21.060.70 卡箍和U形环 标准查询与下载

ASTM F708-24 刚性管道吊架设计和安装的标准实施规程

1.1  This practice covers acceptable methods of fabricating and installing rigid pipe hangers used to support shipboard piping systems with temperatures of 650 °F (343 °C) or less. 1.2  This practice provides guidance for the design of hanger caps, straps and standoffs, selection of hanger and hanger liner materials, hanger bolting, and hanger spacing. 1.3  Other hanger designs may be used provided they result in an adequately supported vibration-free piping system and are compatible with the intended system service and temperature limitations. 1.4  The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Design and Installation of Rigid Pipe Hangers

KS B 3634-2022 手拉铆枪

Hand riveter

ASTM F708-92(2022) 刚性管道吊架的设计和安装

1.1 This practice covers acceptable methods of fabricating and installing rigid pipe hangers used to support shipboard piping systems with temperatures of 650 °F (343 °C) or less. 1.2 This practice provides guidance for the design of hanger caps, straps and standoffs, selection of hanger and hanger liner materials, hanger bolting, and hanger spacing. 1.3 Other hanger designs may be used provided they result in an adequately supported vibration-free piping system and are compatible with the intended system service and temperature limitations. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Design and Installation of Rigid Pipe Hangers

ASTM F1145-05(2022) 锻制焊接螺丝扣标准规范

1.1 This specification covers swaged welded, cast, or forged turnbuckles with and without jam nuts. 1.2 A turnbuckle is an internally threaded loop or sleeve intended for assembly with a threaded stud, eye, hook, or jaw at each end, used for applying tension to rods, wire rope, and so forth. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Turnbuckles, Swaged, Welded, Forged

DIN EN 13411-7:2022 钢丝绳端头 安全 第7部分：对称楔形插座；德文版 EN 13411-7:2021

This document specifies the minimum requirements for symmetrical wedge socket terminations for stranded steel wire ropes conforming to EN 12385-5 for lifts. This document covers those symmetric wedge sockets intended for use at temperatures between -20 °C and 100 °C. This documen

Terminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket; German version EN 13411-7:2021

DIN EN 13411-9:2021 钢丝绳端头 安全 第9部分：实心套管；德文版 EN 13411-9:2021

This document specifies the minimum requirements for solid thimbles made of steel or cast iron for terminations of stranded steel wire ropes. This document is applicable to ferrule-secured terminations with solid thimbles in combination with ferrules (see EN 13411-3), that have a

Terminations for steel wire ropes - Safety - Part 9: Solid thimbles; German version EN 13411-9:2021

LST EN 13411-7-2021 钢丝绳的端接 安全 第7部分：对称楔形插座

Terminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket

PN-EN 13411-9-2021-09 E 钢丝绳的端头 安全 第9部分：实心套管

Terminations for steel wire ropes -- Safety -- Part 9: Solid thimbles

DIN 3017-1:2021 软管夹 第1部分：带蜗轮驱动的夹具，形状 A 和 B

This document applies for hose clamps with worm gear drive which are used for mounting hoses on mobile and stationary facilities. This document lays down technical principles and conditions preferably to be used when supplying hose clamps with worm gear drive, shapes A and B.

Hose clamps - Part 1: Clamps with worm gear drive, shapes A and B

DIN 86016:2021 用于海洋管道的带嵌体的螺纹钢管夹 适用于外径从 15 毫米到 219 毫米的管道

This document applies to pipe clamps made of steel with an insert, which are used when laying pipes made of any material on ships. They establish a connection to the hull via a breakpoint. They are tailored to the needs of civil shipbuilding. The standard describes pipe clamps ba

Screwed steel pipe clamps with inlay for marine pipelines - For pipe outer diameters from 15 mm to 219 mm

LST EN 13411-9-2021 钢丝绳的端头 安全 第9部分：实心套管

Terminations for steel wire ropes - Safety - Part 9: Solid thimbles

DS/EN 13411-7:2021 钢丝绳端头《安全》第7部分：对称楔形插座

Terminations for steel wire ropes – Safety – Part 7: Symmetric wedge socket

BS EN 13411-7:2021 钢丝绳接线端 安全 对称楔形连接套筒

Terminations for steel wire ropes. Safety. Symmetric wedge socket

EN 13411-7:2021 终端钢丝绳.安全.第7部分:对称楔形插座

Terminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket

DS/EN 13411-9:2021 钢丝绳端头《安全》第9部分：实心套管

Terminations for steel wire ropes – Safety – Part 9: Solid thimbles

JIS A 5556:2021 订书钉

Staples

ASTM F1025-19 聚乙烯气体压力管穿孔或孔加固或修理用全环型带夹的选择和使用的标准指南

1.1 This guide specifically addresses the design and installation of full-encirclement-type band clamps for repair of gouges, punctures, or holes, and for reinforcement of polyethylene plastic pipe. Guidelines are provided for selecting and using clamps in pipe sizes 2 in. nominal (60 mm) and larger. 1.1.1 A test method is also provided for the user to assess the applicability of the repair clamp. Under appropriate circumstances, this type of clamp offers a convenient, effective, and safe means of restoring the integrity of an in-service pipeline, without cutting out a section of pipe (see Note 1). The pipe to be repaired cannot be backed by a stiffener for internal support and cross-sectional dimensional control. Satisfactory use of this type of clamp should rely on the crush resistance of the pipe itself and a fitting design concept, which retains the cross-sectional pipe configuration while minimizing compressive forces required to obtain an effective leakage seal. NOTE 1—The appropriateness for use of this type of clamp should be determined by using the information contained in this guide and from consultation with, and recommendations of, both the pipe and clamp manufacturers. The basic premise for use of this type of clamp is that it is recommended by the manufacturer for this specific application and that step-by-step installation instructions are available for that application. It is important in the development of this type of clamp that prototype testing be conducted to evaluate performance expectations because of the physical limitations encountered when designing it for use with plastic pipe. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Selection and Use of Full-Encirclement-Type Band Clamps for Reinforcement or Repair of Punctures or Holes in Polyethylene Gas Pressure Pipe

ASTM F1145-05(2017) 锻制 锻造 锻造的螺丝扣的标准规范

Standard Specification for Turnbuckles, Swaged, Welded, Forged

DIN 3021-2:2016 软管夹子.弹簧带夹子.第2部分:交货技术条件

Hose clamps - Spring band clamp - Part 2: Technical delivery conditions

DIN 3021-1:2016 软管夹件.弹簧板夹件(FBS).第1部分:尺寸、标记、材料和类型

Hose clamps - Spring band clamp - Part 1: Dimensions, marking, materials, types