3.200 mm, or if it is not possible to conform to Table 2 regarding type of gauge, gauge tolerance and workpiece size, direct measurement should be used. The gauge tolerances specified are such that the size of any workpiece accepted by a gauge lies within the boundaries constituted by the workpiece limits. Furthermore, the magnitude of the gauge tolerances is consequent upon the amount of the workpiece tolerance only. A wear allowance is provided on all GO gauges, i.e. those that control the maximum material condition of the workpiece.

Specification for limits and tolerances on plain limit gauges

KS P ISO 10079-1:2008 医疗吸引设备、第1部分:电动吸引设备、安全要求

이 표준은 병원 또는 가정 및 실외, 이동 중 사용되는 의료용 및 수술용 흡인기(그림 1

Medical suction equipment－Part 1: Electrically powered suction equipment－Safety requirements

LST EN ISO 8062-3:2007 几何产品规范（GPS） 模制零件的尺寸和几何公差 第3部分：铸件的一般尺寸和几何公差和加工余量（ISO 8062-3:2007）

Geometrical Product Specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 3: General dimensional and geometrical tolerances and machining allowances for castings (ISO 8062-3:2007)

KS B 0243-2007(2012) 基准和系统技术DATUM 几何公差

Datums and datum-systems for geometrical tolerances

KS B 0243-2007 几何公差数据系统

이 규격은 기하학적 공차를 지시할 때에 사용하는 데이텀 및 데이텀 시스템의 도시 방법 및

Datums and datum-systems for geometrical tolerances

GSO ISO 8062:2007 铸件 尺寸公差和加工公差系统

This standard specifies a system of tolerance grades and required machining allowance grades for the dimensions of castings. It is applicable to the dimensions of cast metals and their alloys produced by various casting manufacturing processes (see clause 5). This standard applies both to general tolerances and/or required machining allowances given on a drawing and to individual tolerances and/or required machining allowances which are shown immediately following a specific dimensions (see clause 11). The system specified applies when the foundry provides the pattern or die equipment or accepts responsibility for proving it.

CASTINGS ? SYSTEM OF DIMENSIONAL TOLERANCES AND MACHINING ALLOWANCES

KS B 0146-2006 一般公差 第2部分：没有单独公差标记的特征的几何公差

GENERAL TOLERANCES-PART2:GEOMETRICAL TOLERANCES FOR FEATURES WITHOUT INDIVIDUAL TOLERANCE INDICATIONS

KS B ISO 16570-2006(2011) 产品几何技术规范（GPS）－线性和角度尺寸及公差:＋/－极限规范－台阶尺寸、距离、角度尺寸和半径

Geometrical Product Specifications(GPS)－Linear and angular dimensioning and tolerancing：＋/－limit specifications－Step dimensions, distances, angular sizes and radii

ISO 286-2:1988/Cor 1:2006 ISO极限和配合体系-第2部分：孔和轴的标准公差等级和极限偏差表；技术勘误表1

This is Technical Corrigendum 1 to ISO 286-2-1-1988 (ISO system of limits and fits — Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts )

ISO system of limits and fits - Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts; Technical Corrigendum 1

KS B ISO 1829-2004(2009) 公差区选用一般用途

Selection of tolerance zones for general purposes

ISO 8062-4 几何产品规范（GPS）“模制零件的尺寸和几何公差”第4部分：在通用基准系统中使用轮廓公差的铸件的规则和通用公差

Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 4: Rules and general tolerances for castings using profile tolerancing in a general datum system

ISO/CD 14405-1 产品几何规格（GPS）“尺寸公差”第1部分：线性尺寸

Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes