21.040.30 特殊螺纹 标准查询与下载

CEN EN 10226-2-2005 在螺纹上制成压力密封接头的管螺纹 第2部分：锥度、外螺纹和锥度内螺纹 尺寸、公差和名称

This European Standard specifies the requirements for thread form, dimensions, tolerances and designation for jointing pipe threads, sizes 1/16 to 6 inclusive, for joints made pressure-tight by the mating of the threads. These threads are taper external and taper internal and are intended for use with pipes suitable for threading and for valves, fittings or other pipeline equipment interconnected by threaded joints. An appropriate thread sealant or jointing compound should be used on the thread to ensure pressure-tight joints. NOTE 1 Threaded joints using taper external threads and parallel internal threads are detailed in EN 10226-1. NOTE 2 The requirements for taper external threads are identical in EN 10226-1 and EN 10226-2. NOTE 3 For pipe threads where pressure-tight joints are not made on the threads see EN ISO 228-1. NOTE 4 EN 10226-3 gives details of recommended gauging systems for the verification of thread dimensions and thread form.

Pipe threads where pressure tight joints are made on the threads — Part 2: Taper, external threads and taper internal threads — Dimensions, tolerances and designation

ASME B1.20.2M-2006 一般用途用60℃管螺纹

ASME B.1.20.2M-2006; Pipe Threads, 60 deg, General Purpose (Metric) Standard is a metric conversion of the widely accepted ASME B1.20.1-1983; Pipe Threads, General Purpose (Inch) Standard NPT Taper Pipe Threads. The ASME B1 Standards Committee prepared this metric translation in order to encourage global use and acceptance of the NPT Pipe Thread. For ease of use, product threads and gauging are contained in the Standard. There are no changes to the thread or gage designs.

Pipe Threads, 60 deg, General Purpose

DIN EN 10226-2:2005 螺纹上有压力密封接缝的管螺纹.第2部分:锥形外螺纹和锥形内螺纹.尺寸、公差和名称与符号

This European Standard specifies the requirements for thread form, dimensions, tolerances and designation for 'q" jointing pipe threads, sizes 1/16 to 6 inclusive, for joints made pressure-tight by the mating of the threads. These threads are taper external and taper internal and are intended for use with pipes suitable for threading and for valves, fittings or other pipeline equipment interconnected by threaded joints. An appropriate thread sealant or jointing compound should be used on the thread to ensure pressure-tight joints. NOTE 1 Threaded joints using taper external threads and parallel internal threads are detailed in EN 10226-1 NOTE 2 The requirements for taper external threads are identical in EN 10226-1 and EN 10226-2. NOTE 3 For pipe threads where pressure-tight joints are not made on the threads see EN ISO 228-1 NOTE 4 EN 10226-3 gives details of recommended gauging systems for the verification of thread dimensions and thread form

Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation;English version of DIN EN 10226-2

LST EN 10226-2-2005 在螺纹上形成压力密封接头的管螺纹 第2部分：锥形外螺纹和锥形内螺纹 尺寸、公差和名称

Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation

BS EN 10226-3:2005 螺纹上有压力密封接缝的管螺纹.用极限量规验证

This document specifies a process using limit gauges, for the validation of taper internal and external threads and parallel internal threads on piping systems components and other products, the dimensions and tolerances of which are detailed in EN 10226-1 and prEN 10226-2. The gauging system described may not be suitable, without special precautions, for gauging of threads on injection moulded plastic workpieces. This document does not cover completely all the requirements necessary for full control of thread quality and dimensions. Additional control of tools and equipment and visual inspection during production are required to ensure complete compliance with EN 10226-1 and prEN 10226-2, for example the length of useful thread on internally threaded workpieces should be checked by direct measurement. Annex A gives a summary of the gauges included in this document, together with details of the thread elements controlled by each gauge and gauge identification numbers. In the event of a dispute over compliance with the requirements of EN 10226-1 and prEN 10226-2, the gauges in this document are to be considered as decisive for the thread elements which they control on the workpiece.

Pipe threads where pressure-tight joints are made on the threads - Verification by means of limit gauges

EN 10226-2:2005 螺纹上压力强密联接的管螺纹.第2部分:锥形外螺纹和锥形内螺纹.尺寸,公差及名称和符号

This European Standard specifies the requirements for thread form, dimensions, tolerances and designation for jointing pipe threads, sizes 1/16 to 6 inclusive, for joints made pressure-tight by the mating of the threads. These threads are taper external and taper internal and are intended for use with pipes suitable for threading and for valves, fittings or other pipeline equipment interconnected by threaded joints.An appropriate thread sealant or jointing compound should be used on the thread to ensure pressure-tight joints.NOTE 1 Threaded joints using taper external threads and parallel internal threads are detailed in EN 10226-1.NOTE 2 The requirements f

Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation

DS/EN 10226-1:2005 在螺纹上制成压力密封接头的管螺纹 第1部分：锥形外螺纹和平行内螺纹 尺寸、公差和名称

This part of EN 10226 specifies the requirements for thread form, dimensions, tolerances and designation for jointing pipe threads, sizes 1/16 to 6 inclusive, for joints made pressure tight by the mating of the threads. These threads are taper external (designated by R) and parallel internal (designated by Rp) and are intended for use with pipes suitable for threading and for valves, fittings or other pipeline equipments interconnected by threaded joints.

Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation

LST EN 10226-3-2005 在螺纹上制成压力密封接头的管螺纹 第3部分：通过限位规进行验证

Pipes threads where pressure tight joint are made on the threads - Part 3: Verification by means of limit gauges

DIN EN 10226-3:2005 螺纹上有压力密封接缝的管螺纹.第3部分:通过极限量规验证

The standard specifies a process using limit gauges, for the validation of taper internal and external threads and parallel internal threads on piping systems components and other products.#,,#

Pipes threads where pressure tight joint are made on the threads - Part 3: Verification by means of limit gauges; German version EN 10226-3:2005

SANS 1109-2:2005 用其制造气密接头的管螺纹．第2部分：使用极限规进行检验

Specifies a process using limit gauges, for the validation of taper internal and external threads and parallel internal threads on piping systems components and other products, the dimensions and tolerances of which are detailed in SANS 1109-1.

Pipe threads where pressure-tight joints are made on the threads Part 2: Verification by means of limit gauges

SANS 1109-1:2005 用其制造气密接头的管螺纹．第1部分：尺寸，容差和名称

Specifies the requirements for thread form, dimensions, tolerances and designation for jointing pipe threads, sizes 1/16 to 6 inclusive, for joints made pressure-tight by the mating of the threads. These threads are taper external, parallel internal or t

Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation

EN 10226-3:2005 螺纹上有压力密封接缝的管螺纹.第3部分:用极限量规验证

This document specifies a process using limit gauges, forThe validation of taper internal and external threads and parallel internal threads on piping systems components and other products,The dimensions and tolerances of which are detailed in EN 10226-1 and prEN 10226-2.

Pipes threads where pressure tight joint are made on the threads - Part 3: Verification by means of limit gauges

BS EN 10226-2:2005(2016) 在螺纹上形成压力密封接头的管螺纹 锥形外螺纹和锥形内螺纹 尺寸、公差和名称

Pipe threads where pressure tight joints are made on the threads - Taper external threads and taper internal threads - Dimensions, tolerances and designation

DIN 20401:2004 锯齿螺纹.0.8至2mm的螺距.尺寸

Threads according to this standard are intended for components, e. g. slit bolts according to DIN 22412. These threads are designed so that the axial forces effected by tightening the nut can be converted in radial forces only in minor parts.#,,#

Buttress threads - 0,8 mm to 2 mm pitch - Dimensions

NF E03-004-1*NF EN 10226-1:2004 用螺纹密封的管螺纹.第1部分:自攻外螺纹和平行内螺纹.尺寸、公差与标记

Pipe threads where pressure tight joints are made on the threads - Part 1 : taper external threads and parallel internal threads - Dimensions, tolerances and designation.

DIN EN 10226-1:2004 有压力紧固连接件的管道螺纹.第1部分:锥形外螺纹和平行内螺纹.尺寸、公差和名称与符号

This part of EN 10226 specifies the requirements for thread form, dimensions, tolerances and designation for jointing pipe threads, sizes 1/16 to 6 inclusive, for joints made pressure-tight by the mating of the threads.

Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation; German version EN 10226-1:2004

LST EN 10226-1-2004 在螺纹上制成压力密封接头的管螺纹 第1部分：锥形外螺纹和平行内螺纹 尺寸、公差和名称

Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation

EN 10226-1:2004 有压力紧固连接件的管道螺纹.第1部分:锥形外螺纹和平行内螺纹.尺寸,公差和名称与符号

This part of EN 10226 specifies the requirements for thread form, dimensions, tolerances and designation for jointing pipe threads, sizes 1/16 to 6 inclusive, for joints made pressure-tight byThe mating of the threads.These threads are taper external and parallel internal and are intended for use with pipes suitable for threading and for valves, fittings or other pipeline equipment interconnected by threaded joints.

Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads; Dimensions, tolerances and designation

ASME B1.10M-2004 统一标准的小型螺纹

This Standard specifies the thread form, series, tolerance, and designation for the Unified Miniature Screw Threads. The series covers a diameter range of 0.30 mm to 1.40 mm, extending the metric M-Profile and unified thread series that begin at 1.6 mm.

Unified Miniature Screw Threads

ANSI/ASME B1.10M-2004 统一微型螺纹

Specifies the thread form, series, tolerance, and designation for the Unified Miniature Screw Threads. The series covers a diameter range of 0.30 mm to 1.40 mm, extending the metric M-Profile and unified thread series that begin at 1.6 mm.

Unified Miniature Screw Threads