21.120.10 轴 标准查询与下载
共找到 127 条与 轴 相关的标准，共 9 页
Driving and driven machines－Shaft heights
- ICS
- 21.120.10
- CCS
- 发布
- 2013-12-18
- 实施
Calculation of load capacity of shafts and axles - Part 2: Theoretical stress concentration factors and fatigue notch factors
- ICS
- 21.120.10
- CCS
- J10
- 发布
- 2012-12
- 实施
- 2012-12
Calculation of load capacity of shafts and axles - Supplement 1: Examples to part 1 to 3
- ICS
- 21.120.10
- CCS
- J10
- 发布
- 2012-12
- 实施
Calculation of load capacity of shafts and axles - Part 4: Fatigue limit, endurance limit - Equivalently damaging continuous stress
- ICS
- 21.120.10
- CCS
- J10
- 发布
- 2012-12
- 实施
Calculation of load capacity of shafts and axles - Part 1: General
- ICS
- 21.120.10
- CCS
- J10
- 发布
- 2012-12
- 实施
Calculation of load capacity of shafts and axles - Part 3: Strength of materials
- ICS
- 21.120.10
- CCS
- J10
- 发布
- 2012-12
- 实施
- 2012-12
Calculation of load capacity of shafts and axles - Supplement 2: Examples to part 4
- ICS
- 21.120.10
- CCS
- J10
- 发布
- 2012-12
- 实施
Involute splines based on reference diameters - Part 2: Nominal and inspection dimensions
- ICS
- 21.120.10
- CCS
- J18
- 发布
- 2012-09
- 实施
Shaft to collar connection - Polygon profile P4C - Part 2: Calculation and dimensioning
- ICS
- 21.120.10
- CCS
- J05
- 发布
- 2012-03-01
- 实施
Mechanical transmissions - Shafts and axles, calculation of load capacity - Part 2 : influence factors.
- ICS
- 21.120.10
- CCS
- J10
- 发布
- 2012-03-01
- 实施
- 2012-03-22
Mechanical transmissions - Shafts and axles, calculation of load capacity - Part 1 : general.
- ICS
- 21.120.10
- CCS
- J10
- 发布
- 2012-03-01
- 实施
- 2012-03-22
In this standard treats straight-sided splines with 0°angle of pressure, heavy series. This heavy series has relative to the DIN ISO 14 more teeth for higher load capacity. This standard provides geometry and the associated tolerances. The fundamental procedure details for the inspection from DIN ISO 14 are here also valid and not indicated additionally.
Straight-sided splines - Heavy series
- ICS
- 21.120.10
- CCS
- J18
- 发布
- 2010-03
- 实施
本标准规定了仪表用轴尖的产品型式、要求、试验方法、检验规则及标志、包装和贮存。 本标准适用于仪表活动部分球面支承用的轴尖。
Pivots for instruments
- ICS
- 21.120.10
- CCS
- N05
- 发布
- 2010-02-11
- 实施
- 2010-07-01
本标准规定了仪表用轴座的产品分类、要求、试验方法、检验规则及标志、包装和贮存。 本标准适用于仪表活动部分支承轴尖用的轴座。
Axle seat for instruments
- ICS
- 21.120.10
- CCS
- N05
- 发布
- 2010-02-11
- 实施
- 2010-07-01
This translation has been made based on the Amendment to the origi¬nal Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee as the result of proposal for revision of Japanese Industrial Standard with the draft being attached, based on the provision of Article 12 Clause 1 of the Industrial Standardization Law applicable to the case of revision by the provision of Article 14. Consequently, JIS B 0904:2001 is partially replaced with this Amendment.
Conical shaft ends for cone taper ratio 1:10 (Amendment 1)
- ICS
- 21.120.10
- CCS
- J04
- 发布
- 2009-03-20
- 实施
- 2009-03-23
Shaft to collar connection - Polygon profile P4C - Part 2: Calculation and dimensioning
- ICS
- 21.120.10
- CCS
- J05
- 发布
- 2009-03
- 实施
Shaft to collar connection - Polygon profile P4C - Part 1: Generalities and geometry
- ICS
- 21.120.10
- CCS
- J05
- 发布
- 2009-03
- 实施
The standard applies to the calculation of the dimensions and load-bearing capacity of P3G polygon profiles, as well as to the production of parts with such profiles. The scope of this standard extends to industrial products, e.g. those used in general engineering, and in machine tool, motor vehicle and aircraft construction, as well as in the electronics industry.
Shaft to collar connection - Polygon profile P3G - Part 2: Calculation and dimensioning
- ICS
- 21.120.10
- CCS
- J05
- 发布
- 2009-03
- 实施
The standard specifies the dimensions and geometry difinition of P3G polygon connections. The scope of this standard extends to industrial products, e.g. those used in general engineering, and in machine tool, motor vehicle and aircraft construction, as well as in the electronics industry.
Shaft to collar connection - Polygon profil P3G - Part 1: Generalities and geometry
- ICS
- 21.120.10
- CCS
- J05
- 发布
- 2009-03
- 实施
Involute splines based on reference diameters - Part 16: Tools, Corrigendum to DIN 5480-16:2006-03
- ICS
- 21.120.10
- CCS
- J18;J15
- 发布
- 2009-01
- 实施
